George, the issue may be computer failure to send TX over CAT. You'll likely have to double check USB/CAT configuration. Alternative: use Fldigi to work RTTY. There are lots of great configuration hel

#v5 #v6 #cat #rtty #psk31

I'll close it out. Although fldigi could not "see" the radio, flrig can read and write so I can control the radio from this computer. I set fldigi to use flrig as the front end and it works. I still h

#ubitx #digital #cat

Tnx Curt , I solved this within CEC 1.2 (Vic told me where to set) now its ok for me.

#calibration #cat

On similar lines I had written Arduino programs to control using Yaesu FT2000 protocol which is used by all modern Yaesu rigs. The library was announced in this forum in May 2020 and is available from

#arduino #cat #homebrew

Yes - you got it. 73, Dean KK4DAS

#cat #frequency #ubitx6-help

Stephen, Have you tried the "Fake It" setting under the Split section of the Radio tab? Here is the explanation from the WSJT-X manual: "Split Operation: Significant advantages result from using Split

#ft8 #ubitx6-help #cat #wsjt-x

That did the trick! Just made my first contact on FT8 with the uBITX! Thank you.

#bitx20 #cat #digital

I might try to use the existing Keyer plug to see if this would work, but the RigPi is not CAT control setup for uBitX so can't CAT connect naticely to RigPi will try and emulate the Yaesu 817 CAT con

#digital #v5 #ubitx-help #cat

OM Jack, The CAT is not that heavy. In fact the newer CAT commands are Two letter plus only required data and not like the earlier one sending 5 bytes for every command / data. I have separated the CA

#ubitx #bfo #cat

Thanks Evan, for time being your reply is just what I needed, so thank you very much. I already got ubitx and already have it working. My first impressions are good. But I already have a list of impro

#cat #ubitxv6

Hi Erwin Thanks for your reply. You are correct... I did change the monitor and that reduced the noise somewhat.. The real problem was that the PCB board that had the female USB-b socket mounted on it

#cat

Gary, Andy, + ....given droves of uBITX WSJTX users enjoy reliable CAT PTT for FT8 all over the world, it is clear uBITX PTT USB is reliable. Ditto for all the 24/7 uBITX WSPR mode obsessive fanatics

#v4 #cat #digital

On the ugly build uBITx I now have the latest CEC firmware installed, and a 4-line display (2004) I can receive and decode FT8 and WSPR via laptop running latest WSJT-x, connected via CAT. Setup : USB

#digital #v5 #ubitx-help #cat

Ha! A great analogy. Thank you!! Getting NanoNVA under my tree. A scope would force me to learn sooo much more... I'm going to focus on physically integrating my Atomic Pi SBC into my uBITX "case". An

#ubitx-help #cat

Hi Farhan - I have it configured as an FT-817. And it works - other than the periodic timeouts. Thanks, Dean KK4DAS

#cat #ubitx #v5

We all love our uBITX. Did you know the uBITX makes a wicked good digital mode beacon station using WSJT-X's cool beacon mode called WSPR? Well it does. We have a uBITX tied for 4th place in world-wid

#antennas #cat

Ah...good info. Thanks! I also added a BEC for some the 5v needs (plus a usb charge port), and a big dc-Dc buck converter for the 12v board. Now I can power it up with anything (almost) and the finals

#cat #ubitx #ubitx-help #arduino

Thanks Sasha for the summary write-up. Enjoy Your vacation! If the conditions are good and the radio gods are with us we might even get a QSO? :-) Regards. Jonas Den fre 24 maj 2019 kl 21:15 skrev Sas

#ubitx #cat #raduino #arduino

Hi, Good things come to procrastinators... This KV4QB site has a lot of interesting Ham related microprocessor projects. Including adding a TFT display to a uBitx. And a cool simulated analog meter us

#ft8 #cat #antennas #ubitx