Ok. So i should set up a virtual port and use win4k suite. Can you elaborate a bit more on where the dxlab and rsba1 should be connected and how? Regards and merry christmas Ghassan Od5ya Sent from

+ AA6YQ comments below In the past if I was working a station in FT8, during the QSO the call I'm working would display in DXView and also show me past QSO's with that station. Recently I noticed

+ AA6YQ comments below My experience has been that after I log a QSO, the only QSO appearing in my log is the QSO that I just logged. + What actions are you taking to log a QSO? In order to

+ AA6YQ comments below I would like to permanently delete the "Auxiliary" and "QSL" fields from the "Log QSO's" tab page of DXKeeper, but even though I uncheck these fields in the DXKeeper "Log

I see that the 7610 has a dedicated cw speed  knob, so adjusting the tx speed with winwarbler in CAT mode is pretty easy to do. 73 Mark N1UK

In the past if I was working a station in FT8, during the QSO the call I'm working would display in DXView and also show me past QSO's with that station. Recently I noticed that is not happening

Thanks for your hard work Dave . Merry Christmas and Happy Hanukkah to you and yours . Peace in 2020 . Andy

Happy Holidays to you too Dave, and to your family and all your loved ones as well ! And thank you so much for your skillful and patient support and for the amazing DXLab Suite. Best DX and 73, Russ,

did you try clicking the "X" (close box) to the right of the text box entry fielsdin the filter window at the bottom of dxkeeper to unfilter the log?

My experience has been that after I log a QSO, the only QSO appearing in my log is the QSO that I just logged. In order to display my full log (including the QSO just recorded) I find it necessary to

I would like to permanently delete the "Auxiliary" and "QSL" fields from the "Log QSO's" tab page of DXKeeper, but even though I uncheck these fields in the DXKeeper "Log QSO's" page and from the

Tom (Win4Icom Author) recommends a winkeyer from K1EL or build your own. I love my winkeyer and it works perfectly with both DXLab and Win4Icom. -- 73 de KF5JRA Ron kf5jra at oneinsane dot org

OK thanks Dave, Glad we sorted this out. I did get WW taking to my RigBlaster through a Com port but although the RB front led was flashing the rig was not keying. I think the RB switching

To answer Dave’s thought about others using it, TR4W uses the CW by serial port feature. I added what I call CWBYCAT to the TR4W contest logger. Mostly Elecraft, late Icom and Kenwood rigs. All done

+ AA6YQ comments below I am running through Win4Icom with a Com0Com virtual com port to my IC 7610 + Win4Icom doesn't convey the "CW Speed" instruction to your radio. I reported this to Tom awhile

I am running through Win4Icom with a Com0Com virtual com port to my IC 7610 Mark N1UK

Thanks, Mark. The errorlog shows that Commander is not receiving a response to the "change CW speed" CAT commands it is sending to your IC-7700, for example: 2019-12-23 22:26:48.707 >

Thanks Dave, I'm pretty sure I have it working well now. Was the port # that I had wrong. Thanks Ron for spotting that. 73 and best Holiday Wishes to all. Sure appreciate your excellent support Dave!

I use WIN4K3Suite with com0com and can run 6 different programs into my K3S My K3 goes into Tom's program as Com5 then I set up 6 pairs 8/9, 10/11, 12/13, 14/15, 16/17 and 18/19 in com0com. For

I sent you the error log 73 Mark N1UK