I recently bought a v5 un-assembled. After a few days of assembly I immediately updated the firmware to CEC 1.2. Now when I power the radio is quickly displays what seems to be 2 software versions lik

Hi all I have a v4 uBITX that has developed a fault. The symptoms are very low received audio and the receiver seems to be very deaf ! My fault find so far has indicated that the frequencies on the mi

Good morning. Does anyone know whether any of these displays are suitable for the μBITX and whether the CEC firmware is suitable for them? Thanks ans regards Lawrence https://www.banggood.com/2_8-Inch

I'm playing around with my uBITX v6 for the first time and trying to get digital modes working. I'm trying to get WSJT-X working as an initial test that I have everything up and running. The USB contr

I received my μBITX V6 this week while I was on a biz trip and assembled it on Friday evening. The total assembly time was under 2 hours, if I did it a second time it would be about an hour or less. (

Hi Reed, The operation of keying has improved but I now find when it goes into TX using the PTT on the mic connector it either is seriously delayed in returning to full sens receive mode. It also occu

Does anyone out there have 2 extra/surplus 680nH 1210 inductor EPCOS TDK MURATA parts available for sale. I did the Axicom relay mod and would like to finish up with the addition of the two inductors

Peeps, I have done a bit of tweaking to the code of the version 6. the updated code is at https://github.com/afarhan/ubitxv6/ Here is what is new: 1. The 17 meters band now works, it was an oversight

going to fit a sotabeams cw filter to my ubitx v5 ,where can i insert this on the board (before lm386 amp) if any one has done this what tracks will i need to break into as i would ike to fit inside t

When put into SWR mode connected to an antenna and the uBITxV6 it just cause the Receiver to go into an oscillation and does not measure anything. Locks up the receiver as well. Seems to measure PWR O

Hi I’m a newbie although licensed since 1973 .. are these the all band rigs .. if so I’ll buy one Wa6YCA

In looking over my board, trying to trouble shoot the low output on 40m, I see that C210 and C216 are missing from the board, and they are assigned a value of Zero on the schematic, so I'm assuming th

Bruce, I was in error. Rechecked the battery voltage tonight and it is 9.45 v with the new batteries. I thought it had only 4 AA batteries in the internal battery holder but on second look there are 6

For those of you that have built, building or planning to build TSW's Teensy 4 to NANO adapter to replace the NANO on your V6 uBITX, We just put the latest and greatest of our T4 software on the www.w

soldersmoke dot blogspot dot com or SolderSmoke Podcast #217 -- Beach trip, '30s station, uBITX mods, HRO RX AM, ELMAC, Teensy, MAILBAG SolderSmoke Podcast #217 -- Beach trip, '30s station, uBITX mods

Are they shipping? Site still say pre order, to ship jan 20 which is about ten days ago. Also will they come with the sped up software? tnx jerry aa1of

Hey guys, I'm looking to get some 2N2222A transistors for my uBITX mods. Does the following appear a trustworthy source? 2N2222A - Bipolar (BJT) Single Transistor, NPN, 40 V, 300 MHz, 1.2 W, 800 mA, 1

My power supply regulator failed. The crowbar circuit kicked in at 15v and blew the fast blow fuse, but my board is dead. The voltage could have gotten as high as 27v before the fuse blew. The 2 amp f

(I think Thomas from HF Signals is most active on the group recently (and Farhan! )) Thank you, I had a pleasant surprise on arrival home last night. My order 24653 had arrived, Ordered 10th January a

Hello, I should be getting my new v6 today (sitting at my parents house, keeps the porch pirates away) and I would like to put fuses on the main power lines into the radio. I was wondering what was th