Date   

Re: Kenwood TS-850 and Commander settings

Ed Douglass
 

The IF-232C interface being used is the LCU3-K made by W1GEE.  Made for Kenwood radios.  Software must assert RTS for the TTL interface to receive power.  No other instructions.  Plug 'n play in terms of hardware.  It's the software settings that have to be right for Commander and the TS-850 to "talk".

On Sun, Jul 23, 2017 at 5:52 PM, Ed Douglass <aa9ozham@...> wrote:
Concert just cancelled because of high winds in Sister Bay.  Should have some time this evening to work on my problem.



On Sun, Jul 23, 2017 at 5:13 PM, Ed Douglass <aa9ozham@...> wrote:
Dwight:

DTR:  off
log debugging info: not checked

Still no joy.

Gotta go play with the Peninsula Symphonic Band.  Concert in Sister Bay.

Thanks for the help so far.

On Sun, Jul 23, 2017 at 4:58 PM, dgb ns9i@... [dxlab] <dxlab@...> wrote:
 

dtr on - not

log debug - not



On 7/23/2017 4:42 PM, Ed Douglass aa9ozham@... [dxlab] wrote:
 

Ports tab: Primary CAT Serial Port: COM2, 4800, 8, N, 2, DTR On, RTS On

General Tab: Kenwood, Interrogation checked, 200 ms Command interval, Scan well = 1; Ignore Mousewheel, Use multiple monitors and Log debugging info are checked

VFO A: continues to read 000,000.00. Clicking PTT TX does nothing; changing the TS-850 frequency or mode is not reflected in Commander readout; changing anything on the TS-850 is not reflected in Commander window.

No joy yet.

Sent from Mail for Windows 10

From: ve3iay@... [dxlab]
Sent: Sunday, July 23, 2017 4:29 PM
To: dxlab@...
Subject: Re: [dxlab] Kenwood TS-850 and Commander settings

 

You also need to set RTS on.  See abwiki/TranceiverControlKenwood>.

73,
Rich VE3KI

---In dxlab@..., wrote :

Settings 8 N 2  4800
sometimes you can get them to work with a baud rate of 9600 but go to commander config and select kenwood slow.
73 Tony wa4jqs

At 04:57 PM 7/23/2017, you wrote:

Would someone tell me the correct settings so that my Kenwood TS-850 and Commander will “communicate†with each other?  Using COM2 of a dual COM port card in a PCI slot.  Windows Device Manager says the drivers are up to date and the device is working.  Using a W1GEE TTL device made for the TS-850 that connects between COM2 and the ACC1 port of the TS-850.  This equipment has worked in the past.  Got a better motherboard.  Windows 10 fully updated.  Haven’t found the right permutations and combinations in the Commander Config settings to make  the Commander and the TS-850 “talk†to each other.  (Using COM3 and another W1GEE device for PTT.)  Please help!  Ed
 
Sent from Mail for Windows 10
 

 Virus-free. www.avg.com
Anthony W.DePrato WA4JQS since 1962
CQ DX HALL OF FAME  # 35
DXCC HONOR ROLL
DXPEDITION OF THE YEAR 1992 VP8SSI
DXPEDITION OF THE YEAR 1993/1994 3Y0PI
VP8SSI 3Y0PI VP8BZL V31SS ZD8JQS
 WA4JQS/ZS1 WA4JQS/KC4 WA4JQS/4K1

[Non-text portions of this message have been removed]






Re: Kenwood TS-850 and Commander settings

Ed Douglass
 

Concert just cancelled because of high winds in Sister Bay.  Should have some time this evening to work on my problem.



On Sun, Jul 23, 2017 at 5:13 PM, Ed Douglass <aa9ozham@...> wrote:
Dwight:

DTR:  off
log debugging info: not checked

Still no joy.

Gotta go play with the Peninsula Symphonic Band.  Concert in Sister Bay.

Thanks for the help so far.

On Sun, Jul 23, 2017 at 4:58 PM, dgb ns9i@... [dxlab] <dxlab@...> wrote:
 

dtr on - not

log debug - not



On 7/23/2017 4:42 PM, Ed Douglass aa9ozham@... [dxlab] wrote:
 

Ports tab: Primary CAT Serial Port: COM2, 4800, 8, N, 2, DTR On, RTS On

General Tab: Kenwood, Interrogation checked, 200 ms Command interval, Scan well = 1; Ignore Mousewheel, Use multiple monitors and Log debugging info are checked

VFO A: continues to read 000,000.00. Clicking PTT TX does nothing; changing the TS-850 frequency or mode is not reflected in Commander readout; changing anything on the TS-850 is not reflected in Commander window.

No joy yet.

Sent from Mail for Windows 10

From: ve3iay@... [dxlab]
Sent: Sunday, July 23, 2017 4:29 PM
To: dxlab@...
Subject: Re: [dxlab] Kenwood TS-850 and Commander settings

 

You also need to set RTS on.  See abwiki/TranceiverControlKenwood>.

73,
Rich VE3KI

---In dxlab@..., wrote :

Settings 8 N 2  4800
sometimes you can get them to work with a baud rate of 9600 but go to commander config and select kenwood slow.
73 Tony wa4jqs

At 04:57 PM 7/23/2017, you wrote:

Would someone tell me the correct settings so that my Kenwood TS-850 and Commander will “communicate†with each other?  Using COM2 of a dual COM port card in a PCI slot.  Windows Device Manager says the drivers are up to date and the device is working.  Using a W1GEE TTL device made for the TS-850 that connects between COM2 and the ACC1 port of the TS-850.  This equipment has worked in the past.  Got a better motherboard.  Windows 10 fully updated.  Haven’t found the right permutations and combinations in the Commander Config settings to make  the Commander and the TS-850 “talk†to each other.  (Using COM3 and another W1GEE device for PTT.)  Please help!  Ed
 
Sent from Mail for Windows 10
 

 Virus-free. www.avg.com
Anthony W.DePrato WA4JQS since 1962
CQ DX HALL OF FAME  # 35
DXCC HONOR ROLL
DXPEDITION OF THE YEAR 1992 VP8SSI
DXPEDITION OF THE YEAR 1993/1994 3Y0PI
VP8SSI 3Y0PI VP8BZL V31SS ZD8JQS
 WA4JQS/ZS1 WA4JQS/KC4 WA4JQS/4K1

[Non-text portions of this message have been removed]





Re: SC SQL Filter Error

Dave AA6YQ
 

Thanks for the errorlog.txt file, Mike. It shows that the SQL filter you
have specified on the Audio Alarm tab of SpotCollector's Configuration
window is invalid.

Here's an example:

(CALLSIGN='EA/DL2DXAP') and (FREQUENCY=18085) and (MODE='CW') and
(SPOTTIME=#2017-07-23 10:30:13#) and (k5p)

The last two words "and (k5p)" are what makes it invalid; I suggest that you
remove them.

73,

Dave, AA6YQ


Re: Kenwood TS-850 and Commander settings

Ed Douglass
 

Dwight:

DTR:  off
log debugging info: not checked

Still no joy.

Gotta go play with the Peninsula Symphonic Band.  Concert in Sister Bay.

Thanks for the help so far.

On Sun, Jul 23, 2017 at 4:58 PM, dgb ns9i@... [dxlab] <dxlab@...> wrote:
 

dtr on - not

log debug - not



On 7/23/2017 4:42 PM, Ed Douglass aa9ozham@... [dxlab] wrote:
 

Ports tab: Primary CAT Serial Port: COM2, 4800, 8, N, 2, DTR On, RTS On

General Tab: Kenwood, Interrogation checked, 200 ms Command interval, Scan well = 1; Ignore Mousewheel, Use multiple monitors and Log debugging info are checked

VFO A: continues to read 000,000.00. Clicking PTT TX does nothing; changing the TS-850 frequency or mode is not reflected in Commander readout; changing anything on the TS-850 is not reflected in Commander window.

No joy yet.

Sent from Mail for Windows 10

From: ve3iay@... [dxlab]
Sent: Sunday, July 23, 2017 4:29 PM
To: dxlab@...
Subject: Re: [dxlab] Kenwood TS-850 and Commander settings

 

You also need to set RTS on.  See dxlabwiki/TranceiverControlKenwood>.

73,
Rich VE3KI

---In dxlab@..., wrote :

Settings 8 N 2  4800
sometimes you can get them to work with a baud rate of 9600 but go to commander config and select kenwood slow.
73 Tony wa4jqs

At 04:57 PM 7/23/2017, you wrote:

Would someone tell me the correct settings so that my Kenwood TS-850 and Commander will “communicate†with each other?  Using COM2 of a dual COM port card in a PCI slot.  Windows Device Manager says the drivers are up to date and the device is working.  Using a W1GEE TTL device made for the TS-850 that connects between COM2 and the ACC1 port of the TS-850.  This equipment has worked in the past.  Got a better motherboard.  Windows 10 fully updated.  Haven’t found the right permutations and combinations in the Commander Config settings to make  the Commander and the TS-850 “talk†to each other.  (Using COM3 and another W1GEE device for PTT.)  Please help!  Ed
 
Sent from Mail for Windows 10
 

 Virus-free. www.avg.com
Anthony W.DePrato WA4JQS since 1962
CQ DX HALL OF FAME  # 35
DXCC HONOR ROLL
DXPEDITION OF THE YEAR 1992 VP8SSI
DXPEDITION OF THE YEAR 1993/1994 3Y0PI
VP8SSI 3Y0PI VP8BZL V31SS ZD8JQS
 WA4JQS/ZS1 WA4JQS/KC4 WA4JQS/4K1

[Non-text portions of this message have been removed]




Re: DXView failure to show stateside stations worked-except 6M phone.

Danny Douglas <n7dc@...>
 

>>>I assume that you have the correct log open in DXKeeper. Open DXKeeper's "Realtime Award Tracking" window, select the DXCC tab, and locate the row whose "Prefix" column contains K. Are the status boxes in this row correct? If not, click the Recompute button at the bottom of the Main window's "Check Progress" tab. Does the K row now show the correct status?


-----  I have only one log:   And it is open. 

----- Yes, the K line has a V in all the boxes entity through 2 meters. 

------Went ahead with the Recompute.  Then took another look at RAT and the entries remain all marked with a V in the K prefix

------Took another try at entering K calls in dxView. 

THAT DID THE TRICK.  ALL IS NOW WORKING.   Both, entering calls into DXView manually, and clicking on

SpotCollector  results properly marking the DXView boxes. 


I had done everything yesterday, except the recompute.    


Thanks for the help Dave.  I knew I hadnt lost logs, but it was perplexing. 

Danny





N7DC@...
Ex WN5QMX,WA5UKR,ET2US,ET3USA,SV0WPP,VS6DD,N7DC/YV5/G5CTB
QSL Bureau, DIRECT, LOTW Preferred, eQSL used but upload at a courtesy only, as do not use the system for awards.

On July 22, 2017 at 4:31 PM "'Dave AA6YQ' aa6yq@... [dxlab]" <dxlab@...> wrote:

 

>>>AA6YQ comments below

-----Original Message-----
From: dxlab@... [mailto:dxlab@...]
Sent: Saturday, July 22, 2017 4:21 PM
To: Stephen
Subject: [dxlab] DXView failure to show stateside stations worked-except 6M phone.

woe is me. Last night, just before closing down, I noticed that DXView info screen suddenly is showing only ONE mode/band indicator of having any contacts in the log when I click on a SpotCollector call. . I have a W - in the SSB box, and every other box is blank on all modes and bands. I then clicked on some 50 meters DX calls, and have a normal panel with boxes filled with C and V indications, in all bands and mode. Its only the stateside , click in SPotCollector - or typing a call in the DXView box, that fails to fill the other boxes. They all come up with a W in the 6 M phone box.



73,

Dave, AA6YQ


 


Re: Kenwood TS-850 and Commander settings

NS9I
 

dtr on - not

log debug - not



On 7/23/2017 4:42 PM, Ed Douglass aa9ozham@... [dxlab] wrote:
 

Ports tab: Primary CAT Serial Port: COM2, 4800, 8, N, 2, DTR On, RTS On

General Tab: Kenwood, Interrogation checked, 200 ms Command interval, Scan well = 1; Ignore Mousewheel, Use multiple monitors and Log debugging info are checked

VFO A: continues to read 000,000.00. Clicking PTT TX does nothing; changing the TS-850 frequency or mode is not reflected in Commander readout; changing anything on the TS-850 is not reflected in Commander window.

No joy yet.

Sent from Mail for Windows 10

From: ve3iay@... [dxlab]
Sent: Sunday, July 23, 2017 4:29 PM
To: dxlab@...
Subject: Re: [dxlab] Kenwood TS-850 and Commander settings

 

You also need to set RTS on.  See .

73,
Rich VE3KI

---In dxlab@..., wrote :

Settings 8 N 2  4800
sometimes you can get them to work with a baud rate of 9600 but go to commander config and select kenwood slow.
73 Tony wa4jqs

At 04:57 PM 7/23/2017, you wrote:

Would someone tell me the correct settings so that my Kenwood TS-850 and Commander will “communicate” with each other?  Using COM2 of a dual COM port card in a PCI slot.  Windows Device Manager says the drivers are up to date and the device is working.  Using a W1GEE TTL device made for the TS-850 that connects between COM2 and the ACC1 port of the TS-850.  This equipment has worked in the past.  Got a better motherboard.  Windows 10 fully updated.  Haven’t found the right permutations and combinations in the Commander Config settings to make  the Commander and the TS-850 “talk” to each other.  (Using COM3 and another W1GEE device for PTT.)  Please help!  Ed
 
Sent from Mail for Windows 10
 

 Virus-free. www.avg.com
Anthony W.DePrato WA4JQS since 1962
CQ DX HALL OF FAME  # 35
DXCC HONOR ROLL
DXPEDITION OF THE YEAR 1992 VP8SSI
DXPEDITION OF THE YEAR 1993/1994 3Y0PI
VP8SSI 3Y0PI VP8BZL V31SS ZD8JQS
 WA4JQS/ZS1 WA4JQS/KC4 WA4JQS/4K1





Re: Kenwood TS-850 and Commander settings

Ed Douglass
 

Ports tab: Primary CAT Serial Port: COM2, 4800, 8, N, 2, DTR On, RTS On

General Tab: Kenwood, Interrogation checked, 200 ms Command interval, Scan well = 1; Ignore Mousewheel, Use multiple monitors and Log debugging info are checked

VFO A: continues to read 000,000.00. Clicking PTT TX does nothing; changing the TS-850 frequency or mode is not reflected in Commander readout; changing anything on the TS-850 is not reflected in Commander window.

No joy yet.

Sent from Mail for Windows 10

From: ve3iay@... [dxlab]
Sent: Sunday, July 23, 2017 4:29 PM
To: dxlab@...
Subject: Re: [dxlab] Kenwood TS-850 and Commander settings

 


You also need to set RTS on.  See <http://www.dxlabsuite.com/dxlabwiki/TranceiverControlKenwood>.

73,
Rich VE3KI

---In dxlab@..., <wa4jqs@...> wrote :

Settings 8 N 2  4800
sometimes you can get them to work with a baud rate of 9600 but go to commander config and select kenwood slow.
73 Tony wa4jqs



At 04:57 PM 7/23/2017, you wrote:

Would someone tell me the correct settings so that my Kenwood TS-850 and Commander will “communicate” with each other?  Using COM2 of a dual COM port card in a PCI slot.  Windows Device Manager says the drivers are up to date and the device is working.  Using a W1GEE TTL device made for the TS-850 that connects between COM2 and the ACC1 port of the TS-850.  This equipment has worked in the past.  Got a better motherboard.  Windows 10 fully updated.  Haven’t found the right permutations and combinations in the Commander Config settings to make  the Commander and the TS-850 “talk” to each other.  (Using COM3 and another W1GEE device for PTT.)  Please help!  Ed
 
Sent from Mail for Windows 10
 




 Virus-free. www.avg.com
Anthony W.DePrato WA4JQS since 1962
CQ DX HALL OF FAME  # 35
DXCC HONOR ROLL
DXPEDITION OF THE YEAR 1992 VP8SSI
DXPEDITION OF THE YEAR 1993/1994 3Y0PI
VP8SSI 3Y0PI VP8BZL V31SS ZD8JQS
 WA4JQS/ZS1 WA4JQS/KC4 WA4JQS/4K1




[Non-text portions of this message have been removed]


Re: Kenwood TS-850 and Commander settings

ve3ki
 



You also need to set RTS on.  See <http://www.dxlabsuite.com/dxlabwiki/TranceiverControlKenwood>.

73,
Rich VE3KI

---In dxlab@..., <wa4jqs@...> wrote :


Settings 8 N 2  4800
sometimes you can get them to work with a baud rate of 9600 but go to commander config and select kenwood slow.
73 Tony wa4jqs



At 04:57 PM 7/23/2017, you wrote:


Would someone tell me the correct settings so that my Kenwood TS-850 and Commander will “communicate” with each other?  Using COM2 of a dual COM port card in a PCI slot.  Windows Device Manager says the drivers are up to date and the device is working.  Using a W1GEE TTL device made for the TS-850 that connects between COM2 and the ACC1 port of the TS-850.  This equipment has worked in the past.  Got a better motherboard.  Windows 10 fully updated.  Haven’t found the right permutations and combinations in the Commander Config settings to make  the Commander and the TS-850 “talk” to each other.  (Using COM3 and another W1GEE device for PTT.)  Please help!  Ed
 
Sent from Mail for Windows 10
 




[]  Virus-free. www.avg.com

Anthony W.DePrato WA4JQS since 1962
CQ DX HALL OF FAME  # 35
DXCC HONOR ROLL
DXPEDITION OF THE YEAR 1992 VP8SSI
DXPEDITION OF THE YEAR 1993/1994 3Y0PI
VP8SSI 3Y0PI VP8BZL V31SS ZD8JQS
 WA4JQS/ZS1 WA4JQS/KC4 WA4JQS/4K1


Re: Kenwood TS-850 and Commander settings

Anthony W. DePrato
 


Settings 8 N 2  4800
sometimes you can get them to work with a baud rate of 9600 but go to commander config and select kenwood slow.
73 Tony wa4jqs



At 04:57 PM 7/23/2017, you wrote:


Would someone tell me the correct settings so that my Kenwood TS-850 and Commander will “communicate� with each other?  Using COM2 of a dual COM port card in a PCI slot.  Windows Device Manager says the drivers are up to date and the device is working.  Using a W1GEE TTL device made for the TS-850 that connects between COM2 and the ACC1 port of the TS-850.  This equipment has worked in the past.  Got a better motherboard.  Windows 10 fully updated.  Haven’t found the right permutations and combinations in the Commander Config settings to make  the Commander and the TS-850 “talk� to each other.  (Using COM3 and another W1GEE device for PTT.)  Please help!  Ed
 
Sent from Mail for Windows 10
 




[]  Virus-free. www.avg.com

Anthony W.DePrato WA4JQS since 1962
CQ DX HALL OF FAME  # 35
DXCC HONOR ROLL
DXPEDITION OF THE YEAR 1992 VP8SSI
DXPEDITION OF THE YEAR 1993/1994 3Y0PI
VP8SSI 3Y0PI VP8BZL V31SS ZD8JQS
 WA4JQS/ZS1 WA4JQS/KC4 WA4JQS/4K1


Kenwood TS-850 and Commander settings

Ed Douglass
 

Would someone tell me the correct settings so that my Kenwood TS-850 and Commander will “communicate” with each other?  Using COM2 of a dual COM port card in a PCI slot.  Windows Device Manager says the drivers are up to date and the device is working.  Using a W1GEE TTL device made for the TS-850 that connects between COM2 and the ACC1 port of the TS-850.  This equipment has worked in the past.  Got a better motherboard.  Windows 10 fully updated.  Haven’t found the right permutations and combinations in the Commander Config settings to make  the Commander and the TS-850 “talk” to each other.  (Using COM3 and another W1GEE device for PTT.)  Please help!  Ed

 

Sent from Mail for Windows 10

 


Re: PF and Security Alerts

Richard B Drake
 

I didn't have this on either of my computers but my wife uses Explorer to play some POGO games and she did have it. I downloaded the Adware Removal Tool that Dave references below and it found 193 pieces of Adware on my wife's computer. I removed them all and it seems to be working.
--
73, Rich - W3ZJ
www.w3zj.com

On 7/19/2017 7:19 PM, 'Dave AA6YQ' aa6yq@... [dxlab] wrote:
On my Windows 10 system, clicking the "View Certificate" button in the "Security Alert" window that pops up when I direct Pathfinder to perform a QRZ search shows that the certificate in question is issued to *.btrll.com

Googling btrll lead to this:



      73,

            Dave, AA6YQ


Re: DXView failure to show stateside stations worked-except 6M phone.

Dave AA6YQ
 

AA6YQ comments below
-----Original Message-----
From: dxlab@... [mailto:dxlab@...]
Sent: Saturday, July 22, 2017 4:21 PM
To: Stephen
Subject: [dxlab] DXView failure to show stateside stations worked-except 6M phone.

woe is me. Last night, just before closing down, I noticed that DXView info screen suddenly is showing only ONE mode/band indicator of having any contacts in the log when I click on a SpotCollector call. . I have a W - in the SSB box, and every other box is blank on all modes and bands. I then clicked on some 50 meters DX calls, and have a normal panel with boxes filled with C and V indications, in all bands and mode. Its only the stateside , click in SPotCollector - or typing a call in the DXView box, that fails to fill the other boxes. They all come up with a W in the 6 M phone box.

I assume that you have the correct log open in DXKeeper. Open DXKeeper's "Realtime Award Tracking" window, select the DXCC tab, and locate the row whose "Prefix" column contains K. Are the status boxes in this row correct? If not, click the Recompute button at the bottom of the Main window's "Check Progress" tab. Does the K row now show the correct status?
73,

Dave, AA6YQ


DXView failure to show stateside stations worked-except 6M phone.

Danny Douglas <n7dc@...>
 

woe is me.   Last night, just before closing down, I noticed that DXView info screen suddenly is showing only ONE mode/band indicator of having any contacts in the log when I click on a SpotCollector call. .  I have a W - in the SSB box, and every other box is blank on all modes and bands.     I then clicked on some 50 meters DX calls, and have a normal panel with boxes filled with C and  V  indications, in all bands and mode.    Its only the stateside , click in  SPotCollector - or typing a call in the DXView box, that fails to fill the other boxes.  They all come up with a W in the  6 M phone box.   

Prior to that, I have worked and confirmed with a 9 band WAS on PHONE/CW/DIGI.  Clicking on that W shows up on DXKeeper with 654 SSB total 6 meter contacts.   Looking through the logs, it appears that all my contacts are logged, all DXCC countries (343) and all 50 states (160-10 meters, and on all modes,  are counted, etc.

  No problems, except for DXView.  DXView version 4.3.2 installed.    I do not remember doing anything to DXView recently. to cause a problem there. 


Danny

N7DC@...
Ex WN5QMX,WA5UKR,ET2US,ET3USA,SV0WPP,VS6DD,N7DC/YV5/G5CTB
QSL Bureau, DIRECT, LOTW Preferred, eQSL used but upload at a courtesy only, as do not use the system for awards.


Re: KML file with DXView open

Dave AA6YQ
 

AA6YQ comments below
-----Original Message-----
From: dxlab@... [mailto:dxlab@...]
Sent: Saturday, July 22, 2017 9:01 AM
To: dxlab@...
Subject: [dxlab] KML file with DXView open

Every time i launch DXview I get a popup "How do you want to open this file?" Apparently it has something to do with Google earth. A click anywhere on the desktop makes it disappear and it doesn't seem to cause any trouble - just an irritant.

That means
1. you have DXView configured to open Google Earth and display information on it

2. your Google Earth installation is incomplete or has been broken; specifically, when directed to "open" a .kml file, Windows is not automatically starting Google Earth. You may be able to correct this by re-establishing Windows' "file association" between .kml files and Google Earth.

73,

Dave, AA6YQ


Re: Commander not closing down from Launcher.

Dave AA6YQ
 

The DXLab Launcher directs other DXLab applications to terminate by sending them a message via Windows. If the Launcher isn't able to direct Commander to terminate, but Commander does terminate if you click the X button in its Main window's upper-right corner, the Windows may not be conveying the "terminate" message from the Launcher to Commander. Reboot Windows to see if this corrects the situation.

73,

Dave, AA6YQ

-----Original Message-----
From: dxlab@... [mailto:dxlab@...]
Sent: Saturday, July 22, 2017 8:01 AM
To: dxlab@...
Subject: [dxlab] Re: Commander not closing down from Launcher.



On my windows7 system it is as you describe since long time - it is no problem as I close commander via seperate closing. I feel, it is more a feature as commander is the program, which is needed for other applications and it is for me ok, that is stay open.





________________________________

AVG logo <http://www.avg.com/internet-security> This email has been checked for viruses by AVG antivirus software.
www.avg.com <http://www.avg.com/internet-security>


Re: SC SQL Filter Error

Dave AA6YQ
 

AA6YQ comments below
-----Original Message-----
From: dxlab@... [mailto:dxlab@...]
Sent: Saturday, July 22, 2017 7:14 AM
To: dxlab@...
Subject: [dxlab] SC SQL Filter Error

Generally, when I come into the shack each morning, I have a Spot Collector "SQL Filter Error" message. The various spotting sites
are disconnected. I have to close SC down and restart. All is well until the next morning. As far as I know there are no filters
set. Can anyone give me some advice on what to check?

Please do the following, Mike:
1. on the General tab of SpotCollector's Configuration window, check the "Log debugging info" box

2. terminate SpotCollector

3. start SpotCollector

When you next see the "SQL Filter Error" message,
4. on the General tab of SpotCollector's Configuration window, uncheck the "Log debugging info" box

5. attach the errorlog.txt file from your SpotCollector folder to an email message, and send the message to me via

aa6yq (at) ambersoft.com

Thanks!
73,

Dave, AA6YQ


Re: Convert Cabrillo to ADIF?

Mike - W1MI
 

Maybe ADIFMaster ?

Looks like you’ll need to manually set the ADIF names of each column though.

GL, Mike – AA1AR

 

 

From: dxlab@... [mailto:dxlab@...]
Sent: Saturday, July 22, 2017 10:56 AM
To: dxlab@...
Subject: [dxlab] Convert Cabrillo to ADIF?

 

 

Does anyone know of a program that will convert a Cabrillo file to ADIF?  A friend needs to change one, but not, apparently, with N1MM+.

 

73 & TIA...

 

Phil/VE1BVD

Sydney, Nova Scotia


Convert Cabrillo to ADIF?

Phil & Anne Irons
 

Does anyone know of a program that will convert a Cabrillo file to ADIF?  A friend needs to change one, but not, apparently, with N1MM+.

73 & TIA...

Phil/VE1BVD
Sydney, Nova Scotia


Re: KML file with DXView open

Gene Caldwell
 

Got it!
Cleared Google earth on world map config.


KML file with DXView open

Gene Caldwell
 

Every time i launch DXview I get a popup "How do you want to open this file?"  Apparently it has something to do with Google earth.  A click anywhere on the desktop makes it disappear and it doesn't seem to cause any trouble - just an irritant.

Thanks,

Gene K3GC 

39701 - 39720 of 209586