This has been my attempt with VU3SUA's kit. I believe they are working on a case of V6, the existing cases can be used to upgrade.

Thanks Evan. You are spot on the side band change...still getting used to the new firmware. Just realised that in the morning. I will try with the 11055600 and see how it sounds too...yes, frequency c

#nextion #v6 #ubitx #ubitxv6

After trying out the steps, I think I have arrived at a good value for 40m which is 210000 and 110570500. But the problem is this setting completely makes the 20m sound bad. If I adjust 20m, then 40m

#nextion #v6 #ubitx #ubitxv6

Thanks. I had not seen the menu options for Calibration in KD8CEC builds...And I had not set the code to V5...You were right now both counts...now trying to get the best possible voice... Thanks !

#nextion #v6 #ubitx #ubitxv6

Would love to have this for a Nextion 3.5

#arduino #fft #firmware #nextion #smeter

Hi, Trying to upgrade my uBitx v6 to a 3.5" Nextion display. 1. Got the latest build from https://github.com/phdlee/ubitx/releases/tag/v1.20 and updated the raduino. 2. Found a good build (I hope) for

#nextion #v6 #ubitx #ubitxv6

Thanks much. Any idea what the CW-1 and CW-2 are for?

#ubitxv6 #ubitx-help

Has anyone integrated uBitx V6 board with the kit from https://amateurradiokits.in/. Since the power /volume control, ptt, audio out and cw key along with Antenna connectors are soldered on the board

#ubitxv6 #nextion

AFAIK, P1 is power P2 is Antenna P3 is ??? P4 is Speaker P5 is ??? Also, 1. if we use P2 should we remove the BNC soldered? 2. Should we remove the On off/Volume connector if we use P1? Any help is ap

#ubitxv6 #ubitx-help

Yeah, the pictures are not very helpful. So far, I have got the all peripheral boards soldered except audio amp. Will start with once I buy LA4225. It was missing. Then I will have to figure out power

No, have the same questions you are having. So monitoring this for solutions. Am also rebuilding ubitx v6 with nextion

Watching this...

Checked. CW is just fine. How do I avoid audio overdrive?

#ubitxv6 #antennas

Thanks. No, my uBitx case isnt grounded. I will fix that. I will also try a Balun. Thanks.

#ubitxv6 #antennas

Added a 20m antenna to my Inverted V already having 40m. Now, I have 7150 in VFO:A and 14220 in VFO:B. When I give a TX, it will switch over to VFO:A in the middle of TX... If I have 14220 in VFO:A, i

#ubitxv6 #antennas

I need one too.. -VU3GWN

#ubitx #filters #parts

I have brushless fans that I can use. But am worried about RF interference from the fan. What kind of fan should I use?

Thanks Shyam...some more changes are in process including the CW shift issue. Hopefully by this weekend, I will be able to upload it.

#bfo #calibration #firmware #ubitxv6

Thanks much guys for the info on getting closer to having a working FT8 TX....I will gladly report back when I have something ... Thanks again, Handle : Guru Callsign : VU3GWN

#bfo #calibration #firmware #ubitxv6

Hey Ted, Guess I was wrong about K8DCEC...since I don't have a Nextion display yet, haven't tried that yet...so let's see what the future holds... With respect to FT8, my current setup is CAT connecte

#bfo #calibration #firmware #ubitxv6