Date   
Re: hearing wsjt sigs , but no band activty

Dave AA6YQ
 

+ AA6YQ comments below

Ive been in and out of the hospital twice

+ I'm sorry to hear that, Danny; I hope you're fully recovered.

since was able to last use my digital modes on ts570s/Rigblaster plus, since November and when got home, put on a new CAT cable for one that the the usb serial port had been crushed. Finally got it all corrected today, and now able to get the rig and computer cat control working and able to hear, and see the wsjt waterfall window and also

But, I noticed that I wasnt connecting to qrz.com. For some reason I had to replace my password, before it would work. sigh.

Meanwhile, when I look at the wsjt screen, there appear to be no signals. Lots of parallel lines across it, and occasionally, what appears to be a lot of small vertical lines down at the bottom bu just appears to be noise. No read out of decode signals in the band-activity area. Think I have forgotten more than I thought I knew. Havent had any digital contacts since last September. Am using Lab rig controls as rig in WSJT settings window. So, i went back to WW and tried RTTY signals output, zilch. Please can someone refer me to the online setup and I will start over with WW digital and see if I can get rtty/psk to operate ?

+ All of the setup information is accessible from here:

<https://www.dxlabsuite.com/dxlabwiki/Multimode_Setup>

+ From your description above, I'd check the receiver audio => soundcard connection and configuration first (Windows Mixer, etc.)

73,

Dave, AA6YQ

Re: VFO Display swapping in Commander and causing issue with WSJT

Dave AA6YQ
 

+ AA6YQ comments below

Running a Yaesu FTDX 101MP

+ Thanks, Stuart; I am investigating.

73,

Dave, AA6YQ

Re: Does dxlab upload direct to club log?

Jamie WW3S
 

where in the log book display is the CLublog indicators? I see LOTW and eqsl, but not clublog

------ Original Message ------
From: "Dave AA6YQ" <@AA6YQ>
To: DXLab@groups.io
Sent: 2/19/2020 2:56:29 PM
Subject: Re: [DXLab] Does dxlab upload direct to club log?

+ AA6YQ comments below

thanks....how can i find qsos NOT uploaded to clublog?

+ As documented here,

<https://www.dxlabsuite.com/dxkeeper/Help/Items.htm#Club%20Log>

+ every logged QSO has a "Club Log status" item that indicates its status relative to Club Log.

+ To find QSOs never uploaded to Club Log, filter the Log Page Display with this SQL expression:

App_DXKeeper_ClubLog not in ('Y','M')

73,

Dave, AA6YQ


------ Original Message ------
From: "ND9G Mike" <mike.nd9g@...>
To: DXLab@groups.io
Sent: 2/19/2020 1:59:50 PM
Subject: Re: [DXLab] Does dxlab upload direct to club log?


You can do this is a couple of ways.

1. Bulk uploads: http://www.dxlabsuite.com/dxkeeper/Help/Progress.htm#Club%20Log
2. Automatically as QSOs are logged: http://www.dxlabsuite.com/dxkeeper/Help/QSLConfiguration.htm#Club%20Log%20Tab


You can also right click on a QSO in the log page display, and choose to upload it, but this is not an efficient way to achieve the results.

73,
Mike ND9G


On Wed, Feb 19, 2020 at 12:44 PM Jamie WW3S <ww3s@...> wrote:






<http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient> Virus-free. www.avg.com <http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient>





spot collector and wsjt spotting help

Pat
 

hi all.
  i love my spot collector linking wsjt to my dxkeeper log.
  here is what I am wondering.
  when running.. wsjt will send what it receives to spot collector.. which is ok.
  but I want see the cluster spots and not so much what I am receiving.
  I disable the wsjt link in spot collector then I cant log to dxkeeper.
  hope this make sense.   I don't want to see what I am hearing in spot collector.
  tnx
 Murf 
 n7uvh 
 

hearing wsjt sigs , but no band activty

Danny Douglas <n7dc@...>
 

Ive been in and out of the hospital twice since was able to last use my digital modes on ts570s/Rigblaster plus, since November and when got home, put on a new CAT cable for one that the the usb serial port had been crushed.  Finally got it all corrected today, and now able to get the rig and computer cat control working and able to hear, and see the wsjt waterfall window and also

But, I noticed that I wasnt connecting to qrz.com.  For some reason I had to replace my password, before it would work.  sigh.  

Meanwhile, when I look at the wsjt screen, there appear to be no signals.  Lots of parallel lines across it, and occasionally, what appears to be a lot of small vertical lines down at the bottom bu just appears to be noise.  No read out of decode signals in the band-activity area. Think I have forgotten more than I thought I knew.  Havent had any digital contacts since last September.    Am using Lab rig controls as rig in WSJT settings window.   So, i went back to WW and tried RTTY signals output,  zilch.      Please can someone refer me to the online setup and I will start over with WW digital and see if I can get rtty/psk to operate ?



N7DC@...
Ex WN5QMX,WA5UKR,ET2US,ET3USA,SV0WPP,VS6DD,N7DC/YV5/G5CTB
QSL Bureau, DIRECT, LOTW Preferred, eQSL used but upload at a courtesy only, as do not use the system for awards.

Re: Changing date in DXK

Dave AA6YQ
 

+ AA6YQ comments below

I want to correct the QSO begin date in DXK. I normally just backspace then enter the correct date but for some reason backspace is not working.
What is the fix?

+ In the "Main Log QSOs options" panel on the Configuration window's General tab, do you have the "Require Edit to modify logged QSOs" box checked?

73,

Dave. AA6YQ

Changing date in DXK

Arthur Petteway
 

I want to correct the QSO begin date in DXK.  I normally just backspace then enter the correct date but for some reason backspace is not working.
What is the fix?

73,
Art WB4MNK

Re: Terminate Non-DX Lab Applications

wb6bee
 

I seem to remember you could terminate "some" non-DXLab applications in Windows 7.    Appears not possible in Windows 10, so will quit attempting to do that.

Thanks

Don
WB6BEE

Re: Does dxlab upload direct to club log?

Dave AA6YQ
 

+ AA6YQ comments below

thanks....how can i find qsos NOT uploaded to clublog?

+ As documented here,

<https://www.dxlabsuite.com/dxkeeper/Help/Items.htm#Club%20Log>

+ every logged QSO has a "Club Log status" item that indicates its status relative to Club Log.

+ To find QSOs never uploaded to Club Log, filter the Log Page Display with this SQL expression:

App_DXKeeper_ClubLog not in ('Y','M')

73,

Dave, AA6YQ

------ Original Message ------
From: "ND9G Mike" <mike.nd9g@...>
To: DXLab@groups.io
Sent: 2/19/2020 1:59:50 PM
Subject: Re: [DXLab] Does dxlab upload direct to club log?


You can do this is a couple of ways.

1. Bulk uploads: http://www.dxlabsuite.com/dxkeeper/Help/Progress.htm#Club%20Log
2. Automatically as QSOs are logged: http://www.dxlabsuite.com/dxkeeper/Help/QSLConfiguration.htm#Club%20Log%20Tab


You can also right click on a QSO in the log page display, and choose to upload it, but this is not an efficient way to achieve the results.

73,

Mike ND9G



On Wed, Feb 19, 2020 at 12:44 PM Jamie WW3S <ww3s@...> wrote:







<http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient> Virus-free. www.avg.com <http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient>

Re: Does dxlab upload direct to club log?

Jamie WW3S
 

thanks....how can i find qsos NOT uploaded to clublog? 

------ Original Message ------
From: "ND9G Mike" <mike.nd9g@...>
Sent: 2/19/2020 1:59:50 PM
Subject: Re: [DXLab] Does dxlab upload direct to club log?

You can do this is a couple of ways.



You can also right click on a QSO in the log page display, and choose to upload it, but this is not an efficient way to achieve the results.

73,
Mike ND9G


On Wed, Feb 19, 2020 at 12:44 PM Jamie WW3S <ww3s@...> wrote:




Re: Does dxlab upload direct to club log?

ND9G Mike
 

You can do this is a couple of ways.



You can also right click on a QSO in the log page display, and choose to upload it, but this is not an efficient way to achieve the results.

73,
Mike ND9G


On Wed, Feb 19, 2020 at 12:44 PM Jamie WW3S <ww3s@...> wrote:




Re: Does dxlab upload direct to club log?

Dave K2XR
 

Yes,

Button on the check progress page in  DXKeeper.

Must supply login info in the config section, after that just hit the button anytime.

On 2/19/2020 1:44:20 PM, Jamie WW3S wrote:

Does dxlab upload direct to club log?

Jamie WW3S
 

Re: Terminate Non-DX Lab Applications

Dave AA6YQ
 

+ AA6YQ comments below

Since upgrading from Windows 7 to Windows 10, I have not found the clue to terminating non-DXlab apps in Launcher. The Windows 10 Task Manager doesn't have an "Applications" tab. I have tried various configurations in the Caption window, but no cigar

+ The Launcher can be configured to start non-DXLab applications, but cannot be configured to terminate them. That's because there is no standard way to convey an "initiate graceful shutdown" directive to Windows applications. Each DXLab application accepts a "initiate graceful shutdown" directive, which is how the Launcher instructs them to terminate.

+ Yes, the Launcher could terminate a non-DXLab application by invoking a Windows API that terminates the application's process, but that could cause the application to lose or corrupt data.

73,

Dave, AA6YQ

Re: How to undo what I've done

Dave AA6YQ
 

+ AA6YQ comments below

Yes there is a reason not to upload a QSO, one being some portable operators I know use there home location for all there portable operations even when they are in another state or I just had a casual short QSO with someone local. I keep a record of it but it does not need to go to LOTW.

+ But it does not harm to upload them to LoTW. It is unnecessary for you to avoid an automated solution in order to not upload such QSOs.

I exported an adif file (unfiltered) as a backup to the backup before I try to fix my problem. I noticed that my log has 6238 QSOs but the export only has 6231 QSOs. Where are the 7 Qs and how do I find out what is missing?

+ Was the Log Page Display filtered when you initiated the Export operation?

+ At the bottom of the Main window's "Check Progress" tab, click the Recompute button; this will review every QSO in your log, and mark any that DXKeeper considers "broken". After this operation finishes, click the Broke button in the Filter panel at the bottom of the Main window's "Log QSOs" tab; how many QSOs appear in the Log Page Display?

73,

Dave, AA6YQ

Re: {SPAMFILTER} Re: [DXLab] Help requested.. which 0ld update files can be deleted.

Anthony W. DePrato
 

i always keep the first file which is the main one and the last two files.
73 Tony wa4jqs

Terminate Non-DX Lab Applications

wb6bee
 

Since upgrading from Windows 7 to Windows 10, I have not found the clue to terminating non-DXlab apps in Launcher.   The Windows 10 Task Manager doesn't have an "Applications" tab.   I have tried various configurations in the Caption window, but no cigar

Don
WB6BEE

Re: 2nd database

Jay W8ES
 
Edited

Yes! Thanks, Dave & Mike. I knew there must be a way, but couldn't come up with the proper search terms to find the information.
This is exactly what I wanted to do.
<http://www.dxlabsuite.com/dxlabwiki/MultipleUsers>

I love DXLab.

73,
Jay W8ES

Re: How to undo what I've done

Jeff K6QCB
 

Dave

Yes there is a reason not to upload a QSO, one being some portable operators I know use there home location for all there portable operations even when they are in another state or I just had a casual short QSO with someone local. I keep a record of it but it does not need to go to LOTW.

I exported an adif file (unfiltered) as a backup to the backup before I try to fix my problem. I noticed that my log has 6238 QSOs but the export only has 6231 QSOs. Where are the 7 Qs and how do I find out what is missing?

Jeff K6QCB


On Monday, February 17, 2020, 09:39:37 PM PST, Dave AA6YQ <aa6yq@...> wrote:


+ AA6YQ comments below

Yes I am aware of the DXKeeper to LOTW features. I have gotten used to the way I was doing it. I can pick and choose which QSOs I upload.

+ Is there a reason to not upload them all?

So let me ask this, if I populate the QSL Queue and there is one I don't want to upload can I just uncheck the box in the QSL column and that one will be ignored?

+ Yes:

"Each entry in the QSL Queue contains a QSL box. By default, each entry's box is checked, which enables the entry for QSL Queue operations. A QSL Queue entry whose QSL box is not checked will be ignored by all operations except clearing the QSL Queue. You can use the EnableAll and DisableAll functions to quickly enable or disable all QSL Queue entries. Disabling a QSL Queue entry is useful when you're not yet ready to send a QSL card or label, perhaps because you expect to make additional QSOs with the station and want to print them all on a single card or label."

<https://www.dxlabsuite.com/dxkeeper/Help/QSL.htm#QSL%20Queue%20Operations>

      73,

              Dave, AA6YQ




Re: VFO Display swapping in Commander and causing issue with WSJT

Stuart - VK6MK
 

Running a Yaesu FTDX 101MP