Date   
Re: New Crosley seat covers

Spock Arnold
 

I think fixitall will be in attendance as will Tim Hamblin.  I doubt that either one will be bringing any finished seat covers. Fixitall is bringing a set of restored seats.  I'm sure both would take orders and have quick turnover.  There is also the possibility of finding used sets in the flea market.
  

On Jun 30, 2019 10:17 PM, "Ron D." <rdole417@...> wrote:
I have a 49 sedan, that the mice destroyed the seat covers and padding. I repainted the frames, and put on new springs. Now I need new covers. I emailed Jerry 6 months ago, with no response. Will anyone be selling new sets at the show? 

Re: New Crosley seat covers

Plandersen
 

Like I said he is slow.  When I get mine together I will send picts.  He even put a real glass window in my convertible top.  Very talented.  Kent

Kent Andersen, YVIAA District Director
PO Box 364
Royal City, WA  99357

Phone 509-346-1500
Fax 509-346-1540
Cell 509-760-5881
Email pkandersen@...





On Jun 30, 2019, at 7:17 PM, Ron D. <rdole417@...> wrote:

I have a 49 sedan, that the mice destroyed the seat covers and padding. I repainted the frames, and put on new springs. Now I need new covers. I emailed Jerry 6 months ago, with no response. Will anyone be selling new sets at the show? 

July Crosley of the Month

Jim Bollman
 

Here is the latest CotM. 

http://crosleyautoclub.com/

Don't forget the Crosley Nationals are coming up real fast in Wauseon Ohio. Hope to see a lot of you next week.

CD Complete Quarters For Sale

Barry Smedley
 

I have a couple of CD complete quarters for sale if anybody is interested They are in very good shape I can bring them to Wauseon.

 

   Barry Smedley

 

From: Crosley-Gang@groups.io [mailto:Crosley-Gang@groups.io] On Behalf Of Jim Bollman
Sent: Sunday, June 30, 2019 11:15 PM
To: Crosley-Gang@groups.io
Subject: [Crosley-Gang] July Crosley of the Month

 

Here is the latest CotM. 

http://crosleyautoclub.com/

Don't forget the Crosley Nationals are coming up real fast in Wauseon Ohio. Hope to see a lot of you next week.

This message contains confidential information intended solely for the use of the addressee(s) named above. Any review, disclosure, distribution, copying or use of the information by others is strictly prohibited. If you have received this message in error, please advise the sender by immediate reply and delete the original message. (English) Ce message contient des informations confidentielles destinées uniquement à l'usage du(des) destinataire(s) nommé(s) ci-dessus. Toute consultation, distribution, copie et utilisation du contenu de ce message est strictement prohibée. Si vous avez reçu ce message par erreur, SVP avisez l'expéditeur par réponse immédiate et effacez le message original. (French)

For Sale: 1950 Crosley CD 18-wheeler

Jim Bollman
 

Fellow Crosley-Gang member's 1950 Crosley 18-wheeler was selected as Hemmings "Find of the Day". Frank, the owner, mentioned on the message board it was for sale back in May but figured I would give it a bump since Hemmings did. Lots of nice pictures and a history of a very unique Crosley.
https://www.hemmings.com/blog/2019/06/30/hemmings-find-of-the-day-1950-crosley-cd-18-wheeler/

Speedometer cable into transmission

Andy Farley
 

Ok, I'm stuck., My speedometer doesn't work and I can't figure out how to remove the speedo cable at the transmission. Initially the speedo jumped then stopped working. Just trying to fix it. 

Re: Speedometer cable into transmission

Barry Smedley
 

Take the cover off of the shifter all you need is a 7/16 wrench, you can get I from underneath also once you get the bolt and clamp off you might have to tug on it a bit.

 

   Barry smedley

 

From: Crosley-Gang@groups.io [mailto:Crosley-Gang@groups.io] On Behalf Of Andy Farley
Sent: Monday, July 01, 2019 12:32 PM
To: Crosley-Gang@groups.io
Subject: [Crosley-Gang] Speedometer cable into transmission

 

Ok, I'm stuck., My speedometer doesn't work and I can't figure out how to remove the speedo cable at the transmission. Initially the speedo jumped then stopped working. Just trying to fix it. 

This message contains confidential information intended solely for the use of the addressee(s) named above. Any review, disclosure, distribution, copying or use of the information by others is strictly prohibited. If you have received this message in error, please advise the sender by immediate reply and delete the original message. (English) Ce message contient des informations confidentielles destinées uniquement à l'usage du(des) destinataire(s) nommé(s) ci-dessus. Toute consultation, distribution, copie et utilisation du contenu de ce message est strictement prohibée. Si vous avez reçu ce message par erreur, SVP avisez l'expéditeur par réponse immédiate et effacez le message original. (French)

Re: Speedometer cable into transmission

Saltsgaver, Mike
 

A jump might mean a bad thing.  Many old speedometers have a brass driven member into which the cable inserts into.  Over time the lubrication dries out and that driven member tries to stick in it’s bore.  The speedo cable will start to wrap up, storing a lot of torsional energy.  If your lucky, the cable breaks…..if not, the brass driven member will finally break free from being stuck and will “over spin” the speedo & will break the shaft onto which the needle is attached.  I’ve had this happen a couple of times on Studebakers & Kaisers.  Both times the speedo put out a loud squeal & the needled jumped around but it broke before I could get pulled off the side of the road.



Hella Electronics Corporation, 43811 Plymouth Oaks Blvd., 48170, Plymouth Michigan
-----------------------------------------------------------------------------------------
This document is to be treated confidentially. Its contents are not to be passed on, duplicated, exploited or disclosed without our express permission. All rights reserved, especially the right to apply for protective rights.

Re: Speedometer cable into transmission

L.E. Hardee
 

The inner speedometer cable removes from the top only.  You disconnect the cable under the dash at the speedometer and just pull the inner cable out.  The outer cable is attached at the transmission by a clamp held on by one bolt.  After removing the outer cable, the speedometer gear can be removed for inspection or replacement.  The inner cable goes back in from the top side under the dash.  My experience was that the inner cable goes in easy until you get to the last few inches.  I had to twist the cable and push repeatedly until I got the right combination for the cable to insert itself into the speedometer gear.  The outer cable has a hard bend near the transmission to miss the car floor.  This is where most cables break.  That was such a problem on the VC's that a guide was added to clamp over the outer cable to maintain a minimum radius to reduce the stress on the inner cable.  A lot of people just drill a hole in the VC transmission hump and route the cable straight up to the back of the speedometer without bending under the floor and going into the engine compartment. 

When you replace the inner cable, most mechanics suggest you only lube the lower 1/3 of it.  If you lube the top of the cable, the excess grease can drip out on your legs as you drive. 


On Mon, Jul 1, 2019 at 12:31 PM Andy Farley <farleya1@...> wrote:
Ok, I'm stuck., My speedometer doesn't work and I can't figure out how to remove the speedo cable at the transmission. Initially the speedo jumped then stopped working. Just trying to fix it. 

Starting Problems in Morning

Bud Martin
 

My 47 sedan has a issue starting in the morning after sitting overnight - It rums well once I do get it started - did a tune-up - it has a spark and when pulling the fuel line it pumps

Any suggestions Bud

Re: Speedometer cable into transmission

Andy Farley
 

So if the inner cable is broken, I'm guessing that you must remove the cable from the transmission to remove the broken piece. Would that be correct?

Re: Speedometer cable into transmission

Jim Bollman
 

Yes, you need to disconnect from both ends to get both pieces out.

On Jul 1, 2019, at 3:40 PM, Andy Farley <farleya1@...> wrote:

So if the inner cable is broken, I'm guessing that you must remove the cable from the transmission to remove the broken piece. Would that be correct?

engine serial number

Mike S
 

I was looking for, but didn't find, a list of the engine serial numbers by year.  The motor in our 48 1/2 is 43151 (w/ cast block).  Any idea when it was made?
Mike S

Re: Speedometer cable into transmission

L.E. Hardee
 

if inner cable is broken, get the top half out from behind the dash and with needle nose pliers, try to pull out the broken piece from the lower end of the cable. 


On Mon, Jul 1, 2019 at 3:46 PM Jim Bollman <Jim@...> wrote:
Yes, you need to disconnect from both ends to get both pieces out.

On Jul 1, 2019, at 3:40 PM, Andy Farley <farleya1@...> wrote:

So if the inner cable is broken, I'm guessing that you must remove the cable from the transmission to remove the broken piece. Would that be correct?

Re: Speedometer cable into transmission

crosleyshortsport
 

Here is a photo of both ends


On Mon, Jul 1, 2019, 6:02 PM L.E. Hardee <hftsales@...> wrote:
if inner cable is broken, get the top half out from behind the dash and with needle nose pliers, try to pull out the broken piece from the lower end of the cable. 

On Mon, Jul 1, 2019 at 3:46 PM Jim Bollman <Jim@...> wrote:
Yes, you need to disconnect from both ends to get both pieces out.

On Jul 1, 2019, at 3:40 PM, Andy Farley <farleya1@...> wrote:

So if the inner cable is broken, I'm guessing that you must remove the cable from the transmission to remove the broken piece. Would that be correct?

Re: engine serial number

Jim Bollman
 

There is no direct date of manufacture vs motor number list that we have found. The range of engine numbers for 1948 were 1/48 to 1/49 - 28804 to 62725. The "New Look" 48 1/2 begins with #CC46175 with the last being around CC-61256 for around 15,000 48 1/2 which was roughly half of the 48 production. So a good guess is engine numbers for 48 1/2 started around engine number 45700 give or take. yours is close if your Crosley is an early 48 1/2 it could be the original engine converted from CoBra to CIBA block. Best we can tell the 48 1/2 production started sometime in June of 1948 even though it was announced earlier.

Confused yet?

Jim...

On Jul 1, 2019, at 5:53 PM, Mike S <miso7@...> wrote:

I was looking for, but didn't find, a list of the engine serial numbers by year.  The motor in our 48 1/2 is 43151 (w/ cast block).  Any idea when it was made?
Mike S

Re: Starting Problems in Morning

crosleyshortsport
 

Bud,  When "cold", if you have a tillotson carb, you must fully choke it to start, and immediatly push the choke in once started. 


On Mon, Jul 1, 2019, 3:36 PM Bud Martin via Groups.Io <bud_martin2001=yahoo.com@groups.io> wrote:
My 47 sedan has a issue starting in the morning after sitting overnight - It rums well once I do get it started - did a tune-up - it has a spark and when pulling the fuel line it pumps

Any suggestions  Bud




Re: Starting Problems in Morning

Jim Bollman
 

On my Tilly I usually full choke till it fires then push into a little less than half choke and hit the starter again if it doesn't catch the next time repeat. It is easy to flood.

On Jul 1, 2019, at 9:19 PM, crosleyshortsport <crosleyshortsport@...> wrote:

Bud,  When "cold", if you have a tillotson carb, you must fully choke it to start, and immediatly push the choke in once started. 

On Mon, Jul 1, 2019, 3:36 PM Bud Martin via Groups.Io <bud_martin2001=yahoo.com@groups.io> wrote:
My 47 sedan has a issue starting in the morning after sitting overnight - It rums well once I do get it started - did a tune-up - it has a spark and when pulling the fuel line it pumps

Any suggestions  Bud





Re: Speedometer cable into transmission

Andy Farley
 

Thank You all very much!

Re: Starting Problems in Morning

PATRICIA GRITTI
 

How to start a Crosley? My engine has a Carter WO carb. When Barry Seel built my engine he rebuilt the carb. All the choke / gas pedal combinations I've tried won't start the engine cold unless I give a squirt of starting fluid. Would someone give a "fix" or the proper starting sequence for the Carter carb?
Don Gritti

On July 1, 2019 at 9:44 PM Jim Bollman <Jim@...> wrote:

On my Tilly I usually full choke till it fires then push into a little less than half choke and hit the starter again if it doesn't catch the next time repeat. It is easy to flood.

On Jul 1, 2019, at 9:19 PM, crosleyshortsport < crosleyshortsport@...> wrote:

Bud,  When "cold", if you have a tillotson carb, you must fully choke it to start, and immediatly push the choke in once started. 

On Mon, Jul 1, 2019, 3:36 PM Bud Martin via Groups.Io <bud_martin2001= yahoo.com@groups.io> wrote:
My 47 sedan has a issue starting in the morning after sitting overnight - It rums well once I do get it started - did a tune-up - it has a spark and when pulling the fuel line it pumps

Any suggestions  Bud