Hi Dave. Is it possible to build an interface so that logged QSOs upload to HRDLOG.net? It would need an interface for the username and upload code. Thanks and 73 Greg

Thanks to all who responded to my question. There were quite a number of responses, and they are much appreciated. Looks like Idiom Press and ERC units are pretty popular. Thanks again for the

After all the head scratching, the issue was USB cable related! Andy K3UK

This release - clears the transceiver's Split and Dual receive when a PSK Spot Database Entry is double-clicked with Commander running (tnx to Jack WS3N and Gary AB9M) - includes Two Tone version

This release - properly updates the DXCC award progress of PSK31 spot database entries when a new QSO is logged (tnx to Rich W3ZJ) - includes the spotting station callsign when conveying spots to

I also have a Yaesu G-2800SDX controller sitting on my shelf. It was damaged by lightning but the Idiom Press board in it looks fine. The board worked fined with N1MM and DXView. If anyone is

-----Original Message----- Sent: Saturday, April 13, 2013 5:09 PM To: dxlab@... Subject: [dxlab] Commander config help I am running Win7 64bit DXLabs is installed in C:\DXLab Under

Actually, Yaesu acquired the 2800 from KenPro in the mid 1980's IIRC. I think Yaesu finally re-did the controller. I have a KenPro KR2000 (2800 equivalent) corpse that rattles if shaken - a tornado

-----Original Message----- Sent: Saturday, April 13, 2013 4:59 PM To: dxlab@... Subject: Re: [dxlab] Capture Window - no beam heading? I saw that and followed the instructions, as rfar as

I am running Win7 64bit DXLabs is installed in C:\DXLab Under the General Tab I have K3 selected 'Show by expanding Main window' I have an 'Initial Command Sequence' setup that works Under the

There *is* a zero width field at the far right, titled MarMixedEn when I expand it. However, as soon as a spot comes in it disappears. 73, Pete N4ZR Check out the Reverse Beacon Network

I saw that and followed the instructions, as rfar as I know, but it failed to add it. Tried restarting Spot Collector- no joy. When I look at the Layout panel of the Spot Database display tab in

-----Original Message----- Sent: Saturday, April 13, 2013 4:12 PM To: dxlab@... Subject: [dxlab] DXKeeper 11.0.0 and RST field Hi to all, I notice that it is possible enter alphabetic

I have been using the ERC-M with my Yaesu G-800SA for over a year and love it. Since the G-800SA does not come with an interface for computer, I purchased this one. It did require the relay board but

Hi to all, I notice that it is possible enter alphabetic letters (like AAA, ABC, etc) into 'RST_sent' or 'RST_rcvd' fields....I think that when CW/RTTY mode is selected, the RST field should be

Mike, I've been using the Idiom Press modification for my rotator (yaesu) for nearly 10 years and have only had a problem when a wire got broken on a control lead. I would give it a 5 rating out of a

http://www.easy-rotor-control.com/ I'm currently using several ERC's with pstRotator software. They should work directly with DXView also. An ERC-M should drive your 1000DXA - no relay board

Hi Mike - Yes, DXLabs really makes ham radio more fun! I recently decided to control my Yaesu G-800DXA rotor with DXView, and bought the Idiom Press USB interface. Installation and calibration was

-----Original Message----- Sent: Saturday, April 13, 2013 3:07 PM To: dxlab@... Subject: [dxlab] Rotator-Computer Interface What a fantastic suite of programs for the radio! The more

I'm guessing here that you accidentally collapsed the width of the Azimuth column to zero so that you can no longer see it. It will still show in the layout display that Dave references below. I've