Iain, look again, I have checked only "Unworked", so there would be no more than 64 dots on the map. I'm pursuing mixed DXCC 160-10 and at today I have worked 277 entities, so I want to see the

Ok I have so far in DXK 855 QSO's All are uploded to LOTW, EQsl, etc . Now I do the sync buttons on LOTW with no errors. Now if i click on the button that says Up-Date from LOTW a box pops up asking

-----Original Message----- Sent: Friday, April 05, 2013 5:40 AM To: dxlab@... Subject: [dxlab] Re: SC split spot it. I've just seen another that could perhaps be better. 5W0M spotted

When you have a logged QSO whose address does not print correctly, please 1. create an email message that specifies the QSO's callsign, date, and time 2. place your log file in a zip archive 3.

-----Original Message----- Sent: Friday, April 05, 2013 12:02 PM To: dxlab@... Subject: [dxlab] Problem with DXKeeper using new version of tQSL The new version of tQSL has been working

If you employ DXKeeper's DXCC submission generator, the first thing you'll do is deselect LotW's "proposal" and then select the QSOs identified by DXKeeper. LotW's "proposal" is notoriously

-----Original Message----- Sent: Friday, April 05, 2013 7:32 AM To: Lista DXLab Subject: [dxlab] DXView world map question hello all, all DXLab apps running. I go to DXView and I click the World

-----Original Message----- Sent: Friday, April 05, 2013 5:09 AM To: Lista DXLab Subject: [dxlab] Another question about DXKeeper qsl management hello all, I have noticed the following behaviour when

<salvatore.besso@...> wrote: It's not very intuitive (IMO), but the (full) meaning of "Unconfirmed" is "unconfirmed on any band or mode that you are pursuing for DXCC"... so if you're pursuing

I have run a TS2000 with USB to Serial converter (usually through a hub) for several years. For me, port config: Port 6 <--- this will probably differ for you Baud 9600 Word 8

In message #118365 (May 17),a question was posed about keying a K3 with RTS/DTR in the com port used by ww for communications with the K3, Dave answered: ">>>There's not, John. However, you can

The new version of tQSL has been working fine for the last few days except for the last QSO I tried to upload. From DXKeeper's Log QSOs screen, I right clicked on an entry and chose "Upload to LotW".

Spot on, Joe. Thank you. -Kurt KR2C

Program error 8020 is most often associated with a defective driver for a Prolific based USB to serial adapter. Some Prolific drivers rise the interrupt for "character received" before the character

I had a situation where I needed to delete my com ports on my Win7 PC. I had the PC rediscover the ports without any problems. It seems that all the programs I've checked so far work properly. I'm

Bill and Dave, I got it working last night. Because I didn't save the UDC that was misbehaving, I'm not sure what I was doing wrong, but it might have been the placement of additional IfBand

One suggestion: Check to make sure RTS is set to On in the Commander config. 73, Rich VE3KI

I believe LotW is smart enough. I recall that situation in the past but I'm not sure whether I needed to manually deselect the QSL before I made a LotW submission or not. It should not cost you a

Exactly, Iain . . . it's showing under the selected column on my account on the LoTW web site. By next submission there will be more (hopefully a lot more) and this one will be redundant if it

Hi. This is strange - at least for me. Every time I try to print an address on envelope for an QSO made on Winwarbler using PSKxx the printer does not print the address. I can see something happen