|
Re: Crosley Welder - for trade
Still looking for someone who needs this welder!
|
|
|
|
Radiator
Sandy Smith
In need of a radiator for 1951 CD
original rad went in for repair and top tank split and not repairable, purchased a rad at the meet, core was bad but tank was looking good. Just found out that tank too split when removing it. So I am back to looking for a good rad, bigger problem is need a seller who would be willing pack and ship to Canada. Sandy Smith Arkell, Ontario, Canada
|
|
|
|
Re: Speaking of Wipers...
Spock Arnold
Did you try switching them from side to side. Perhaps you have the angle wrong On the other wiper motor.
On Jul 31, 2019 4:18 PM, Mike S <miso7@...> wrote: The wiper arm on the passenger side of our car was very weak regarding the tension that holds the blade against the glass (in fact, it is floppy loose). I purchased a new set of arms from Dave Edwards at the meet and after a few minutes of studying the way they mount (never been around this style before), was able to take the old one off and put the new one on.....however, the new one is just as loose as the old one, even though the spring is a little longer on the new one. The drivers side appears to be assembled the same way, but it's tension is just fine. What am I missing?
|
|
|
|
Speaking of Wipers...
Mike S
The wiper arm on the passenger side of our car was very weak regarding the tension that holds the blade against the glass (in fact, it is floppy loose). I purchased a new set of arms from Dave Edwards at the meet and after a few minutes of studying the way they mount (never been around this style before), was able to take the old one off and put the new one on.....however, the new one is just as loose as the old one, even though the spring is a little longer on the new one. The drivers side appears to be assembled the same way, but it's tension is just fine. What am I missing?
|
|
|
|
Re: Wipers.
Saltsgaver, Mike
The shaft that goes thru the body is a little larger on the Jeep motors, so the hole in the body might have to be opened up. Also, the length of the shafts are longer than the ones on the vacuum motors. You might have to cut them off to make sure you have enough clearance between the motor and the instrument cluster. They aren’t hard to cut off….I have them on my Kubelwagen & I also had to shorten the shafts. Mike S Hella Electronics Corporation, 43811 Plymouth Oaks Blvd., 48170, Plymouth Michigan ----------------------------------------------------------------------------------------- This document is to be treated confidentially. Its contents are not to be passed on, duplicated, exploited or disclosed without our express permission. All rights reserved, especially the right to apply for protective rights.
|
|
|
|
Re: Wipers.
Here's one from Mac's https://www.macsautoparts.com/early_v8_ford_truck/electric-windshield-wiper-motor-6-volt-replacement-type-stainless-steel-ford-382726.html
|
|
|
|
Re: Wipers.
Just google 6 volt Jeep wiper motors. The older Jeeps were 6 volt.The ones I have seen will just about bolt on.
|
|
|
|
Re: radio antenna wire
dale@servicemotors.net
We here at service motors don't have just the cable but we do have a complete new antenna!!
toggle quoted messageShow quoted text
On Jul 30, 2019, at 11:14 AM, olinger@... wrote:
|
|
|
|
Re: radio antenna wire
Mike, I have what is left of an original antenna from a 51 Crosley and one of the newer ones that people have been using as a replacement for the last 40 years or so. Yours looks like the replacement type and you shouldn't have any trouble finding a replacement cable. The original has the same diameter fitting but slightly course thread and instead of male connector on the antenna it is a female.
toggle quoted messageShow quoted text
Jim...
|
|
|
|
Farm O Road for sale
Pat Curran
I have a 1952 Crosley Farm O Road for sale. AACA National First Prize winner in 1988, Green with tan seats, dual rear wheels, front and rear PTO’s, several original implements. $19,900, Photos and more info on request at racin@...
|
|
|
|
Re: radio antenna wire
Steve Olinger
I believe what I have will work. Send a email to olinger@...
|
|
|
|
Re: radio antenna wire
Mike S
The outer portion is 1/2" diameter with fine threads. The little post inside measures .095".
|
|
|
|
Re: radio antenna wire
You might give Bill a call. He rebuilds radios and might be a good resource https://www.billtheradioguy.com/
|
|
|
|
Re: radio antenna wire
Steve Olinger
On the modern twin post antenna there is a couple different size studs they thread on. Try to check the thread size as I may have a couple.
Steve
|
|
|
|
Re: radio antenna wire
Andy Farley
We can't be the only people who need just the antenna cable. Is there anything Service Motors can do for us?
|
|
|
|
Re: radio antenna wire
Andy Farley
Ditto. I also need an antenna cable. I also have a good antenna but no cable. Does anyone know where we can get just the cable?
|
|
|
|
Re: radio antenna wire
Saltsgaver, Mike
I already have a nice antenna….just no cable. I thought I’d ask around before buying a whole new set up. Mike S Hella Electronics Corporation, 43811 Plymouth Oaks Blvd., 48170, Plymouth Michigan ----------------------------------------------------------------------------------------- This document is to be treated confidentially. Its contents are not to be passed on, duplicated, exploited or disclosed without our express permission. All rights reserved, especially the right to apply for protective rights.
|
|
|
|
Re: radio antenna wire
crosleyshortsport
I may be wrong, though I believe you can use a new cable from a new antenna
On Mon, Jul 29, 2019, 1:14 PM Mike S <miso7@...> wrote: I am in need of the cable that goes between the antenna and the radio in our 48 wagon. Anyone have a broken antenna laying around that they would sell the cable off of?
|
|
|
|
radio antenna wire
Mike S
I am in need of the cable that goes between the antenna and the radio in our 48 wagon. Anyone have a broken antenna laying around that they would sell the cable off of?
thanks, Mike S
|
|
|
|
Re: Crosley Welder - for trade
About 300 miles
toggle quoted messageShow quoted text
Give me a call at 360 801-5251 Jerry
----- Original Message -----
From: Mike Mayberry <mikemayberry75@gmail.com> To: Crosley-Gang@groups.io Sent: Fri, 26 Jul 2019 14:41:34 -0400 (EDT) Subject: Re: [Crosley-Gang] Crosley Welder - for trade I would love to have it! I have family in spokane how far are you from there?
|
|
|