Joe, To use WSJT-X with Flex, you need to have SSDR CAT, and SSDR DAX installed on the same computer as WSJT-X. The easiest way to install CAT and DAX is to install the whole SSDR

Were you in TAB1 on the main WSJT-X window? There is an issue where the exchange is not captured in WSJT-X if you're not on TAB 1. Neil, KN3ILZ This email has been

Hi Neil, I was on Tab 1, and the exchange is captured automatically in TX Info and RX Info fields in the Contest section in the main QSO Tab.

+ AA6YQ comments below To use WSJT-X with Flex, you need to have SSDR CAT, and SSDR DAX installed on the same computer as WSJT-X. + That's not correct. + As described

+ AA6YQ comments below The antenna selection is indicated in the same query ("I") used to get the frequency and mode. Here is response format, Iabdfg where, a = 1-3, indicates antenna

Thanks to Joe W4TV, "Getting Started with DXLab" now includes this article: https://www.dxlabsuite.com/dxlabwiki/SettingDigitalModeALC 73, Dave, AA6YQ

+ AA6YQ comments below No to both to be honest. It was a last minute decision to stick with what I use (and it was a good decision). I understand that I should have entered my state abbreviation into

Both of the URLs in the message below should reference <https://www.dxlabsuite.com/dxkeeper/Help/Contesting.htm> 73, Dave, AA6YQ + AA6YQ comments below No to both to be honest.

Hi all. I submitted my 2018 marathon sheet successfully. I also set the dxkeeper for 2019, no problem I wanted to go back and use dxkeeper to do some analysis using the 2018 log. Likecwhat would have

+ AA6YQ comments below Hi all. I submitted my 2018 marathon sheet successfully. I also set the dxkeeper for 2019, no problem I wanted to go back and use dxkeeper to do some analysis using the 2018

I thought I had DX Labs, WSJT-x, SmartSDR, DAX all configured to work for FT8 but I guess not. The "DB Scale" in the lower left hand of the WSJT-X screen is showing no signal. Here are some screen

+ AA6YQ comments below I thought I had DX Labs, WSJT-x, SmartSDR, DAX all configured to work for FT8 but I guess not. The "DB Scale" in the lower left hand of the WSJT-X screen is showing no signal.

Dave, I will be glad to test. I'm not sure on the room for selected indicator, but do follow that is is indicated on the radio. I am using Commander remotely is why I asked. Below is my setup, so

+ AA6YQ comments below I will be glad to test. + Did you receive the email message I sent you with the new version of Commander? I'm not sure on the room for selected indicator, but do follow that

For satellite QSOs the following fields are needed (see example below from

Is there a front page for the Wiki thathas an index or search function? I can't seem to find it. Will I need a groups.io password to access it? 73, Eric W3DQ

+ AA6YQ comments below For satellite QSOs the following fields are needed (see example below from

+ AA6YQ Is there a front page for the Wiki thathas an index or search function? + Both are available. I can't seem to find it. + See the first paragraph after the table in the "Goal-oriented

Dave could you attach this link to the help information on the launcher window? I seem to always have a problem finding it when I need it. Julio, W4HY

I am having an issue when running the script I have to check my WAS status on 60 meters. The script I am using is this: filter Band='60m' report us_states <ReportsFolder>us_states_60.txt When I run