Date   
Re: Second batch of uBITX shipping? #ubitx

K9WIS
 

I ordered on Dec 14 and have not heard from them since...I did hear rumor shortly after I ordered that it wouldnt ship until the end of January..That day is fast approaching and still no word. Maybe we need to bring this project onto US soil..
Brian K9WIS

---- mikael.madsen@... wrote:

Someone posted that order date 14th december had been shipped but that was some days ago.

Anyone with a later order date later than 14th been informed of shiping yet?

Re: uBitX - Replacement microphone

 

Sajid : 

I am using a Koss CS-100 Computer headset on my BITX40 with excellent results. These cost less than $US20. 
I have tried a couple of other inexpensive Computer Headsets and have found that with some the microphone is 
not sensitive enough for use with the BITX (i.e. output is very low). 

 I have also used a more expensive Yahama CM-500 that works very well.
The nice thing about computer headsets is that the non-USB models normally use 3.5mm stereo plugs for both Headphone and 
mic connections, making it easy to get jacks and to drill appropriate sized holes in your enclosure.

Cheers

Michael VE3WMB 

P.S. For PTT I am using large momentary switch mounted in a plastic pill box with a 3.5mm stereo jack on the bottom. This allows me to 
use a normal 3.5mm audio cable to connect it to the rig. 

Re: Modular BiTX40

Mike Doty
 

Hi Manoel,
My group has had a lot of fun working on this project.  With winter upon us (lots of snow), and living up in the mountains in the northwest U.S., getting together for classes is a challenge.  We have had two classes to date and the group has completed assembling and testing the audio amps board, the 3 bidirectional amps,  the low pass filter, and installed all of the SIP sockets on the motherboard.  Our next class is scheduled for 17 Feb and the plan for this session is to complete and test the crystal filter, the mixer, the product detector, and the VFO.  We'll save the PA module for last along with building the external VFO (Si5351).  I did find that on the analog VFO it was almost impossible to eliminate the drifting so I decided not to install those components since we will be using an external VFO anyway.

The only fault I found with any of the boards was that you didn't include pads to connect M1/M2 from the relay on the PA module to the audio amp module.  I worked around this by soldering two wires with a header to the relay contact pads on the PA module.  The header plugs in to pins on the motherboard with traces running to the audio amp module.

Again, it was terrific of you to share your work on Hackaday and the experience that my guys are getting from building this transceiver is invaluable.  If you will email me direct I would be pleased to mail you one of the motherboards that I designed for the project as my way of saying thank you.

--73-- Mike  --  W0MNE

Re: IRF510 amplifier failures

Jerry Gaffke
 

The RD15HVF1's should be operated at not much more than 12v.
At 12v, the IRF510's would survive just fine with no antenna connected.
That's an infinite VSWR.

So not obvious that this is a solution to blown FET's.
Though I do think the the Ids curves go up more slowly as Vgs increases on the RD15HF1's,
which makes RV2,RV3 not so touchy.
And the RD15HF1's might be easier to drive at 30mhz.
If you do swap them in, let us know how much power you get at 30mhz.

Jerry, KE7ER


On Fri, Jan 26, 2018 at 03:54 am, KD8CGH wrote:
Wouldn't it be better to change to a RD15HVF1 for high VSWR

Re: Slack Client group

David Arthur
 

See my signature below for a link to join the Discord. For all intents and purposes, it's the same as Slack. 

3-5 people are usually active, 51 people have logged in at one point so far.

Cheers!
--
David K4DBZ
Unofficial bitx chatroom: https://discord.gg/CrHvWFc

Re: remote display was Apache Case on Sale

Rod Davis
 

Jack and All,

attached 2 pix of remote display. Note that I used DuPont wires that came as a flat-group, not the helter-skelter loose wires.
Probably helps reduce noise to some degree.

The ubitx is in an old Heathkit Frequency counter cabinet. When fully assembled, the cabinet looks good, and has
plenty of room for add-ons, and has good cooling louvers.

I will install a fan just behind the finals. The fan will be pulling air away from the finals, not blowing onto them.

Downside of using this case: the 12 inch Nano USB extension cable will not reach the back panel; had to bring
it out through the front.

Rod KM6SN



On 01/26/2018 08:38 AM, Jack Purdum via Groups.Io wrote:
That's good news! I'm thinking of using ribbon cable and grounding every other wire.

Jack, W8TEE



From: Rod Self <km6sn@...>
To: BITX20@groups.io
Sent: Friday, January 26, 2018 11:35 AM
Subject: Re: [BITX20] remote display was Apache Case on Sale

Jack,
I used 6 inch Dupont wires with no shield-no apparent problems.
Rod KM6SN


On 01/26/2018 06:43 AM, Jack Purdum via Groups.Io wrote:
I think there are a number of people who have moved the display away from the main board to give them some flexibility in terms of display placement. Evidently, some shielding is needed, but I think I recall someone simply wrapping the cable in foil mitigated the problem. I'd like to hear from anyone who has moved the display and what their experience is.

Jack, W8TEE



From: KE0GYC <dragonfanatic90@...>
To: BITX20@groups.io
Sent: Friday, January 26, 2018 9:24 AM
Subject: Re: [BITX20] Apache Case on Sale

I love the idea of a "portable field radio" with all the controls on the top in a watertight case like this.  I'm thinking of modeling it after a bitX40 build I saw here, and this case looks like the perfect size!

Is there any reason I couldn't do that with the uBitx?  It looks like the LCD plugs directly into the board, but would it give me noise issues if I used a short length of ribbon cable to move the LCD to face upwards?



Virus-free. www.avast.com




Re: BITX QSO Afternoon/Night, Sunday, January 28, 3PM/7PM Local Time, 7277 kHz in North America, 7177 kHz elsewhere

Tom VE3THR
 

good call Ed. The GM (General Motors Employee/retirees) net operates on 7.277.5 - should NOT be a problem but can be used to check propagation during the week.                    GM HF Net Mon thru Sat 1:00pm (HF 7,277.5 KHz). 
I think the mod to RLS 2 will help with the heterodyne we hear AM broadcasters in our 40M ham band in North America. I don't have the new uBITX built yet but I'm hoping it's not a problem too. Using an external DSP and/or notch filter does help a lot.

Re: IRF510 amplifier failures

James Lawrie
 

On same site I found these, made for 30 MHz RD16HHF1. Sooo I bought 10 of them, plan to try in Bix40 first. Data sheet even shows a reference amp design, and they are 12 volt like the other one. If it works I’ll let everyone know.

James Lawrie

On Jan 26, 2018, at 11:32, Jerry Gaffke via Groups.Io <jgaffke@...> wrote:

The RD15HVF1's should be operated at not much more than 12v.
At 12v, the IRF510's would survive just fine with no antenna connected.
That's an infinite VSWR.

So not obvious that this is a solution to blown FET's.
Though I do think the the Ids curves go up more slowly as Vgs increases on the RD15HF1's,
which makes RV2,RV3 not so touchy.
And the RD15HF1's might be easier to drive at 30mhz.
If you do swap them in, let us know how much power you get at 30mhz.

Jerry, KE7ER

On Fri, Jan 26, 2018 at 03:54 am, KD8CGH wrote:
Wouldn't it be better to change to a RD15HVF1 for high VSWR

Re: uBitX - Replacement microphone

Sajid Rahum
 

Thanjk you Michael
Let me check your suggestion.

Re: batch shipping

 

I sent a mail to hfsignals they said the next round is in about 2 weeks. I also ordered on the 23rd.
--
David

 N8DAH
Kit-Projects.com

Re: IRF510 amplifier failures

Thomas Sharka
 

On Friday, January 26, 2018 1:01 PM, James Lawrie <lawriejk@...> wrote:


On same site I found these, made for 30 MHz RD16HHF1. Sooo I bought 10 of them, plan to try in Bix40 first. Data sheet even shows a reference amp design, and they are 12 volt like the other one. If it works I’ll let everyone know.

James Lawrie

On Jan 26, 2018, at 11:32, Jerry Gaffke via Groups.Io <jgaffke@...> wrote:

The RD15HVF1's should be operated at not much more than 12v.
At 12v, the IRF510's would survive just fine with no antenna connected.
That's an infinite VSWR.

So not obvious that this is a solution to blown FET's.
Though I do think the the Ids curves go up more slowly as Vgs increases on the RD15HF1's,
which makes RV2,RV3 not so touchy.
And the RD15HF1's might be easier to drive at 30mhz.
If you do swap them in, let us know how much power you get at 30mhz.

Jerry, KE7ER

On Fri, Jan 26, 2018 at 03:54 am, KD8CGH wrote:
Wouldn't it be better to change to a RD15HVF1 for high VSWR


Re: batch shipping

Chris Clarke G3SQU
 

Is anyone up for maintaining a database of Bitx by serial no. to include purchaser, ordering, shipping and delivery dates, and info about subsequent issues and modifications?


For info, mine was ordered on 16-Dec (for shipping to UK via Indian P.O.), acknowledged by email from HFSignals on 31-Dec, and a couple of days ago (following my enquiry to HFSignals) I was informed it would ship in 2-3 days. No advice from PayPal as yet.


Chris

G3SQU


From: BITX20@groups.io <BITX20@groups.io> on behalf of N8DAH <Dherron@...>
Sent: 26 January 2018 18:13:24
To: BITX20@groups.io
Subject: Re: [BITX20] batch shipping
 
I sent a mail to hfsignals they said the next round is in about 2 weeks. I also ordered on the 23rd.
--
David

 N8DAH
Kit-Projects.com

Re: Something has been blown

César EA3IAV
 

It is very frustrating. I don’t have any watt showing up in my power meter even in the 2w scale
how do I know I blew the fets again? 
When ptt i get 0,5amp and adjustin It is too sensitive. Even one time it got crazy with a very loud beep coming through the speaker an i had to turn it off
when i whistle no extra power is drained

Re: Apache Case on Sale

John McFadden
 

I bought two 1800s, they would not fit my ubitx pcb at the bottom of the case by a fraction of an inch because of the orientation of the raduino and heat sinks on the short axis of the card, they must point to the sides. Leaving the long axis of the card to fit front to back in the case. 

Instead, I selected the Seahorse SE300, more expensive, but also has screw bosses molded into both the case and lid which means easily hanging the PCB from stand offs instead of puncturing the case. 

John

On Jan 26, 2018 10:48 AM, "John P" <j.m.price@...> wrote:
Here's a link! This if the January flyer, so it doesn't show the sale price.
--
John - WA2FZW

Caveat Emptor!

John P
 

I just received 3 of the MCUFriend 3.5" TFT displays purchased from "accecity2006" on eBay. One of the 3 worked correctly; one was cracked and another one was not displaying text correctly.
--
John - WA2FZW

Re: IRF510 amplifier failures

Arv Evans
 

Interesting comments thus far regarding IRF510 failures. 
  • Power supply current limiting (2.5 to 3A) seems to work.

  • Bias voltage shutdown on high current (3A) seems to work.

  • Driver impedance to IRF510 gate should be quite "stiff".  Use a 50 ohm pad.

  • Use small resistance (4.7 ohms) in series with each IRF510 gate lead.

  • Keep IRF510 leads short.

  • Impedance presented to the IRF510 drain should be 12.5 ohms.
    RF output transformer should be 1:2 windings for 1:4 impedance transition.
    Binocular core may work better...?

  • Avoid the problem by using some other MOSFET.

  • Use plastic fuses at 3A for self-healing action.

  • Fuse rig power at 2 to 3A to avoid IRF510 failures.
Some of the on-line information also mentioned low level background noise being
generated by MOSFET RF PA stages that remain powered during receive mode. 
Possible solution here might be to add a MOSFET switch in the DC power lead
going to the IRF510s so this power could be shut off during receive.

All good info.  Now how to keep within the original BITX objective of making rigs
that can be afforded by those with limited spare cash and still make them reliable
and inexpensive.  This solution(s) has potential for modification of existing
transceivers, and for future redesign of the similar units.  It also has application
for designing and adding homebuilt RF amplifiers for your BITX rig.

Arv  K7HKL
_._


On Fri, Jan 26, 2018 at 10:32 AM, Jerry Gaffke via Groups.Io <jgaffke@...> wrote:
The RD15HVF1's should be operated at not much more than 12v.
At 12v, the IRF510's would survive just fine with no antenna connected.
That's an infinite VSWR.

So not obvious that this is a solution to blown FET's.
Though I do think the the Ids curves go up more slowly as Vgs increases on the RD15HF1's,
which makes RV2,RV3 not so touchy.
And the RD15HF1's might be easier to drive at 30mhz.
If you do swap them in, let us know how much power you get at 30mhz.

Jerry, KE7ER

On Fri, Jan 26, 2018 at 03:54 am, KD8CGH wrote:
Wouldn't it be better to change to a RD15HVF1 for high VSWR


Re: Caveat Emptor!

Ken
 

Contact the seller and have them replaced.

Ken VA3ABN

On Fri, Jan 26, 2018 at 2:47 PM, John P <j.m.price@...> wrote:
I just received 3 of the MCUFriend 3.5" TFT displays purchased from "accecity2006" on eBay. One of the 3 worked correctly; one was cracked and another one was not displaying text correctly.
--
John - WA2FZW


Re: Lost in Customs?

DJ2AG
 

Last tracking information for mine was „2017-12-19 00:19 Germany, FRANKFURT/FLUGHAFEN, Receive item at office of exchange (Inb), Air“

On 29th I got a letter from local customs office (Zollamt) that a parcel ist waiting for me. Paid VAT and fetched it. But this last step doesn’t show up in tracking. Maybe your Zollamt is a bit slower than mine, and 
you just have to wait. Gut Ding will Weile haben.

Re: Caveat Emptor!

Dennis Zabawa
 

It is quite possible that the vendor is selling slightly defective culls from the production line.  Reputable manufacturers clearly mark such items to prevent them from being sold as fully working items.  Others sell them off with no warning, while others destroy them.  Luck of the draw

Re: Caveat Emptor!

Arv Evans
 

John

My experience with high density displays is not any better.  I have 5 of the small 0.92 inch
displays but have not been able to get any of them to work.  These are TWI or I2C interface
and my Arduino does not recognize any.  I have tried the example code, the TWI address search
code, and my own TWI interface code, all to no avail.    At present I seem to be limited to using
the old standard 1602 LCDs, 4-line 16 char LCDs, and using the ttl/USB interface to show Arduino
outputs on my PC. 

Given my non-success experience with the 0.92 inch screens I have been hesitant to invest in
larger wire-bus connected displays.  Your experience seems to say it is good that I have not
purchased larger displays.

I wonder who, if anybody, has had good luck with these type screens?  The wire.h library
seems straight-forward and easy to use, but it just does not work with displays I have tried.
I even used the example code without making any modifications and it still doesn't work.

Arv
_._


On Fri, Jan 26, 2018 at 12:47 PM, John P <j.m.price@...> wrote:
I just received 3 of the MCUFriend 3.5" TFT displays purchased from "accecity2006" on eBay. One of the 3 worked correctly; one was cracked and another one was not displaying text correctly.
--
John - WA2FZW