Date   
Re: manhattan style pads

Hans Summers <Hans.Summers@...>
 

 
> I agree with Hans -- I have really seen no difference between
> construction on a ground plane when using pads and building
> without them, other than building without is faster.     
> There is rarely a need to go as high as 10M with the
> resistors if you don't have them around.   Something
> much smaller values will work just as well.
 
Yes, true - I found that Rapid Electronics sell a very useful resistor variety pack containing 1000 resistors in 63 values from 4.7ohms to 10M. The number of each varies from 5 to 30 depending how common they think they are. E.g. they have 30x 10K, 100K etc, and only 5x 830K. Price is £9.75. I just *KNOW* I probably won't want the 10M and they've put 20 of them in. Thought I'd start at the top and work my way down through 6M8, etc.
 
72/3 de Hans G0UPL
http://www.HansSummers.com

Block Diagram

Charles Darley
 

Hi

I have just posted a block diagram of the BITX - I hope I have
correctly identified all the section of the main schematic diagram.

Let me know of any errors.

This will be used as part of a teaching aid to Amateur Radio Students
in UK.


Charles

A tale of two tap washers

Hans Summers <Hans.Summers@...>
 

...in which G0UPL travels to his local hardware store to further investigate
the nature of the infamous tap washers, and in particular the differences
between ordinary and "delta" washers. Samples were successfully returned to
my office and analysed in the photocopier next to a ruler then via the
scanner ;-)

Attached is a picture. For the benefit of those who don't get emails but
read this on the Yahoo group website, I've put it in the G0UPL photos folder
too. Note: Ruler measurements to the left of the 6 inch mark are in 16'ths,
to the right are in 10'ths.

Both are know as 1/2 inch tap washers but both measure more than 1/2 inch
(12.7mm). As close as I can measure with my ruler:

"normal" "Delta"

Outside diameter: 23/32 (18mm) 19/32 (15mm)
Inside hole diam: 5/32 (4mm) 3/16 (5mm)
Thickness: 5/32 (4mm) 3/16 (5mm)
Price: £0.45 per 3 £0.45 per 2

72/3 de Hans G0UPL
http://www.HansSummers.com

Re: BITX20 component list

ik1zyw <pcravero@...>
 

--- In BITX20@..., "ik1zyw" <pcravero@a...> wrote:

It's me again.

Has anyone attempted to list all BITX20 components? I haven't found
any link on Ashan's page. Here is my attempt at listing all
components, except for the IRF510 PA (had no time).
I have uploaded in the Files section a TXT file with a component list
for BITX20. It DOES include driver/PA section but it DOES NOT include
inductors. The list is meant to be a list you give to the shop
attendant and then return home with everything you need to build a BITX20.

Tap washers can be purchased at a hardware store, which usually
doesn't sell electronic components. Coils wire can be salvaged from
old transformers.

Please someone cross-check my work!

73,
Paolo IK1ZYW

Off topic - i am blocked out

Ashhar Farhan <farhan@...>
 

for the last 48 hours, groups.yahoo.com has been blocked out by the two
major bandwidth providers to india. most of my internet accounts belong to
isps that in turn take their bandwidth from either of these two (i have
several).

this has been done as the indian govt. asked the isps to block certain a
fanatic group (read 'hate') from being accessed from india. some of us
are fighting this with the govt. and i hope that the access will be
restored soon.

until such a time, i cannot see the pictures that are being uploaded
although access the emails (the emails are to and from my server located
in boston). i cannot wait to see all the lovely efforts being made by
everybody and it feels like being left out of the party.

though a number of users have suggested using proxies to gain access to
the site, i want to regain my right to free exchange of ideas and
information as much as i believe the fringe hate group should. the issue
has become significant to a number of us in india.

- farhan

Re: Off topic - i am blocked out

Hans Summers <Hans.Summers@...>
 

Farhan

Sorry to hear of your problems. I'm sure you are right to fight for the free
exchange of information.

One possible solution is to use an anonymisation service such as
http://www.anonymization.net . In this case the URL to the BITX20 group
would become
http://www.anonymization.net/http://groups.yahoo.com/group/BITX20/ .

I work for a US company. One might expect freedom of information to be
assured. But they insist nevertheless on blocking any website which meets
some criteria of being pornographic, related to betting and gambling, or any
terrorist activity. I don't know if they thought that perhaps we would sit
here in the office in full view of our colleages watching porno movies or
something. Anyway be careful I'm getting on my soapbox here...

To cut a long story short, I had a big battle and I lost, they still refuse
to change it. The battle arrived when I tried to look at the website of
Thomas OZ2CPU, whose excellent web page http://www.webx.dk/ I have visited
many times in the past. Only to find that it was blocked, with a message
something like "if you feel this web page has been wrongly blocked, please
contact the IT helpdesk". You can contact them as much as you like, and if
they don't feel it is related to your business requirement they won't
unblock it, even if it IS wrongly blocked. A colleague wanted to buy
something from a camping store. Couldn't access it. So had no option but to
take a long lunchbreak of 2 hours, on company time, to visit the store. Even
if it's non-business, it can assist business by making the employee's life
easier.

All of which led me to write my own internet browser application, which
enclosed an Internet Explorer component. On coming across the hated IT
helpdesk message, it redirects its enquiry to anonymization.net which
(nearly always) gets the page Ok. This is all done in an invisible way, the
actual real address at anonymization.net is hidden from the user. So I was
able to give the application to my friends in the company to assist them in
streamlining their non-business related activities, in the knowledge that if
the information finds its way back to the IT dept, at least it won't be
instantly evident how it works, though I don't doubt that they would be able
to trace it eventually, having access to everything.

Sorry to have got on my soapbox even though I tried to stay off it - this
issue touches a raw nerve. Good luck with battle which is much more serious
than my little problem here.

73 Hans G0UPL

-----Original Message-----
From: Ashhar Farhan [mailto:farhan@...]
Sent: 28 June 2004 12:59
To: BITX20@...
Subject: [BITX20] Off topic - i am blocked out



for the last 48 hours, groups.yahoo.com has been blocked out by the two
major bandwidth providers to india. most of my internet accounts belong to
isps that in turn take their bandwidth from either of these two (i have
several).

this has been done as the indian govt. asked the isps to block certain a
fanatic group (read 'hate') from being accessed from india. some of us are
fighting this with the govt. and i hope that the access will be restored
soon.

until such a time, i cannot see the pictures that are being uploaded
although access the emails (the emails are to and from my server located in
boston). i cannot wait to see all the lovely efforts being made by everybody
and it feels like being left out of the party.

though a number of users have suggested using proxies to gain access to the
site, i want to regain my right to free exchange of ideas and information as
much as i believe the fringe hate group should. the issue has become
significant to a number of us in india.

- farhan






Yahoo! Groups Links

TV Balun

g4dfv2004 <duncan.walters@...>
 

Hello, I have uploaded a photo of a two-hole "binocular" ferrite
core (see G4DFV album). Ashtar, please can you tell me if this is
anything like the TV balun that you have used?
My core measures 13mm x 7mm x 6mm, the holes are 3mm diameter and
the centres are spaced 6mm.

Duncan G4DFV

Re: Off topic - i am blocked out

Mark Jones <Mark@...>
 

Farhan
 
Fine on all of this, I have friends in your country who have reported the same before now.
 
Hope you get access soon,
 
Mark G0MGX

-----Original Message-----
From: Ashhar Farhan [mailto:farhan@...]
Sent: 28 June 2004 12:59
To: BITX20@...
Subject: [BITX20] Off topic - i am blocked out


for the last 48 hours, groups.yahoo.com has been blocked out by the two
major bandwidth providers to india. most of my internet accounts belong to
isps that in turn take their bandwidth from either of these two (i have
several).

this has been done as the indian govt. asked the isps to block certain a
fanatic group (read 'hate') from being accessed from india. some of us
are fighting this with the govt. and i hope that the access will be
restored soon.

until such a time, i cannot see the pictures that are being uploaded
although access the emails (the emails are to and from my server located
in boston). i cannot wait to see all the lovely efforts being made by
everybody and it feels like being left out of the party.

though a number of users have suggested using proxies to gain access to
the site, i want to regain my right to free exchange of ideas and
information as much as i believe the fringe hate group should. the issue
has become significant to a number of us in india.

- farhan



Chip pad

Charles Darley
 

Hi

I was wondering how to make a pad for the chip then thought use a
piece of PCB with a cut through the copper in the centre and then
additional cross cuts of the copper to make the lands for the holder.

By bending out the legs of the holder they can be soldered to the pad.

Chip Pad Photo added to my album.

Charles G4VSZ

non-ferrite balun cores

Arvid Evans <arvevans@...>
 

BITXers

Since the tap washers, faucet washers here in the US, are mylon or
similar plastic type material, it would seem that they do not
contribute much to the functionality, other that to hold the wire
coils in a circular shape. Also, since there is no magnetic field
contribution by the nylon or plastic dore former it would seem that
one could cut a small slot in the material to facilitate winding the
coil without having to thread each turn through the center hole.

After the coil was wound one could use hot-melt glue (or anything
sticky that hardens well) to close the slot and to mount the coil to
the chassis material.

Has anybody tried this yet?

Thanks,

Arv-K7HKL
_._

Re: Chip pad

John Fisher <k5jhf@...>
 

Very nice pads, applicable to many projects. I use an 8 pin Motorola microcontroller in my Morse Code training device, and this will be great for those projects too. Info on the MCD is on my webpage below.

 Regards,
 John
 
=============================================
email:      k5jhf@...
photos:   http://photos.yahoo.com/k5jhf@...
files:       http://briefcase.yahoo.com/k5jhf@...
webpage: http://www.geocities.com/k5jhf@...
callsign:    K5JHF
=============================================

-----Original Message-----
From: Charles [mailto:charles@...]
Sent: Monday, June 28, 2004 4:20 PM
To: BITX20@...
Subject: [BITX20] Chip pad

Hi

I was wondering how to make a pad for the chip then thought use a
piece of PCB with a cut through the copper in the centre and then
additional cross cuts of the copper to make the lands for the holder.

By bending out the legs of the holder they can be soldered to the pad.

Chip Pad Photo added to my album.

Charles G4VSZ




Re: Chip pad

vk3bfa <ablight@...>
 

Hi Charles,
what you describe has been used in VK for a while now, described (and
used) by Drew Diamond VK3XU - he is a master of this style of
homebrewing and has published many articles over the years (and 2
books) - some construction articles are available in .PDF format from
the website
http://www.wia.org.au/links/ go to AR mag page and have a look around.
Well worth the effort for inspiration!
73 de VK3BFA Andrew

-- In BITX20@..., "Charles" <charles@d...> wrote:
Hi

I was wondering how to make a pad for the chip then thought use a
piece of PCB with a cut through the copper in the centre and then
additional cross cuts of the copper to make the lands for the
holder.

By bending out the legs of the holder they can be soldered to the
pad.

Chip Pad Photo added to my album.

Charles G4VSZ

Re: A tale of two tap washers

Sam Caldwell <samc@...>
 

Hans Summers wrote :

...in which G0UPL travels to his local hardware store to further investigate
the nature of the infamous tap washers, and in particular the differences
between ordinary and "delta" washers.
Both are know as 1/2 inch tap washers but both measure more than 1/2 inch
(12.7mm). As close as I can measure with my ruler:
As I understand it, the " half -inch' refers to the bore of the water
pipe with which they are associated - and includes three-quarter and
one-inch as part of the series.

A typical "half-inch" tap washer in the past would measure perhaps
three-quarters of an inch dia., but in more recent times the
proliferation of fancy bathroom ware has given rise to a variety of
custom taps (faucets) with their own washers.

My own houshold taps ( I'm told ) have ceramic washers which ( I'm
told ) never wear out and ( I know ) are drip-free.

Regards, Sam C.
ZL1TOI

Digital dial for BITX20 using PIC

vk3bfa <ablight@...>
 

Hi fellow builders,
posting this link for information
http://www.wia.org.au/armag/2002/AR_Sept02_Digital_Freq_Display.pdf
- its a digital frequency readout using a PIC micro with user
definable IF offset - might be of use to the group, and I readily
admit its outside Ashan's original inexpensive transceiver concept -
it would probably cost more to build than the BITx20 itself!
Still, I think its an elegant solution, so let me know what you think.
Its .PDF, approx 162K in size
73 de VK3BFA Andrew

Re: A tale of two tap washers...the saga goes on, an on

Arvid Evans <arvevans@...>
 

Sam & other BITXers

Your measurements explain my results then. Instead of tap/faucet
washers I used 1/4 inch slices cut from "1/2 inch" PVC pipe (the
schedule-40 or medium-thick-wall type). These measure about 13/16" OD
and 5/8" ID.
In my BITX20 I followed Farhan's instructions regarding the nunber of
turns and my coils came out nearly perfect for inductance value.

I just wound a second set of coils using the PVC material and
facilitated the winding process by cutting a slot in the plastic
former. This means I did not have to thread the wire through the core
150 times. These new coils check out on the dip meter as also being
on-the-money for inductance.

It is interesting that these "air-core" toroids exhibit some of the
same characteristics as ferrite cored units. My dip meter does not
get a strong coupling to the coil itself unless I add a coupling loop
through the core. I thought that phenomena was due to ferrite
channeling the magnetic field, but maybe the shape of the coil has
more influence than I thought.

Arv
_._
--- In BITX20@..., Sam Caldwell <samc@x> wrote:
Hans Summers wrote :

...in which G0UPL travels to his local hardware store to further
investigate
the nature of the infamous tap washers, and in particular the
differences
between ordinary and "delta" washers.
Both are know as 1/2 inch tap washers but both measure more than
1/2 inch
(12.7mm). As close as I can measure with my ruler:
As I understand it, the " half -inch' refers to the bore of the water
pipe with which they are associated - and includes three-quarter and
one-inch as part of the series.

A typical "half-inch" tap washer in the past would measure perhaps
three-quarters of an inch dia., but in more recent times the
proliferation of fancy bathroom ware has given rise to a variety of
custom taps (faucets) with their own washers.

My own houshold taps ( I'm told ) have ceramic washers which ( I'm
told ) never wear out and ( I know ) are drip-free.

Regards, Sam C.
ZL1TOI

Re: Chip pad

Hans Summers <Hans.Summers@...>
 

I was wondering how to make a pad for the chip then thought
use a piece of PCB with a cut through the copper in the centre
and then additional cross cuts of the copper to make the lands
for the holder.
That's what I do too, when I need to. I use firm pressure on one of those
cheap orange plastic "craft" knives. You can produce a nice thin cut with
this method. The LM386 in the BITX20 I just mounted "ugly" though, with no
pads. I tend to use the knife method if I need to use surface mount IC's.

The pinnacle of the art came when I found I had to connect a 24-pin Analogue
to Digital converter chip, in a TSSOP package. Pin spacing was a mere
0.65mm. In other words, 4 times denser than your BITX20 LM386. To do this I
cut 2 columns of 6 pads on either side of the IC (24 pads total). I glued
the IC to the board. The even-numbered pins (2, 4, 6 etc) were bent upwards
away from the board. Odd-numbered pins (1, 3, 5 etc) were soldered direct
onto the pads. The even-numbered pins were then connected to the outer
columns of pads using the hair-thin individual strands of copper from
ordinary lighting cable. You can find a picture of the result about 2/3 down
on the left hand side of this page
http://www.hanssummers.com/electronics/equipment/spectrumanalyser2/index.htm


People who work with SMD talk of special soldering irons & bits, special
solder, magnifying glass, flux, special lights etc etc. I used none of this.
Just my ordinary 18W Antex CS iron with 1mm bit and ordinary 22swg solder.
Just goes to show that the patient homebrewer can accomplish a lot even
without specialist equipment.

72/3 de Hans G0UPL

Re: Chip pad

g4dfv2004 <duncan.walters@...>
 

An easier method to make a pad for non-SMD IC's is to use 0.1"
Veroboard instead of plain copper laminate.
Then only one saw/knife cut is required.
KISS?

Duncan G4DFV

Re: Digital dial for BITX20 using PIC

Hans Summers <Hans.Summers@...>
 

A very nice readout. But for anyone wanting something *really* simple, have
a look at my 2-chip binary readout counter
http://www.hanssummers.com/radio/sfreq/index.htm . Also see my BITX20 in the
G0UPL photos folder to see it installed in my front panel.

My latest version is even simpler by using a 74HC390 instead of the
74HC4040, eliminating 5 diodes and 2 resistors from the circuit. The output
is also easier to read: 2 columns of LED's indicating 80, 40, 20, 10 and 8,
4, 2, 1KHz. This is easier to add up than the binary 64, 32, 16, 8, 4, 2, 1,
0.5Khz of my earlier versions. The reading is 0 - 99KHz, my dial is marked
14.0, 14.1, 14.2, 14.3 and this is added to the counter reading to get the
reception frequency. The 1KHz LED flickers such that it's brightness can be
used to estimate the frequency inside the 1KHz resolution.

Would anyone be interested if I were to offer a complete kit of parts (for
ugly construction, i.e. no PCB), suitable for connection to the BITX20 VFO
as in mine? The pack would include: 74HC4060, 74HC390, 5V voltage regulator
+ filter, 8x 3mm high-brightness red LED's, single transistor VFO buffer
amplifier, all diodes resistors and capacitors. Cost £3.37 + postage (as
usual, parts cost only, no profits for poor G0UPL). If enough people were
interested I could do this.

72/3 de Hans G0UPL

-----Original Message-----
From: vk3bfa [mailto:ablight@...]
Sent: 29 June 2004 01:56
To: BITX20@...
Subject: [BITX20] Digital dial for BITX20 using PIC


Hi fellow builders,
posting this link for information
http://www.wia.org.au/armag/2002/AR_Sept02_Digital_Freq_Display.pdf
- its a digital frequency readout using a PIC micro with user definable IF
offset - might be of use to the group, and I readily admit its outside
Ashan's original inexpensive transceiver concept - it would probably cost
more to build than the BITx20 itself! Still, I think its an elegant
solution, so let me know what you think. Its .PDF, approx 162K in size 73 de
VK3BFA Andrew

Re: Block Diagram

Mark <Mark@...>
 

Charles,

Where did you post it?

--- In BITX20@..., "Charles" <charles@d...> wrote:
Hi

I have just posted a block diagram of the BITX - I hope I have
correctly identified all the section of the main schematic diagram.

Let me know of any errors.

This will be used as part of a teaching aid to Amateur Radio
Students
in UK.


Charles

Re: Chip pad

Jim Strohm <jstrohm@...>
 

On Jun 29, 2004, at 3:31 AM, g4dfv2004 wrote:

An easier method to make a pad for non-SMD IC's is to use 0.1"
Veroboard instead of plain copper laminate.
Then only one saw/knife cut is required.
KISS?
And an even easier -- yet vastly more expensive -- method is to use one of the etched adapter boards that brings out the pins from a surface-mount chip to 0.1-in spacing pads. SMD chips can be soldered to these with little difficulty and a small iron as Hans noted. Nowadays I use a lighted magnifier -- even on DIP stuff -- because it's a lot easier on me.

And I have a cute little Intel Play USB microscope that has a 10X setting for the more challenging SMD stuff.

Jim N6OTQ