Date   
Re: Cal Fire Moves to Dismantle Ham Radio System, Endangering Lives Amid Blackouts and Wildfires | Trending

Arv Evans
 

Occasionally there are actions that have great potential to affect ham radio as a whole
but start as small local changes.  Maybe the topic for posts about these events should
be labeled "info-topic" so that those with very narrow fields of interest can avoid reading
them. 

We do have quite a few "off-topic" posts from time to time.  Maybe the solution would
be for moderators to allow the particular topic to run for a few days and then lock the
topic so that no more re-posts on that topic would be allowed.  This seems reasonable
but does potentially block later readers from commenting (good?, bad?).

Arv  K7HKL
_._


On Tue, Oct 15, 2019 at 9:01 PM Ken Hansen <ken@...> wrote:
As an international mail list (reflector) threads like this don't belong here.

It's specific to one state of one country, and there are literally dozens of more suitable venues than this for any discussion of this subject.

How does the policy of CalFire in California, USA Regarding repeater space on public land n the state of California impact the Lithuanian trying to assemble an HF station based on a uBitx or Bitx40?

Re: 80m transmit stopped working, all other bands fine #ubitx-help

Don - KM4UDX
 

Raj and Evan -- I am such an idiot.  It is toooo embarrassing to admit to the mistake I made.

As we all know, WSJT-X allows for setting of power level per band.  I always pay attention to these settings maximizing the prudent RF output per band.  Can you see where this is going? On 80m I failed to catch the low setting on the RF power level in WSJT-X. 

As soon as I use a keyer, not the WSJT-X tune,  the RF was there in abundance.   Am I an idiot? Yes. Is this embarrassing? Yes.

Is the mighty uBITX capable of 24/7 multiband operation for months and months? Well, clearly yes.

I will now slink into the corner....

Thank you all.

Don
km4udx

Re: Cal Fire Moves to Dismantle Ham Radio System,EndangeringLives Amid Blackouts and Wildfires | Trending

Terence Taylor
 

This is a tempest in a teapot. Please see the below information from our section manager:

The State of California has not made any determination we can find "that Ham Radio [is] no longer a benefit. "What happened is that CAL FIRE has transferred responsibility for its communications sites to its property management department.  That department has the task of evaluating each site, its condition, use and tenants.  If a repeater not known to be associated with the emergency management function of a local jurisdiction is found in a CAL FIRE vault, the default action is to move it out or subject it to commercial rental rates.
Our contact in the California Office of Emergency Services suggests that, if any affected repeater is in any way involved with local emergency or government support activity, they should ask that agency to engage with CAL FIRE concerning the repeater.  If the agency makes the case, there is a good chance that the repeater will be unaffected.


On Wednesday, October 16, 2019, 8:29:19 AM PDT, Joe Puma <kd2nfc@...> wrote:


It’s amazing how news travels ala word of mouth or for the internet, social media gossip.  

 

This is what I originally read, then heard conflicting stories. I’m glad I hold reservations to anything I digest over the internet.

 

https://offgridsurvival.com/california-officials-declare-ham-radio-no-longer-a-benefit/

 

 

Joe

KD2NFC

 

Sent from Mail for Windows 10

 

From: Jack, W8TEE via Groups.Io
Sent: Wednesday, October 16, 2019 11:01 AM
To: BITX20@groups.io
Subject: Re: [BITX20] Cal Fire Moves to Dismantle Ham Radio System,EndangeringLives Amid Blackouts and Wildfires | Trending

 

No, it's not a hoax and the ARRL has info posted on it:

 

ARRL officials who have also looked into the situation agree that it’s been blown out of proportion by parties with their own agendas.

“The State of California has not made any determination we can find ‘that Ham Radio [is] no longer a benefit,’” Pacific Division Director Jim Tiemstra, K6JAT, is quoted on the Sacramento Valley Section website. “What happened is that CAL FIRE has transferred responsibility for its communications sites to its property management department. That department has the task of evaluating each site, its condition, use, and tenants. If a repeater not known to be associated with the emergency management function of a local jurisdiction is found in a CAL FIRE vault, the default action is to move it out or subject it to commercial rental rates.”

“Our contact in the California Office of Emergency Services suggests that, if any affected repeater is in any way involved with local emergency or government support activity, they should ask that agency to engage with CAL FIRE concerning the repeater. If the agency makes the case, there is a good chance that the repeater will be unaffected,” Tiemstra added.

ARRL Southwestern Division Director Dick Norton, N6AA, has been responding to inquiries with the same message.

 

I find the section in yellow particularly nettlesome because it looks like a state-agency pissing contest is brewing and that is almost never good for the party in the middle.

 

 

Jack, W8TEE

 

On Wednesday, October 16, 2019, 10:55:23 AM EDT, Joe Puma <kd2nfc@...> wrote:

 

 

Hi Jack,

 

I read that exact article and similar others on the web was a hoax. I really don’t want to dig up where I read this info, it was on other email lists or maybe even Facebook, but I did hear that this info was a hoax.

 

Joe

Kd2nfc

 

Sent from Mail for Windows 10

 

From: Jack, W8TEE via Groups.Io
Sent: Wednesday, October 16, 2019 10:43 AM
To: BITX20@groups.io
Subject: Re: [BITX20] Cal Fire Moves to Dismantle Ham Radio System,Endangering Lives Amid Blackouts and Wildfires | Trending

 

I think you're wrong, Ken. Just because it doesn't directly pertain to someone in Europe doesn't mean those in the US--a fairly large number, BTW--shouldn't hear about it. I'm assuming that those who are not interested in the thread are smart enough not to read it. Also, the US is replete with examples of "one state" setting precedent for other states to follow. Nipping that trend in the bud is often critical and, to do that, one needs to know about the gathering clouds on the horizon.

 

I don't apologize for the posting and see it as keeping fellow hams informed about something that might bite them in the butt down the road.

 

Jack, W8TEE

 

On Tuesday, October 15, 2019, 11:01:42 PM EDT, Ken Hansen <ken@...> wrote:

 

 

As an international mail list (reflector) threads like this don't belong here.

 

It's specific to one state of one country, and there are literally dozens of more suitable venues than this for any discussion of this subject.

 

How does the policy of CalFire in California, USA Regarding repeater space on public land n the state of California impact the Lithuanian trying to assemble an HF station based on a uBitx or Bitx40?

 

It doesn't.

Ken, N2VIP

 

On Oct 15, 2019, at 16:35, Arv Evans <arvid.evans@...> wrote:


--
Jack, W8TEE

 


--
Jack, W8TEE

 

Re: Nearly non-existent output power, no mod

Ted
 

There was no change or adjustment to the firmware between the radio working at 100% of expectations, to the present output deficiency.

I swapped out Q90 to a steel can 2N2222 a while back and all was fine. If there's a preferred upgrade for Q90, I could go back to that stage and work forward again.

Ted
K3RTA

Subscribe

R. Tyson
 

Subscribe
--
R. Tyson <tysons2@...>

Re: Antuino to calculate db loss

iz oos
 

I see. I get - 17db rf out. So I added a non inductive -6db 2ghz attenuator and I get - 20db. Now I see insertion losses.


Il 16/ott/2019 15:34, "Raj vu2zap" <rajendrakumargg@...> ha scritto:
What you read with antuinos In-Out direct connected is base number.

If you base is -21 and you get a reading of -26dbm then your loss is
5db

I wish I has an antuino 30-40 years back!

Have fun
--
Raj

At 16/10/2019, you wrote:

Hi Raj, yesterday when I tried to join the Antuino group I got the answer that my email was already added. But apparently I am not receiving the emails.

The version I have was built in late August and It showed values if I remember right (I have not it here right now) - 19 or - 21db depending on frequency. It is clear to me how to plot and see the readings on different frequencies but I cannot see how to measure the insertion losses eg. Maybe I have just to study the whole messages I missed on the Antuino group!

Il 16/ott/2019 13:18, "Raj vu2zap" < rajendrakumargg@...> ha scritto:
Ooz,
Join us on the antuino group..

Set your center freq, select SNA mode.
Connect filter input to the top (antuino OUT) connecter and filter out to bottom (antuino IN) connector.
click Plot.

The plotted graph has a cursor at the center, you can move the cursor with the knob
and take readings at different spots.

Raj

At 16/10/2019, you wrote:

I mean the loss in db within the passband of the filter. Or a loss in a cable.

Il 16/ott/2019 12:17, "iz oos via Groups.Io" <and2oosiz2= gmail.com@groups.io> ha scritto:
Hello Folks, finally Antuino knocked to my door! I have played with it plotting bandpass and notch filters. Nice and practical, however how do I determine the loss of my filters in terms of db using Antuino? Can you provide a simple example so I can get the trick?


Re: Bitx 40 For Sale

Ted
 

What year is this build, please?  looks nice.

Re: Cal Fire Moves to Dismantle Ham Radio System,EndangeringLives Amid Blackouts and Wildfires | Trending

Joe Puma
 

It’s amazing how news travels ala word of mouth or for the internet, social media gossip.  

 

This is what I originally read, then heard conflicting stories. I’m glad I hold reservations to anything I digest over the internet.

 

https://offgridsurvival.com/california-officials-declare-ham-radio-no-longer-a-benefit/

 

 

Joe

KD2NFC

 

Sent from Mail for Windows 10

 

From: Jack, W8TEE via Groups.Io
Sent: Wednesday, October 16, 2019 11:01 AM
To: BITX20@groups.io
Subject: Re: [BITX20] Cal Fire Moves to Dismantle Ham Radio System,EndangeringLives Amid Blackouts and Wildfires | Trending

 

No, it's not a hoax and the ARRL has info posted on it:

 

ARRL officials who have also looked into the situation agree that it’s been blown out of proportion by parties with their own agendas.

“The State of California has not made any determination we can find ‘that Ham Radio [is] no longer a benefit,’” Pacific Division Director Jim Tiemstra, K6JAT, is quoted on the Sacramento Valley Section website. “What happened is that CAL FIRE has transferred responsibility for its communications sites to its property management department. That department has the task of evaluating each site, its condition, use, and tenants. If a repeater not known to be associated with the emergency management function of a local jurisdiction is found in a CAL FIRE vault, the default action is to move it out or subject it to commercial rental rates.”

“Our contact in the California Office of Emergency Services suggests that, if any affected repeater is in any way involved with local emergency or government support activity, they should ask that agency to engage with CAL FIRE concerning the repeater. If the agency makes the case, there is a good chance that the repeater will be unaffected,” Tiemstra added.

ARRL Southwestern Division Director Dick Norton, N6AA, has been responding to inquiries with the same message.

 

I find the section in yellow particularly nettlesome because it looks like a state-agency pissing contest is brewing and that is almost never good for the party in the middle.

 

 

Jack, W8TEE

 

On Wednesday, October 16, 2019, 10:55:23 AM EDT, Joe Puma <kd2nfc@...> wrote:

 

 

Hi Jack,

 

I read that exact article and similar others on the web was a hoax. I really don’t want to dig up where I read this info, it was on other email lists or maybe even Facebook, but I did hear that this info was a hoax.

 

Joe

Kd2nfc

 

Sent from Mail for Windows 10

 

From: Jack, W8TEE via Groups.Io
Sent: Wednesday, October 16, 2019 10:43 AM
To: BITX20@groups.io
Subject: Re: [BITX20] Cal Fire Moves to Dismantle Ham Radio System,Endangering Lives Amid Blackouts and Wildfires | Trending

 

I think you're wrong, Ken. Just because it doesn't directly pertain to someone in Europe doesn't mean those in the US--a fairly large number, BTW--shouldn't hear about it. I'm assuming that those who are not interested in the thread are smart enough not to read it. Also, the US is replete with examples of "one state" setting precedent for other states to follow. Nipping that trend in the bud is often critical and, to do that, one needs to know about the gathering clouds on the horizon.

 

I don't apologize for the posting and see it as keeping fellow hams informed about something that might bite them in the butt down the road.

 

Jack, W8TEE

 

On Tuesday, October 15, 2019, 11:01:42 PM EDT, Ken Hansen <ken@...> wrote:

 

 

As an international mail list (reflector) threads like this don't belong here.

 

It's specific to one state of one country, and there are literally dozens of more suitable venues than this for any discussion of this subject.

 

How does the policy of CalFire in California, USA Regarding repeater space on public land n the state of California impact the Lithuanian trying to assemble an HF station based on a uBitx or Bitx40?

 

It doesn't.

Ken, N2VIP

 

On Oct 15, 2019, at 16:35, Arv Evans <arvid.evans@...> wrote:


--
Jack, W8TEE

 


--
Jack, W8TEE

 

Re: 80m transmit stopped working, all other bands fine #ubitx-help

Evan Hand
 

I would suspect that KT3 has a bad contact in that it is switching, but one of the two are not connecting causing an open line to the antenna.  If this is true, I would be sure to fix it before doing any long transmissions.  With the PA power connected, verify that you are drawing current on the PA power input.  You should see current draw on transmit.  Then I would verify that the contacts switch on KT3 with the PA power disconnected.  This can be checked with just your dvm.

NOTE: with the PA power disconnected, you can key the transmitter with either the mic or the CW key to verify the relay switching.

How are you verifying the power out, and more importantly, which version?  KT3 is for the v3 or v4 ubitx on 80 meters. KC1 is the relay on the v5.

73
Evan
AC9TU

Re: 80m transmit stopped working, all other bands fine #ubitx-help

 

At 16/10/2019, you wrote:
After 4 months of almost 24/7 wspr operation with a high percent of TX time, the 80m TX has failed.
Check the high band relays!

Raj

Re: Cal Fire Moves to Dismantle Ham Radio System,Endangering Lives Amid Blackouts and Wildfires | Trending

Jack, W8TEE
 

No, it's not a hoax and the ARRL has info posted on it:

ARRL officials who have also looked into the situation agree that it’s been blown out of proportion by parties with their own agendas.

“The State of California has not made any determination we can find ‘that Ham Radio [is] no longer a benefit,’” Pacific Division Director Jim Tiemstra, K6JAT, is quoted on the Sacramento Valley Section website. “What happened is that CAL FIRE has transferred responsibility for its communications sites to its property management department. That department has the task of evaluating each site, its condition, use, and tenants. If a repeater not known to be associated with the emergency management function of a local jurisdiction is found in a CAL FIRE vault, the default action is to move it out or subject it to commercial rental rates.”

“Our contact in the California Office of Emergency Services suggests that, if any affected repeater is in any way involved with local emergency or government support activity, they should ask that agency to engage with CAL FIRE concerning the repeater. If the agency makes the case, there is a good chance that the repeater will be unaffected,” Tiemstra added.

ARRL Southwestern Division Director Dick Norton, N6AA, has been responding to inquiries with the same message.


I find the section in yellow particularly nettlesome because it looks like a state-agency pissing contest is brewing and that is almost never good for the party in the middle.


Jack, W8TEE

On Wednesday, October 16, 2019, 10:55:23 AM EDT, Joe Puma <kd2nfc@...> wrote:


Hi Jack,

 

I read that exact article and similar others on the web was a hoax. I really don’t want to dig up where I read this info, it was on other email lists or maybe even Facebook, but I did hear that this info was a hoax.

 

Joe

Kd2nfc

 

Sent from Mail for Windows 10

 

From: Jack, W8TEE via Groups.Io
Sent: Wednesday, October 16, 2019 10:43 AM
To: BITX20@groups.io
Subject: Re: [BITX20] Cal Fire Moves to Dismantle Ham Radio System,Endangering Lives Amid Blackouts and Wildfires | Trending

 

I think you're wrong, Ken. Just because it doesn't directly pertain to someone in Europe doesn't mean those in the US--a fairly large number, BTW--shouldn't hear about it. I'm assuming that those who are not interested in the thread are smart enough not to read it. Also, the US is replete with examples of "one state" setting precedent for other states to follow. Nipping that trend in the bud is often critical and, to do that, one needs to know about the gathering clouds on the horizon.

 

I don't apologize for the posting and see it as keeping fellow hams informed about something that might bite them in the butt down the road.

 

Jack, W8TEE

 

On Tuesday, October 15, 2019, 11:01:42 PM EDT, Ken Hansen <ken@...> wrote:

 

 

As an international mail list (reflector) threads like this don't belong here.

 

It's specific to one state of one country, and there are literally dozens of more suitable venues than this for any discussion of this subject.

 

How does the policy of CalFire in California, USA Regarding repeater space on public land n the state of California impact the Lithuanian trying to assemble an HF station based on a uBitx or Bitx40?

 

It doesn't.

Ken, N2VIP



On Oct 15, 2019, at 16:35, Arv Evans <arvid.evans@...> wrote:


--
Jack, W8TEE

 


--
Jack, W8TEE

Re: Cal Fire Moves to Dismantle Ham Radio System,Endangering Lives Amid Blackouts and Wildfires | Trending

Joe Puma
 

Hi Jack,

 

I read that exact article and similar others on the web was a hoax. I really don’t want to dig up where I read this info, it was on other email lists or maybe even Facebook, but I did hear that this info was a hoax.

 

Joe

Kd2nfc

 

Sent from Mail for Windows 10

 

From: Jack, W8TEE via Groups.Io
Sent: Wednesday, October 16, 2019 10:43 AM
To: BITX20@groups.io
Subject: Re: [BITX20] Cal Fire Moves to Dismantle Ham Radio System,Endangering Lives Amid Blackouts and Wildfires | Trending

 

I think you're wrong, Ken. Just because it doesn't directly pertain to someone in Europe doesn't mean those in the US--a fairly large number, BTW--shouldn't hear about it. I'm assuming that those who are not interested in the thread are smart enough not to read it. Also, the US is replete with examples of "one state" setting precedent for other states to follow. Nipping that trend in the bud is often critical and, to do that, one needs to know about the gathering clouds on the horizon.

 

I don't apologize for the posting and see it as keeping fellow hams informed about something that might bite them in the butt down the road.

 

Jack, W8TEE

 

On Tuesday, October 15, 2019, 11:01:42 PM EDT, Ken Hansen <ken@...> wrote:

 

 

As an international mail list (reflector) threads like this don't belong here.

 

It's specific to one state of one country, and there are literally dozens of more suitable venues than this for any discussion of this subject.

 

How does the policy of CalFire in California, USA Regarding repeater space on public land n the state of California impact the Lithuanian trying to assemble an HF station based on a uBitx or Bitx40?

 

It doesn't.

Ken, N2VIP



On Oct 15, 2019, at 16:35, Arv Evans <arvid.evans@...> wrote:


--
Jack, W8TEE

 

Re: Cal Fire Moves to Dismantle Ham Radio System, Endangering Lives Amid Blackouts and Wildfires | Trending

Jack, W8TEE
 

I think you're wrong, Ken. Just because it doesn't directly pertain to someone in Europe doesn't mean those in the US--a fairly large number, BTW--shouldn't hear about it. I'm assuming that those who are not interested in the thread are smart enough not to read it. Also, the US is replete with examples of "one state" setting precedent for other states to follow. Nipping that trend in the bud is often critical and, to do that, one needs to know about the gathering clouds on the horizon.

I don't apologize for the posting and see it as keeping fellow hams informed about something that might bite them in the butt down the road.

Jack, W8TEE

On Tuesday, October 15, 2019, 11:01:42 PM EDT, Ken Hansen <ken@...> wrote:


As an international mail list (reflector) threads like this don't belong here.

It's specific to one state of one country, and there are literally dozens of more suitable venues than this for any discussion of this subject.

How does the policy of CalFire in California, USA Regarding repeater space on public land n the state of California impact the Lithuanian trying to assemble an HF station based on a uBitx or Bitx40?

It doesn't.

Ken, N2VIP

On Oct 15, 2019, at 16:35, Arv Evans <arvid.evans@...> wrote:


--
Jack, W8TEE

80m transmit stopped working, all other bands fine #ubitx-help

Don - KM4UDX
 

After 4 months of almost 24/7 wspr operation with a high percent of TX time, the 80m TX has failed.

All the other bands are great. And on 80m, the TX/RX relay snaps like it should, just like it does on all the other bands, but there is no RF output.

I know I have (over?) used my beloved uBITX with 24/7 WSPR operation. And now I have a failure.

Is there a debug process I can use to isolate the fault, or is it 99% likely to be part ______?

I have just a DVM for test equipment. so no fancy RF probes, and no scope. Guidance oh wise ones?

Just fyi, here is a chart of my WSPR spot 2-way rankings by month. I think I have plateaued.

Re: UBitx v5 Not Saving Calibration or BFO adjustments with CEC v 1.20 Nextion

markix88@...
 

finally I found the problem...it was my BFO off...(11.053 i think, as factory); i set new value (reference with 1000 Hz USB with the RWM time station at 9.996 KHz carrier) and now rx is perfect and saved (new value is something about 11.055 etc)...I don't know why i was convinced it was a problem with master calibration value...with the BFO calibration all saved with success, with master cal don't save anything...this evening i will try audio and frequency output and I will see if it's all OK, thank you to all for support !

Re: Antuino to calculate db loss

 

What you read with antuinos In-Out direct connected is base number.

If you base is -21 and you get a reading of -26dbm then your loss is
5db

I wish I has an antuino 30-40 years back!

Have fun
--
Raj


At 16/10/2019, you wrote:

Hi Raj, yesterday when I tried to join the Antuino group I got the answer that my email was already added. But apparently I am not receiving the emails.

The version I have was built in late August and It showed values if I remember right (I have not it here right now) - 19 or - 21db depending on frequency. It is clear to me how to plot and see the readings on different frequencies but I cannot see how to measure the insertion losses eg. Maybe I have just to study the whole messages I missed on the Antuino group!

Il 16/ott/2019 13:18, "Raj vu2zap" < rajendrakumargg@...> ha scritto:
Ooz,
Join us on the antuino group..

Set your center freq, select SNA mode.
Connect filter input to the top (antuino OUT) connecter and filter out to bottom (antuino IN) connector.
click Plot.

The plotted graph has a cursor at the center, you can move the cursor with the knob
and take readings at different spots.

Raj

At 16/10/2019, you wrote:

I mean the loss in db within the passband of the filter. Or a loss in a cable.

Il 16/ott/2019 12:17, "iz oos via Groups.Io" <and2oosiz2= gmail.com@groups.io> ha scritto:
Hello Folks, finally Antuino knocked to my door! I have played with it plotting bandpass and notch filters. Nice and practical, however how do I determine the loss of my filters in terms of db using Antuino? Can you provide a simple example so I can get the trick?

Re: Antuino to calculate db loss

iz oos
 

Hi Raj, yesterday when I tried to join the Antuino group I got the answer that my email was already added. But apparently I am not receiving the emails.

The version I have was built in late August and It showed values if I remember right (I have not it here right now) - 19 or - 21db depending on frequency. It is clear to me how to plot and see the readings on different frequencies but I cannot see how to measure the insertion losses eg. Maybe I have just to study the whole messages I missed on the Antuino group!


Il 16/ott/2019 13:18, "Raj vu2zap" <rajendrakumargg@...> ha scritto:
Ooz,
Join us on the antuino group..

Set your center freq, select SNA mode.
Connect filter input to the top (antuino OUT) connecter and filter out to bottom (antuino IN) connector.
click Plot.

The plotted graph has a cursor at the center, you can move the cursor with the knob
and take readings at different spots.

Raj

At 16/10/2019, you wrote:

I mean the loss in db within the passband of the filter. Or a loss in a cable.

Il 16/ott/2019 12:17, "iz oos via Groups.Io" <and2oosiz2= gmail.com@groups.io> ha scritto:

Hello Folks, finally Antuino knocked to my door! I have played with it plotting bandpass and notch filters. Nice and practical, however how do I determine the loss of my filters in terms of db using Antuino? Can you provide a simple example so I can get the trick?

Re: OT: Yahoo Groups is going away

Michael Walker
 

Thanks Terry

Like other groups that have migrated to groups.io, will this group be doing the same thing as they have tools to easily migrate?

If so, would the files be migrated over ?

I am not sure who the moderators are, but if they do not have time to do it, I am sure there are others that might volunteer.

73, Mike va3mw

On Tue, Oct 15, 2019 at 8:51 PM Terry VK5TM <vk5tm@...> wrote:
Yahoo Groups is going away.

If you need any files, photo's or other data from any group you are member of, get it now, by the end of December it will all be gone.

Terry VK5TM

Re: OT: our group founder Hans wins Homebrew Heros' first award!

Jorge Luiz Fenerich
 

     Congratulations Hans, always great to be recognized for your work, I admire people like you and Ashhar Farhan, the amateurs of the world thank you for your work.
     73 by Jorge PY2PVT _._

Em ter, 15 de out de 2019 às 23:32, Ashhar Farhan <farhanbox@...> escreveu:

Hans, who has been a source of major inspiration for us all has been recognised as a homebrew hero. 

Though now known for his qrp lab kits, he has amazing stamina to get to the bottom of things and uncover new stuff. His website is a treasure trove of information that he has gleaned. From using LEDs as varactors to measuring phase noise to bulding his own oscilloscope, his work us mind blowing.

Yes, he started this group too. Congratulations Hans, you have always been my hero!

- f



--
  73 de Jorge PY2PVT
  Campinas SP
  GG67MD

Re: Cal Fire Moves to Dismantle Ham Radio System, Endangering Lives Amid Blackouts and Wildfires | Trending

Edward Reynolds
 

I agree that while this is not the forum for local government issues, I’m glad it was posted. We in the state of Oregon probably would not have heard about this issue. Thankfully the Oregon leaders realize the reliability of the ham repeaters and their roll in times of backup communication needs vs a system that is over priced and not reliable.
Thanks to the group for their time, I read every post on this site, lots of great information I’ve got a UBITX ver. 5 I’m playing with. Keep up the great posts
Cheers
Ed N7SNT 


On Oct 15, 2019, at 9:31 PM, Jerry Gaffke via Groups.Io <jgaffke@...> wrote:

Normally you could take this up with the group moderator.
But in this case, perhaps your best plan is to start your own forum.  ;-)

95% of the messages here aren't of much interest to me.
That's OK.
So long as it remains civil.
Think I"ll go get a beer and kick off this thread again:  https://groups.io/g/BITX20/topic/18584402 

Jerry, KE7ER


On Tue, Oct 15, 2019 at 08:01 PM, Ken Hansen wrote:
As an international mail list (reflector) threads like this don't belong here.
 
It's specific to one state of one country, and there are literally dozens of more suitable venues than this for any discussion of this subject.
 
How does the policy of CalFire in California, USA Regarding repeater space on public land n the state of California impact the Lithuanian trying to assemble an HF station based on a uBitx or Bitx40?
 
It doesn't.

Ken, N2VIP