I'm confused about just exactly what the problem is here . I have not had any problems lately with several combinations of Skimmer, an SDR, and DX Lab Suite applications. I should indicate that I

MemSet590 is an Excel program that lets you automatically set up the memories in the Kenwood TS-590S. Once you have defined the memory settings in the spreadsheet, you can then click on the Upload

Just one other point.. it is hard to beat the performance of the CW decoder in Multipsk (with "QRP Decoding" turned on). It works seemlessly with DXK, and Commander. Andy K3UK [Non-text portions of

I ran into a similar problem when I built my new computer with a ASRock 880G motherboard..... no physical LPT. I added a Roswell RC-303 but had difficulty with the parallel port address for Commander

When I extend WinWarbler to decode and display RTTY from a subreceiver or second receiver, I will also extend it to optionally display a waterfall when the Operating Mode is set to CW. I had planned

Just a followup on all the UTC suggestions: Of all of the ones suggested the one by Vic Rosenthal, K2VCO met my needs the best. Nice and big letters, 24hr and UTC. http://www.qsl.net/k2vco/ down

Recently I have not been able to get CW Skimmer to display frequency except when turning the frequency knob of my OMNI-VII. I had it working when I did the

73 Tony Anthony W. DePrato WA4JQS Since Sept 9th 1962 CQ DX HALL OF FAME # 39 DXCC HONOR ROLL FOUNDER SOUTH SANDWICH ISLAND DX GROUP 1988 CALLS HELD VP8BZL VP8SSI 3Y0PI ZD8JQS V31SS WA4JQS/ZS1

That is why I have been advocating lately to get Dave to add a second secondary cat port. Then we can run the SDR software and CW Skimmer without having to use LP-Bridge . In my opinion less is more

QSL_Via like "*W3HNK*" (note quotes and asterisks are both important) 73, ~iain / N6ML

like W3HNK anyone got the filter for this handy thanks 73 Tony Anthony W. DePrato WA4JQS Since Sept 9th 1962 CQ DX HALL OF FAME # 39 DXCC HONOR ROLL FOUNDER SOUTH SANDWICH ISLAND DX GROUP

Tom - Yes, LP Pan is an SDR that gets its signal from the K3 IF just as does the Softrock for K3 IF SDR I use. So you and I have K3 IF input SDRs. I wonder what other SDRs others reading this

How about pskcore.dll it already works but takes a bunch of keystrokes to set it up. I disagree that that the waterfall alone is of no use, I mentioned several uses in my first email. Iv'e never seen

I have a QSL card from VP2MDB in Montserrat (no additional address) The drop-down list 'entity' has both Montserrat DXCC=VP2-M and Spain with DXCC =EA. Am I correct in going with VP2-M?

I'm sure that Dave could make that happen very quickly if you can suggest a *free* CW Decoder/waterfall application that will iconify and communicate the waterfall display and decoded data via

The last thing i need is yet another application using even more if my overburdoned dual monitor screen real estate when WinWarbler could do the job. I don't need a CW decoder all I want is the

Tom, I'm using SDR-IQ and it's working just fine. Since I don't have either LP-Pan or SoftRock I can't confirm correct operation of CW Skimmer in SoftRock-IF mode but with SDR-IQ Skimmer to

I don't know. I am using the LP-Pan adapter which I think in essence serves as the SDR with the only difference being it gets is input from the IF out on the K3. Tom

Tom - I'm using Skimmer with a K3 and an SDR which requires a different setup than using an audio signal from a radio as I understand it. Larry, K4KGG

Joe - Thanks for jumping in. I understand you have this working with a K3. Yes, I saw your post, so on the Skimmer Telnet tab I do have the "Allow SKIMMER commands" box checked. I did not check