|
Re: uBitX V6 no transmit power
#ubitxv6
#ubitx-help
#tx
Aaron,
I was going off of the numbers given on the HF Signals schematic (they are the same for all version since 4 that I know of):
You will need to trace out the wiring on the board to find the
Aaron,
I was going off of the numbers given on the HF Signals schematic (they are the same for all version since 4 that I know of):
You will need to trace out the wiring on the board to find the
|
By
Evan Hand
·
#81960
·
|
|
Re: uBitX V6 no transmit power
#ubitxv6
#ubitx-help
#tx
Just some very simple tests that others have previously been posted. They worked for me.
With your meter connected blow fairly hard into your microphone. Another test is to enable morse code and using
Just some very simple tests that others have previously been posted. They worked for me.
With your meter connected blow fairly hard into your microphone. Another test is to enable morse code and using
|
By
Owen Vinall
·
#81959
·
|
|
Re: Assembly instructions for the ubitx v4
Mario,
Before working on the AGC wiring, I would make sure the audio amp and the rest of the rig is working.
I assume that you will be using the Front Panel PCB supplied and that you have solder
Mario,
Before working on the AGC wiring, I would make sure the audio amp and the rest of the rig is working.
I assume that you will be using the Front Panel PCB supplied and that you have solder
|
By
Evan Hand
·
#81958
·
|
|
Re: uBitX V6 no transmit power
#ubitxv6
#ubitx-help
#tx
Evan,
K1 does not have a Pin 12
--
'72
Aaron Scott
The K5ATG Blog
Mid-Del Amateur Radio Club
QRPARCI# 16443
GQRP# 16389
4SQRP # 1080
Evan,
K1 does not have a Pin 12
--
'72
Aaron Scott
The K5ATG Blog
Mid-Del Amateur Radio Club
QRPARCI# 16443
GQRP# 16389
4SQRP # 1080
|
By
Aaron K5ATG
·
#81957
·
|
|
Re: ubitx nextion case for 4.3 inch display schematic required
Hello,
Am 20.08.2020 05:40, schrieb vu3gwn:
[...]
Do you have a AGC too?
[...]
73
Mario Koppensteiner
OE5MKE
Hello,
Am 20.08.2020 05:40, schrieb vu3gwn:
[...]
Do you have a AGC too?
[...]
73
Mario Koppensteiner
OE5MKE
|
By
Mario Koppensteiner
·
#81956
·
|
|
Re: Assembly instructions for the ubitx v4
Hello Evan,
Am 16.08.2020 12:59, schrieb Evan Hand:
I saw this page already. I does not explain how to connect the AGC and the AMP to the board.
I'll have a try when I have connected all the
Hello Evan,
Am 16.08.2020 12:59, schrieb Evan Hand:
I saw this page already. I does not explain how to connect the AGC and the AMP to the board.
I'll have a try when I have connected all the
|
By
Mario Koppensteiner
·
#81955
·
|
|
Re: Assembly instructions for the ubitx v4
Hello Mark,
Am 17.08.2020 14:43, schrieb Mark M.:
thank you for your response.
I still need to know how to connect the AGC and the AMP to the ubitx board.
73
Mario Koppensteiner
OE5MKE
Hello Mark,
Am 17.08.2020 14:43, schrieb Mark M.:
thank you for your response.
I still need to know how to connect the AGC and the AMP to the ubitx board.
73
Mario Koppensteiner
OE5MKE
|
By
Mario Koppensteiner
·
#81954
·
|
|
Re: Assembly instructions for the ubitx v4
Hello Evan,
Am 17.08.2020 13:23, schrieb Evan Hand:
Yes I have.
Sorry for the confusion. The part has 5 terminals. That's true.l
I saw this already in the documentation. On the first pdf there are
Hello Evan,
Am 17.08.2020 13:23, schrieb Evan Hand:
Yes I have.
Sorry for the confusion. The part has 5 terminals. That's true.l
I saw this already in the documentation. On the first pdf there are
|
By
Mario Koppensteiner
·
#81953
·
|
|
Re: Assembly instructions for the ubitx v4
Hello Bob,
Am 16.08.2020 03:22, schrieb Bob Lunsford via groups.io:
Did you are the AGC and the AMP too?
[...]
73
Mario Koppensteiner
OE5MKE
Hello Bob,
Am 16.08.2020 03:22, schrieb Bob Lunsford via groups.io:
Did you are the AGC and the AMP too?
[...]
73
Mario Koppensteiner
OE5MKE
|
By
Mario Koppensteiner
·
#81952
·
|
|
Re: Assembly instructions for the ubitx v4
Hello Rick,
Am 20.08.2020 00:40, schrieb Rick Price:
Hello Mario,
Yes, I saw in one of your messages after I sent the file that you had a
nextion case from amateurradio kits. If you
Hello Rick,
Am 20.08.2020 00:40, schrieb Rick Price:
Hello Mario,
Yes, I saw in one of your messages after I sent the file that you had a
nextion case from amateurradio kits. If you
|
By
Mario Koppensteiner
·
#81951
·
|
|
Re: LTSpice 17
On Mon, Sep 14, 2020 at 11:49 AM, Gerard wrote:
try LTSpice 17, you can simulate electronic circuits.
See examples on the softYour message is a great reminder that I need to get back to learning
On Mon, Sep 14, 2020 at 11:49 AM, Gerard wrote:
try LTSpice 17, you can simulate electronic circuits.
See examples on the softYour message is a great reminder that I need to get back to learning
|
By
Tom, wb6b
·
#81950
·
|
|
Re: Replacing SMD component
Congratulations.
I also use a toothpick and paper glue stick.
I just ut the toothpick point in the stick, then on the component and put it in place
Regards
Lawrence
Congratulations.
I also use a toothpick and paper glue stick.
I just ut the toothpick point in the stick, then on the component and put it in place
Regards
Lawrence
|
By
Lawrence Galea
·
#81949
·
|
|
MSHV SOFTWARE FOR FT8 VERSION
ALL,
COULD ANYONE INDICATE THE BEST VERSION OF THE MSHV SOFTWARE FOR FT8, TO BE INSTALLED ON uBITX V4?
--73's de Rubens PY2PVB
GG49In - Ilha Solteira SP Brazil
ALL,
COULD ANYONE INDICATE THE BEST VERSION OF THE MSHV SOFTWARE FOR FT8, TO BE INSTALLED ON uBITX V4?
--73's de Rubens PY2PVB
GG49In - Ilha Solteira SP Brazil
|
By
Rubens Kamimura
·
#81948
·
|
|
Re: Cw not working with straight key
Nigel,
Just checked sotabeams site again and this time it responded. That filter has a message stating that more stock is due in Autumn.
Reg G4NFR
Nigel,
Just checked sotabeams site again and this time it responded. That filter has a message stating that more stock is due in Autumn.
Reg G4NFR
|
By
R. Tyson
·
#81947
·
|
|
LTSpice 17
hello,
i think you know some software helpfull like RFSim99, Dishal, Tore calculator.
try LTSpice 17, you can simulate electronic circuits.
See examples on the soft
cdt
hello,
i think you know some software helpfull like RFSim99, Dishal, Tore calculator.
try LTSpice 17, you can simulate electronic circuits.
See examples on the soft
cdt
|
By
Gerard
·
#81946
·
|
|
Re: Cw not working with straight key
Hi Nigel,
The two stage filter I used came from -
https://www.sotabeams.co.uk/audio-filters-and-more/
I gather you have already looked at them ? They do a couple of cheaper dual
Hi Nigel,
The two stage filter I used came from -
https://www.sotabeams.co.uk/audio-filters-and-more/
I gather you have already looked at them ? They do a couple of cheaper dual
|
By
R. Tyson
·
#81945
·
|
|
Re: Please explain to me how works the VFO's
hello,
I re-checked the pcb. The cabling is correct.
For me, there is only one solution: Replace the 2n3904. they may be of poor quality. I don’t have a bfr at my fingertips, but I’m going to do a
hello,
I re-checked the pcb. The cabling is correct.
For me, there is only one solution: Replace the 2n3904. they may be of poor quality. I don’t have a bfr at my fingertips, but I’m going to do a
|
By
Gerard
·
#81944
·
|
|
Re: Cw not working with straight key
Hello Reg and advance apologies to Dave for semi hijacking topic.
Please can you provide more details re the 2 stage CW filter added?
I am busy building my v3 uBtix enclosure and pondering options
Hello Reg and advance apologies to Dave for semi hijacking topic.
Please can you provide more details re the 2 stage CW filter added?
I am busy building my v3 uBtix enclosure and pondering options
|
By
Nigel ZS6RN
·
#81943
·
|
|
Re: uBITX V6 setup for digital modes
#digital
#ubitxv6
I use the Easy-Digi with a USB to Serial adapter and it works well. You can order them already built to work with any radio I think with the USB interface built in. I used the built board and added my
I use the Easy-Digi with a USB to Serial adapter and it works well. You can order them already built to work with any radio I think with the USB interface built in. I used the built board and added my
|
By
mark bodlovich
·
#81942
·
|
|
Re: BitX40 Frequency stability problem
John,
I also have the bitX 40 and the V6 versions.
Since as you say , it’s been sitting a while . Did you try rocking re-seating / cleaning all connectors / display board?
Oxidation of some
John,
I also have the bitX 40 and the V6 versions.
Since as you say , it’s been sitting a while . Did you try rocking re-seating / cleaning all connectors / display board?
Oxidation of some
|
By
Jeff Debes <jeff.debes@...>
·
#81941
·
|