Date   

Crosley military starter

Jon Ciauri
 

I would like to buy a starter for my military engine. The mounting holes are about 4.5 inches center to center. Jon 909 455 6830.


Re: 1947 Pickup

Brett Wright
 

Jim, That is the best kind of success !

Brett Wright


On Mar 23, 2021, at 3:59 PM, Jim Liberty via groups.io <jimliberty356@...> wrote:


Thanks James, being a vintage Porsche guy, I'm not a water guy. Took the radiator there today, and the "Gentleman" there, said, the radiator was recently re-cord. It is only a mile or so from my shop, and now my mind is a rest.  Great heads up.     ........Jim.

On Mon, Mar 22, 2021 at 5:04 PM James Dlapa <crosley1980@...> wrote:

Hi Jim, I know you have been around a awhile, but Harbor Radiator does a nice job. They are in Costa Mesa off Harbor. I typically don’t have them paint them, as the gloss is a bit too much, so do that myself. But should be closes to you. 


On Mon, Mar 22, 2021 at 4:57 PM Jim Liberty <jimliberty356@...> wrote:
Thanks Brett. If I have trouble, I'll take your route.    .......Jim.

On Mon, Mar 22, 2021 at 2:46 PM Brett Wright <bwright@...> wrote:
Jim, 
One option is to have your original radiator re-cored. You really don’t notice  the difference unless you are a  radiator guru. The cost is not low though. $300 or more. The cooling Can be 150% or more improved.

Brett Wright


On Mar 21, 2021, at 8:30 PM, Jim Liberty via groups.io <jimliberty356=gmail.com@groups.io> wrote:


Have any of you replaced your radiator. If so brand and model if you have it. ........................Jim.


Re: 1947 Pickup

James Dlapa
 


I’m glad it worked out. I have always had great service there. 

On Tue, Mar 23, 2021 at 12:59 PM Jim Liberty <jimliberty356@...> wrote:
Thanks James, being a vintage Porsche guy, I'm not a water guy. Took the radiator there today, and the "Gentleman" there, said, the radiator was recently re-cord. It is only a mile or so from my shop, and now my mind is a rest.  Great heads up.     ........Jim.

On Mon, Mar 22, 2021 at 5:04 PM James Dlapa <crosley1980@...> wrote:

Hi Jim, I know you have been around a awhile, but Harbor Radiator does a nice job. They are in Costa Mesa off Harbor. I typically don’t have them paint them, as the gloss is a bit too much, so do that myself. But should be closes to you. 


On Mon, Mar 22, 2021 at 4:57 PM Jim Liberty <jimliberty356@...> wrote:
Thanks Brett. If I have trouble, I'll take your route.    .......Jim.

On Mon, Mar 22, 2021 at 2:46 PM Brett Wright <bwright@...> wrote:
Jim, 
One option is to have your original radiator re-cored. You really don’t notice  the difference unless you are a  radiator guru. The cost is not low though. $300 or more. The cooling Can be 150% or more improved.

Brett Wright


On Mar 21, 2021, at 8:30 PM, Jim Liberty via groups.io <jimliberty356=gmail.com@groups.io> wrote:


Have any of you replaced your radiator. If so brand and model if you have it. ........................Jim.


Re: 1947 Pickup

Jim Liberty
 

Thanks James, being a vintage Porsche guy, I'm not a water guy. Took the radiator there today, and the "Gentleman" there, said, the radiator was recently re-cord. It is only a mile or so from my shop, and now my mind is a rest.  Great heads up.     ........Jim.

On Mon, Mar 22, 2021 at 5:04 PM James Dlapa <crosley1980@...> wrote:

Hi Jim, I know you have been around a awhile, but Harbor Radiator does a nice job. They are in Costa Mesa off Harbor. I typically don’t have them paint them, as the gloss is a bit too much, so do that myself. But should be closes to you. 


On Mon, Mar 22, 2021 at 4:57 PM Jim Liberty <jimliberty356@...> wrote:
Thanks Brett. If I have trouble, I'll take your route.    .......Jim.

On Mon, Mar 22, 2021 at 2:46 PM Brett Wright <bwright@...> wrote:
Jim, 
One option is to have your original radiator re-cored. You really don’t notice  the difference unless you are a  radiator guru. The cost is not low though. $300 or more. The cooling Can be 150% or more improved.

Brett Wright


On Mar 21, 2021, at 8:30 PM, Jim Liberty via groups.io <jimliberty356=gmail.com@groups.io> wrote:


Have any of you replaced your radiator. If so brand and model if you have it. ........................Jim.


Re: CC Crosley Hood Latch

Jim Aschliman
 

Great teamwork!


Re: Carter Carbureter

Butch
 

Mac,

It goes in the lower hole.

Butch

On 3/22/2021 4:04 PM, Mac McBrayer wrote:
Installing a carbureter kit , which hole does the pump link go in ?  It was in the upper when off car.  Mac  ( was not running well before)
--
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus


Re: 1947 Pickup

James Dlapa
 


Hi Jim, I know you have been around a awhile, but Harbor Radiator does a nice job. They are in Costa Mesa off Harbor. I typically don’t have them paint them, as the gloss is a bit too much, so do that myself. But should be closes to you. 


On Mon, Mar 22, 2021 at 4:57 PM Jim Liberty <jimliberty356@...> wrote:
Thanks Brett. If I have trouble, I'll take your route.    .......Jim.

On Mon, Mar 22, 2021 at 2:46 PM Brett Wright <bwright@...> wrote:
Jim, 
One option is to have your original radiator re-cored. You really don’t notice  the difference unless you are a  radiator guru. The cost is not low though. $300 or more. The cooling Can be 150% or more improved.

Brett Wright


On Mar 21, 2021, at 8:30 PM, Jim Liberty via groups.io <jimliberty356=gmail.com@groups.io> wrote:


Have any of you replaced your radiator. If so brand and model if you have it. ........................Jim.


Re: 1947 Pickup

Jim Liberty
 

Thanks Brett. If I have trouble, I'll take your route.    .......Jim.

On Mon, Mar 22, 2021 at 2:46 PM Brett Wright <bwright@...> wrote:
Jim, 
One option is to have your original radiator re-cored. You really don’t notice  the difference unless you are a  radiator guru. The cost is not low though. $300 or more. The cooling Can be 150% or more improved.

Brett Wright


On Mar 21, 2021, at 8:30 PM, Jim Liberty via groups.io <jimliberty356=gmail.com@groups.io> wrote:


Have any of you replaced your radiator. If so brand and model if you have it. ........................Jim.


Re: 1947 Pickup

Dennis Terdy
 

Jim,

I have had 2 recored, and they work perfectly. (Not cheap - like Brett said.) One shop claimed the "soldering was bad at the top" and wanted nothing to do with it. I just went to another vendor, and it's been two years without a problem and a cool running '47 coupe. 

Dennis

On Mon, Mar 22, 2021 at 4:46 PM Brett Wright <bwright@...> wrote:
Jim, 
One option is to have your original radiator re-cored. You really don’t notice  the difference unless you are a  radiator guru. The cost is not low though. $300 or more. The cooling Can be 150% or more improved.

Brett Wright


On Mar 21, 2021, at 8:30 PM, Jim Liberty via groups.io <jimliberty356=gmail.com@groups.io> wrote:


Have any of you replaced your radiator. If so brand and model if you have it. ........................Jim.



--
Dennis Terdy


Re: 1947 Pickup

Brett Wright
 

Jim, 
One option is to have your original radiator re-cored. You really don’t notice  the difference unless you are a  radiator guru. The cost is not low though. $300 or more. The cooling Can be 150% or more improved.

Brett Wright


On Mar 21, 2021, at 8:30 PM, Jim Liberty via groups.io <jimliberty356@...> wrote:


Have any of you replaced your radiator. If so brand and model if you have it. ........................Jim.


Carter Carbureter

Mac McBrayer
 

Installing a carbureter kit , which hole does the pump link go in ?  It was in the upper when off car.  Mac  ( was not running well before)


Re: Lumber Wagon

Jim Liberty
 

I'm going to do just that on my '47 PU.    ......Jim.

On Mon, Mar 22, 2021 at 9:18 AM David Stubenvoll <David.Stubenvoll@...> wrote:
Since the only thing that I ever used the backseat In my ‘49 wagon for was piling stuff on, I decided to remove it. Then it really didn’t look right because of the seat well so I spent yesterday building an oak bed. The front lays on the high part of the floor pan, the middle straddles the stiffening rib to keep it in place, and the rear is up a couple inches to make it look level. The boards are 7/16 thick to save weight but with three points of contact it’s very sturdy. Now I have plenty of room for lawn chairs, cooler, and that gotta have it impossible find if the car show has a swap meet.

Attachments:


Re: CC Crosley Hood Latch

Jim Liberty
 

Thanks Paula, great information.    .....Jim.

On Sun, Mar 21, 2021 at 7:08 PM Paula W <paula_whitney@...> wrote:

Here are the final pictures. Please let me know if I should be putting these elsewhere. Basically, I included what I'd want if just starting out. BTW, my set up did not have an "unlocking wire assembly pin and top (a cotter pin)" as mentioned in the manual; just the hex with the set screw.

I owe a huge debt to Dave Edwards and his drawings, both the original in this thread and the one he provided me on the invoice for my replacement springs (included). Thank you Dave!!! I NEVER would have guessed otherwise how to hook the springs to the body. The tiny hole was invisible under dirt and grease and the square cut-out looks just like a...well...square cut-out.

In the picture of my final assembly I don't have the hood release cable attached, however you can see it waiting its turn in the background. That installation came over an hour or more later when I discovered I had to get a cross panel on first. By that time I was not thinking about pictures.

I think I got it right, or close enough. :-)

Attachments:


Lumber Wagon

David Stubenvoll
 

Since the only thing that I ever used the backseat In my ‘49 wagon for was piling stuff on, I decided to remove it. Then it really didn’t look right because of the seat well so I spent yesterday building an oak bed. The front lays on the high part of the floor pan, the middle straddles the stiffening rib to keep it in place, and the rear is up a couple inches to make it look level. The boards are 7/16 thick to save weight but with three points of contact it’s very sturdy. Now I have plenty of room for lawn chairs, cooler, and that gotta have it impossible find if the car show has a swap meet.


Re: CC Crosley Hood Latch

Paula W
 

Here are the final pictures. Please let me know if I should be putting these elsewhere. Basically, I included what I'd want if just starting out. BTW, my set up did not have an "unlocking wire assembly pin and top (a cotter pin)" as mentioned in the manual; just the hex with the set screw.

I owe a huge debt to Dave Edwards and his drawings, both the original in this thread and the one he provided me on the invoice for my replacement springs (included). Thank you Dave!!! I NEVER would have guessed otherwise how to hook the springs to the body. The tiny hole was invisible under dirt and grease and the square cut-out looks just like a...well...square cut-out.

In the picture of my final assembly I don't have the hood release cable attached, however you can see it waiting its turn in the background. That installation came over an hour or more later when I discovered I had to get a cross panel on first. By that time I was not thinking about pictures.

I think I got it right, or close enough. :-)


1947 Pickup

Jim Liberty
 

Have any of you replaced your radiator. If so brand and model if you have it. ........................Jim.


Carbs

Jim Liberty
 

Hi Ed, and gang, would you have pictures of the linkage for the dual carb. set up. The motor got a new steel crank, and a good clean up. Dual exhaust with a "Cherry Bomb" muffler.         

                                                                                        ................Thanks, all for your help  ................Jim.


Re: FOR rear drum photos

Jim Liberty
 

Does anyone out there have an oil canister complete with bracket for my 1947 pickup.    .....Jim.

On Sat, Mar 20, 2021 at 4:48 AM Brian Dlapa via groups.io <treestumpbvd=yahoo.com@groups.io> wrote:
ok thanks

On Friday, March 19, 2021, 11:31:47 AM CDT, jeff <jeffalyon@...> wrote:


Brian, I think Steve will buy it.  Will let you know if it is still available next week. 

Jeff



Sent from my jphone


-------- Original message --------
From: "Brian Dlapa via groups.io" <treestumpbvd=yahoo.com@groups.io>
Date: 3/19/21 9:00 AM (GMT-08:00)
Subject: Re: [Crosley-Gang] FOR rear drum photos

im interested

On Friday, March 19, 2021, 10:16:56 AM CDT, Steve Olinger <olinger@...> wrote:


Hi Jeff,
        What are you asking for it? My email is olinger@...
Thanks
Steve




On Fri, 19 Mar, 2021 at 10:58 AM, jeff <jeffalyon@...> wrote:
 
Steve, not yet.  It is still available. 

Jeff



Sent from my jphone


-------- Original message --------
From: "Steve Olinger via groups.io" <solinger=rockingham.k12.va.us@groups.io>
Date: 3/19/21 6:34 AM (GMT-08:00)
Subject: Re: [Crosley-Gang] FOR rear drum photos

Hi Jeff,
          Have you sold the rear drum? Thanks Steve


Re: FOR rear drum photos

Brian Dlapa
 

ok thanks

On Friday, March 19, 2021, 11:31:47 AM CDT, jeff <jeffalyon@...> wrote:


Brian, I think Steve will buy it.  Will let you know if it is still available next week. 

Jeff



Sent from my jphone


-------- Original message --------
From: "Brian Dlapa via groups.io" <treestumpbvd@...>
Date: 3/19/21 9:00 AM (GMT-08:00)
To: Crosley-Gang@groups.io
Subject: Re: [Crosley-Gang] FOR rear drum photos

im interested

On Friday, March 19, 2021, 10:16:56 AM CDT, Steve Olinger <olinger@...> wrote:


Hi Jeff,
        What are you asking for it? My email is olinger@...
Thanks
Steve




On Fri, 19 Mar, 2021 at 10:58 AM, jeff <jeffalyon@...> wrote:
 
To: crosley-gang@groups.io
Steve, not yet.  It is still available. 

Jeff



Sent from my jphone


-------- Original message --------
From: "Steve Olinger via groups.io" <solinger=rockingham.k12.va.us@groups.io>
Date: 3/19/21 6:34 AM (GMT-08:00)
Subject: Re: [Crosley-Gang] FOR rear drum photos

Hi Jeff,
          Have you sold the rear drum? Thanks Steve


Re: FOR rear drum photos

jeff <jeffalyon@...>
 

Brian, I think Steve will buy it.  Will let you know if it is still available next week. 

Jeff



Sent from my jphone


-------- Original message --------
From: "Brian Dlapa via groups.io" <treestumpbvd@...>
Date: 3/19/21 9:00 AM (GMT-08:00)
To: Crosley-Gang@groups.io
Subject: Re: [Crosley-Gang] FOR rear drum photos

im interested

On Friday, March 19, 2021, 10:16:56 AM CDT, Steve Olinger <olinger@...> wrote:


Hi Jeff,
        What are you asking for it? My email is olinger@...
Thanks
Steve




On Fri, 19 Mar, 2021 at 10:58 AM, jeff <jeffalyon@...> wrote:
 
To: crosley-gang@groups.io
Steve, not yet.  It is still available. 

Jeff



Sent from my jphone


-------- Original message --------
From: "Steve Olinger via groups.io" <solinger=rockingham.k12.va.us@groups.io>
Date: 3/19/21 6:34 AM (GMT-08:00)
Subject: Re: [Crosley-Gang] FOR rear drum photos

Hi Jeff,
          Have you sold the rear drum? Thanks Steve

1541 - 1560 of 40805