I'll close it out. Although fldigi could not "see" the radio, flrig can read and write so I can control the radio from this computer. I set fldigi to use flrig as the front end and it works. I still h

#ubitx #digital #cat

Bruce, Glad we could help. Always feel free to post to a new topic with any questions. The more information you can provide the easier it is for us to help. You can also post back to this topic as wel

#ubitx #digital #cat

I think you nailed it on the DTR setting. I got a fresh load of flrig (via a PPA) and in the Configuration window clicked off DTR. I was then able to change the frequency, the mode, switch VFOs, etc.

#ubitx #digital #cat

Bruce, Like Doug, I do not use Linux or iOS with either of the fl programs you listed, so cannot comment on your specific error messages (though most of the time they are permission issues in Linux sy

#ubitx #digital #cat

Thanks for the responses. Latest tests: run rigctl from Terminal on both the Pi and Linux computers. Here's the example on the Linux laptop with the Pi result about identical: ~$ rigctl -m 122 -r /dev

#ubitx #digital #cat

Bruce, I am running the same firmware on a v3 µBITX as well. I do not use any of the programs you mention but I leave my rig on 24/7 when weather allows as a WSPR rx. Here are my settings in WSJT-X ru

#ubitx #digital #cat

Assuming that since your are using a Pi, that it is probably running some version of Linux. Go to the command prompt and enter "su"...it will ask for the root password and then change to the "root" pr

#ubitx #digital #cat

Correction: CQRLog does track ("read") the frequency and mode of the uBitX when configured as a Yaesu FT-857 on the Pi. This is all pretty weird!

#ubitx #digital #cat

I installed CEC V1.20 firmware on a uBitX v3. The improvements were great. Even RX seems improved. What doesn't work is CAT. I've attempted flrig control on both a Raspberry Pi (with HamPi) and a lapt

#ubitx #digital #cat

I'm up and listening on PSK31 using fldigi, the hamlib setting communicates to ubitx very well. I'm listening for now until I figure out the proper etiquette. Thanks for the help everyone!!

#digital #ubitxv6 #psk31

Thanks Arv

#digital #ubitxv6 #psk31

http://www.w1hkj.com/beginners.html _._

#digital #ubitxv6 #psk31

I've used fldigi CAT with my v6, so definitely possible. Reed

#digital #ubitxv6 #psk31

Zvi, Thanks Do you know if fldigi can use CAT control (PTT and Freq control) and sound card through USB with ubitx directly?

#digital #ubitxv6 #psk31

You may try fldg. One downsize, it do not support omnirig, so you will not be able to communicate simultaneously with other SW like logbook. If you use LOG4OM, there is a workaround to use onmirig.

#digital #ubitxv6 #psk31

I've decided to try PSK31 and i'm looking for recommendations for best software and configuration. Does anyone have a recommendation as to which psk31 software is best to use and CAT control suggestio

#digital #ubitxv6 #psk31

That did the trick! Just made my first contact on FT8 with the uBITX! Thank you.

#bitx20 #cat #digital

Thanks for the link and thanks for the suggestions re the PA heat sinks/fans. I'm gonna dig through my stuff for small fan/s to suck the air out of my V6. Thanks again. Bob — KK5R

#bitx20 #cat #digital

I do not doubt that this will work, however, PTT works over the USB CAT link so that all that is really needed in the Easy Digi kit are the transformers to isolate the audio. I set up my WSJT-X using

#bitx20 #cat #digital

When I was trying to sort this out on my BITX40 I found using a breakout jack made short work of it. You might want to check out the wiki page I started https://groups.io/g/BITX20/wiki/6119 with what

#bitx20 #cat #digital