Thanks AA9GG I had seen them too, the problem is that the first is only for the encoder and should be integrated and I am not able The second one has some problems in the compilation and uses so many

#arduino #bitx40help #bitx40 #nano

Thanks Don I had seen them too, the problem is that the first is only for the encoder and should be integrated and I am not able The second one has some problems in the compilation and uses so many fu

#arduino #bitx40help #bitx40 #nano

I had an encoder on my BitX40 but wound up going back to the 10-turn pot. I just made more sense since it's single band. Plus I was fighting trying to re-write the menu stuff to work with it.

#arduino #bitx40help #bitx40 #nano

Sergio: Here are two : http://www.nd6t.com/bitx/documentation/encoder 73, Don

#arduino #bitx40help #bitx40 #nano

Good evening I know the question might seem silly and pretentious! But since I don't know anything about programming, where can I find a sketch for the complete BITX40 already with the encoder? Thank

#arduino #bitx40help #bitx40 #nano

I attach a video of my creation and photos of the main components used

#arduino #bitx40help #radiuno #firmware

Thanks for the answers, but none of this! Even if a 10K linear potentiometer does not change, the frequency range is from 7.060 to 7.160 While if I use the same sketch on the original raduino the freq

#arduino #bitx40help #radiuno #firmware

Si5351 I2C interface to Arduino should be 3.2 volt pull-up with 4.7K resistors. This can be obtained from 3.2 regulated volts in the arduino. Puulling I2C up to 5 volts may damage the Si5351 ( I found

#arduino #bitx40help #radiuno #firmware

With the multiturn pot you need to changed the pot span to 300 to cover the whole band without jump tuning. Also, set the starting frequency to where ever you wish to start on power on. James

#arduino #bitx40help #radiuno #firmware

The OEM sketch for the BitX40 has a provision where it starts jumping up or down to the next tuning segment when you reach one end or the other of the tuning pot. In between the tuning is limited to a

#arduino #bitx40help #radiuno #firmware

Hi, I'm trying to reconstruct the raduino (DDS-VFO) for a BITX40. I used an arduino nano, a 16x2 display, a 10K multiturn potentiometer and a Si5351a card. All provisionally mounted on a breadboard. T

#arduino #bitx40help #radiuno #firmware

HI all I'm facing a problem with my ubitx V5 i can't change the frequency or going trow the Sub Menu program i changed the KNOBE encoder the same problems the frequency is frozen and the menu too so h

#arduino

Ah...good info. Thanks! I also added a BEC for some the 5v needs (plus a usb charge port), and a big dc-Dc buck converter for the 12v board. Now I can power it up with anything (almost) and the finals

#cat #ubitx #ubitx-help #arduino

So now I'm stuck on getting uBITX cat control working on the AtomicPi in Lubunto. The audio works great, I get decodes!! So good there. I have tried every option on the Device dropdown list. No love.

#cat #ubitx #ubitx-help #arduino

Don, I 'cut the red wire' because I had already removed the Raduino 5v regulator and modified my v3 boards audio to have a 5v supply (and the Raduino, USB hub etc) separately supplied from a small rad

#cat #ubitx #ubitx-help #arduino

okay, so after a day (almost) of back and fourth, it was clear to me that only COM7 was loved by the uBITX cat control. I finally threw in the towel (I didn't even know I had a towel!) and deep in the

#cat #ubitx #ubitx-help #arduino

Doug and Nigel, yes so I'm trying to copy at least Nigel, and many others (which is good news). As suggested, Win10 reassigned the cat com port from COM7 to COM13 when I put the cat usb cable into the

#cat #ubitx #ubitx-help #arduino

I think I was one of the first to add an 'all-in-one' USB solution inside a uBitx with a small 4 port hub? I also did the 'cut the red wire' at that time. I had posted it here... https://groups.io/g/B

#cat #ubitx #ubitx-help #arduino

Don, Something doesn't make sense. I hate it when people say it works for me so it must work for you, but I am going to be that guy. There should be no problem using a USB sound card and a CAT control

#cat #ubitx #ubitx-help #arduino

hello! When i got my sound card dongle and cat control working each in their own USB port on my Win10 laptop, I almost fainted from uBITX joy. It is reliable and works well. So time to move on. Hahah.

#cat #ubitx #ubitx-help #arduino