Date   
Power OUT .. #bitx20

HB9FIH
 

abt all - I am a bit in doubt abt uBITX if I read all the topics about the different issues and problems - with calibration , Filters etc.

BUT I have started - with ordering and collecting all the parts. (most are received in HB9)

Assembling will do in December when I will be in QTH EA8 (now in SV8 on my ship).

I will first build the Original uBITX and tune them up. After I change the Firmware to K5CEC .

Then assemble the AGC (QRP-Kits) and the CW-Filter (Sotabeams).

After assembling the 2.8" Nextion display.

Now, some write about Power out too less ... for me is this in reverse....I would be able to decrease the power out , down to abt 100mW

I checked the scematics an found the R85 100 Ohms. - Is this ok for decreasing PWR to assembe a 100 Ohm Variable resistor which pulls the Basis to GND.?

TNX for confirmation Erich

Ubitx 5.1 software compile errors

paul wegwert
 

Hi all,

I have just spent the better part of four hours trying to download ubitx software version 5.1 from the ubitx.net, github, ect. The only one I was able to download and compile was ver x0.0020? (I think). Anyway I would like to have a spare Nano with the original 5.1 software but I get errors such as: "'checkCat' was not declared in this scope" and "'si5351bx_setfreq' was not declared in this scope'. 
See attached.
I have tried several times and I am stuck. Any ideas?

Thanks,

Paul
kd9jyv

Re: Edge meter

Mike WA0YCN
 

Thanks guys.  I am going to try the zero adjustment with the meter that came with the kit. But I also ordered one of the Workman meters.  :)  They have the leads on the top side, so we’ll see if it will work with the Nextion case. 

Re: Wattmeter kit on eBay

Zachary Ledbetter
 

I have used one of these for over 2 years!  Just be very careful regarding the polarity when connecting the display as it not protected.  I installed a connector between the display and the board to allow easy disassembly.  


One segment on the display went out after a few months and I replaced it during home distractions and discovered the hard way about the lack of polarity protection.  Ordered another display and all has been working well!

I have several QRP transceivers and always use device.  The built in dummy load and SWR bridge make tuning stress free.  I most often use a magloop and the SWR prevents PA damage during tuning.


Re: Wattmeter kit on eBay

Roy Appleton
 

Interesting, looks like someone is selling the old kit that 4 States QRP Group used to sell. Designed by David Cripe.

Roy
WA0YMH

On Mon, Nov 18, 2019, 8:44 PM Mike Reed <n7zef@...> wrote:
I received a kit from eBay that looks interesting and useful. It is an "QRPoMETER Digital 15w QRP wattmeter/ Dummy Load/ VSWR meter. It is $50 plus shipping. Used thru hole parts and a few SMD resistor componets. Docs included. Case is PC boards.
Link is https://www.ebay.com/itm/QRPoMeter-Digital-15W-QRP-Wattmeter-Dummy-Load-VSWR-Meter-Kit/254359954684?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2060353.m2749.l2649
Might be useful for diagnostic or daily use.
 I did include some pics to give an idea of what it is. Sorry for the quality, I am not a picture person.
 73
 Mike - N7ZEF

Wattmeter kit on eBay

Mike Reed
 

I received a kit from eBay that looks interesting and useful. It is an "QRPoMETER Digital 15w QRP wattmeter/ Dummy Load/ VSWR meter. It is $50 plus shipping. Used thru hole parts and a few SMD resistor componets. Docs included. Case is PC boards.
Link is https://www.ebay.com/itm/QRPoMeter-Digital-15W-QRP-Wattmeter-Dummy-Load-VSWR-Meter-Kit/254359954684?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2060353.m2749.l2649
Might be useful for diagnostic or daily use.
 I did include some pics to give an idea of what it is. Sorry for the quality, I am not a picture person.
 73
 Mike - N7ZEF

Re: THANK YOU FOR HELP

harry latterman <harrylatterman@...>
 

oopa...long day my call is NOT K7ZPV... IT IS K7ZOV....DUH...

On Monday, November 18, 2019, 6:13:04 PM MST, harry latterman via Groups.Io <harrylatterman@...> wrote:


To those who got me pointed in the right place to figure out how to build and mod my V3, thank you.  There are not pdf files, but that was not a big deal. I just cut and pasted all the info in a word file and printed it out.  Then save the file as a docx and pdf format just in case. Now I have all I need to build the radio and align it as well as a few different ideas on changes to L5 and L7 to clean up the TX signal.  If anyone has a favorite one let me know. I like the one of winding 12 turns on a T30-6 core. I guess that is what the V5 board is using..

In any case will all the things on my plate right now and with rain and snow coming It will be a while before I get into this radio project.  Should be fun. My end use will be experimenting with WSPR and different antennas and mostly likely FT8.  There will be some SSB and CW also... I was at Harbor Freight today and looking at their ZERO knock off boxes.  Think I will out this board and display in one with a internal battery and manual antenna tuner.  No holes in the case, Everything has to be done with the lid up, as in charging the battery, plugging in a antenna, mic, key and computer.  Making a real EmComm go box. Hopefully with no splatter or very little..

Thank you again I am sure I will have more questions as time goes by.

73 Harry K7ZPV

THANK YOU FOR HELP

harry latterman <harrylatterman@...>
 

To those who got me pointed in the right place to figure out how to build and mod my V3, thank you.  There are not pdf files, but that was not a big deal. I just cut and pasted all the info in a word file and printed it out.  Then save the file as a docx and pdf format just in case. Now I have all I need to build the radio and align it as well as a few different ideas on changes to L5 and L7 to clean up the TX signal.  If anyone has a favorite one let me know. I like the one of winding 12 turns on a T30-6 core. I guess that is what the V5 board is using..

In any case will all the things on my plate right now and with rain and snow coming It will be a while before I get into this radio project.  Should be fun. My end use will be experimenting with WSPR and different antennas and mostly likely FT8.  There will be some SSB and CW also... I was at Harbor Freight today and looking at their ZERO knock off boxes.  Think I will out this board and display in one with a internal battery and manual antenna tuner.  No holes in the case, Everything has to be done with the lid up, as in charging the battery, plugging in a antenna, mic, key and computer.  Making a real EmComm go box. Hopefully with no splatter or very little..

Thank you again I am sure I will have more questions as time goes by.

73 Harry K7ZPV

Re: Edge meter

Christopher J. Shaker, KJ7BLE
 

On 11/18/2019 10:30 AM, Joel Caulkins/N6ALT wrote:
It works!  I just did it to the one that came with my case, however I ended up ordering a Workman CB meter from eBay, it looked much nicer and had the proper scale on it.

Joel
N6ALT

Re: Edge meter

 

Hi Andy,

I'm using the AGC/S-Meter board that came withe the case, it works good. I was able to calibrate it it to a S 9 signal standard so it's very accurate also. It doesn't show SWR, but that could be done with Kits and Parts SWR bridge.

Joel
N6ALT

Re: ubitx version 3 assembly manual

Woody
 

Don't know if there is a formal manual from mfgr., but here are a few places to check...
http://www.hfsignals.com/
http://www.hfsignals.com/index.php/ubitx-r3-archived/
http://ubitx.net/
https://ubitx.net/download/ubitx-v4-mini-manual/

Woody - KZ4AK
kz4ak.com
----------------------------------------------------

On 11/18/2019 20:19, harry latterman via Groups.Io wrote:
Just did a trade for a never been open uBITX ver 3 radio. No manual came with it, just a sealed plastic box with the board and parts.  So where do I download the correct manual for this version in PDF format.

--

Re: ubitx version 3 assembly manual

Jack, W8TEE
 

HFSignals.com is the main source of info on the µBITX. However, ubitx.net is a very valuable resource, too.

Jack, W8TEE

On Monday, November 18, 2019, 3:20:08 PM EST, harry latterman via Groups.Io <harrylatterman@...> wrote:


Just did a trade for a never been open uBITX ver 3 radio. No manual came with it, just a sealed plastic box with the board and parts.  So where do I download the correct manual for this version in PDF format.  I know the radio has issues and can only be upgraded to a V4.  That is not a issue. Once I get it working I will then look into all the up hardware and firmware updates. Thank you for your time and help.

73 Harry K7ZOV

BTW...What's up with the FB people. I have applied to that group twice and never heard anything back.  It is dead or dying or what...

--
Jack, W8TEE

ubitx version 3 assembly manual

harry latterman <harrylatterman@...>
 

Just did a trade for a never been open uBITX ver 3 radio. No manual came with it, just a sealed plastic box with the board and parts.  So where do I download the correct manual for this version in PDF format.  I know the radio has issues and can only be upgraded to a V4.  That is not a issue. Once I get it working I will then look into all the up hardware and firmware updates. Thank you for your time and help.

73 Harry K7ZOV

BTW...What's up with the FB people. I have applied to that group twice and never heard anything back.  It is dead or dying or what...

Re: Edge meter

howard winwood G4GPF
 

I use the AGC kit that the case maker sells, works well (hfsignals)

Re: Edge meter

andy@...
 

Hey Joel I am just wondering what your working with regarding swr meter etc.
An option board of some kind as well?
I am using a uBITX V5 and working well in its stock form with good reports.

Andy VE6KP

Re: Anyone used the ELEKITSORPARTS digital interface board? Opionons? #ubitx #digital

Cory King
 

Ordered mine a few weeks ago and should be in my mailbox any time now.  I'll post back with results -- super excited to get it working.

Re: Edge meter

 

It works!  I just did it to the one that came with my case, however I ended up ordering a Workman CB meter from eBay, it looked much nicer and had the proper scale on it.

Joel
N6ALT

Re: Anyone used the ELEKITSORPARTS digital interface board? Opionons? #ubitx #digital

Justin Phillips K5AXL
 

According to the TI forums, the PCM2904 is natively supported in Linux via standard USB audio class driver


On Mon, Nov 18, 2019, 12:03 PM KG5MG <kg5mg@...> wrote:
From the website it is supported by Windows. Does anyone know if it is supported by any Linux distro?



Sent via the Samsung Galaxy S8+, an AT&T 5G Evolution capable smartphone


-------- Original message --------
From: Michael Bouchereau <captmbouch@...>
Date: 11/18/19 10:35 AM (GMT-06:00)
Subject: Re: [BITX20] Anyone used the ELEKITSORPARTS digital interface board? Opionons? #ubitx #digital

Kit projects has 3 DI kits left in stock. $15 each. + $8 assembled.

Mike
KI5FIS

On Sat, Nov 16, 2019, 11:20 PM Justin Phillips K5AXL <dolmdemon@...> wrote:
Has any used this board in their ubitx, and if so, how's it working? How was the installation? Any gotchas?

https://www.elekitsorparts.com/product/ubitx-digi-interface-module-add-on-board


JP
K5AXL

Re: Anyone used the ELEKITSORPARTS digital interface board? Opionons? #ubitx #digital

KG5MG
 

From the website it is supported by Windows. Does anyone know if it is supported by any Linux distro?



Sent via the Samsung Galaxy S8+, an AT&T 5G Evolution capable smartphone


-------- Original message --------
From: Michael Bouchereau <captmbouch@...>
Date: 11/18/19 10:35 AM (GMT-06:00)
To: BITX20@groups.io
Subject: Re: [BITX20] Anyone used the ELEKITSORPARTS digital interface board? Opionons? #ubitx #digital

Kit projects has 3 DI kits left in stock. $15 each. + $8 assembled.

Mike
KI5FIS

On Sat, Nov 16, 2019, 11:20 PM Justin Phillips K5AXL <dolmdemon@...> wrote:
Has any used this board in their ubitx, and if so, how's it working? How was the installation? Any gotchas?

https://www.elekitsorparts.com/product/ubitx-digi-interface-module-add-on-board


JP
K5AXL

Re: Anyone used the ELEKITSORPARTS digital interface board? Opionons? #ubitx #digital

KG5MG
 

Also interested. I've started assembling but not sure what to do once I'm finished.  I'm hoping it will be self evident but ......



Sent via the Samsung Galaxy S8+, an AT&T 5G Evolution capable smartphone


-------- Original message --------
From: Roy Appleton <twelveoclockhigh@...>
Date: 11/18/19 10:26 AM (GMT-06:00)
To: BITX20@groups.io
Subject: Re: [BITX20] Anyone used the ELEKITSORPARTS digital interface board? Opionons? #ubitx #digital

Sorry. . . "user manual"

Roy
WA0YMH

On Mon, Nov 18, 2019, 10:24 AM Roy Appleton <twelveoclockhigh@...> wrote:
Is there any kind of used manual with this product. The website has lots of fancy phrases and buzz words but I'm not too sure what all it's actually capable of doing? 

Roy
WA0YMH

On Mon, Nov 18, 2019, 2:05 AM <jotukker@...> wrote:
I bought it but still have to built it in, so I can't say how it works.

Greeting Wim (PA1SW)