Date   
Re: new V6 owner with a few basic questions on wiring and software #v6

support@...
 

Hello Tim,

Yes the jam nut for the volume control is not needed for the V6 Full Kit but has been included anyway just in case one would want to change the front panel. This is a part of the standard Basic kit and we have also included it for the Full Kit that comes with an additional case as well. But its not needed.

Hope that helps.

Regards,

Thomas
--
Support@...

Re: V5 not receiving local am stations

Maurice Bersan <Vk6hly@...>
 

Solved!
Thanks to all who helped.
It turned out to be my manual antenna tuner not being able to tune in MW. I connected my antenna straight in to my ubitx and all those MW broadcast stations came to life.
Someone on this forum did mention my antenna, I should of listened earlier. 
Cheers
Maurice
Vk6hly

Re: Frequency and BFO alignment of uBITX v6

Ashhar Farhan
 

Hmm.. I should have thought of that! 


On Wed 26 Feb, 2020, 2:31 AM Reed N, <greenkid336600+groupsio@...> wrote:
Great video! Clear visuals and explanations.

One detail that probably would be good to add is about the side band inversion if the BFO is tuned "backwards".


Reed

Re: uk builders

Ben Holmes
 

I just bought this one from Ebay for just under $30. It's rather large, and my intent is to have a lot of fun with mods... this will give me plenty of room. Perhaps bigger than you would want, depending on what you're looking for.

Do a search for this:

Blue Metal Electronic Enclosure Project Case DIY Junction Box 310 x 285 x 115mm
:

Re: RX #V6 quits working when ant coax braid is connected #v6

Andy_501 <andrew.webb.501.ve4per@...>
 

Sat down to give some troubleshooting efforts a whirl and darn just started working normally again ; hard to troubleshoot something intermittent like that. GRRRR

On 2020-02-25 11:38 a.m., Andy_501 via Groups.Io wrote:
Not recently, but yes I did in late summer 2018. I am inclined to believe it was kind of a multiple associated hit of side forks from a main fork that struck all rooftop antennas (SAT TV, Inet Radio Link, OTA rooftop TV antenna and possibly a ham antenna) simultaneously. I don't think it was a full hit of a main lightning bolt because likely that would have set fire to my residence as well.

  It took out ISP's POE internet antenna interface unit, two HDMI input ports one each in two smart TV's, two wired ethernet NIC cards in two separate PC's , and two video adapter display output ports on another two PC's (network file share server and NLE editing workstation).

My main ham PC USB onboard interfaces/hub disabling the PC entirely (had to replace it) the main LR TV satellite TV receiver, a yamaha two channel USB audio mixer, a Yaesu CAT cable and a SignalinkUSB sound device and I suspect RF input to my FT857.  It took almost 6-8 months to find each of the failed components and replace them one at a time and get back to now where it is almost all, except for the possible protector block in the coax switch, to serviceable. Ham PC new one is a refurbished one about $275 Cdn, FT857 repairs $300 + shipping both ways, Yamaha mixer and Sat TV receiver were under warranty, SignalinkUSB was $175 + $75 for replacement PCB for damaged one (so I could repair it myself but didn't find out I could until after a replacement unit was paid for and shipped to me) .

I was sitting in an armchair at 3:00 AM reading when the bolt struck, and I could tell by the sound of it that likely something might be affected, but had no idea how extensive the final end effects were going to be.

Home network ethernet cables close by runs of audio and USB cables and because it was all close to the ham PC onboard USB hub and network cabling the one hit was able to be induced into so many places because of so many interconnections.

It was not apparent immediately that there was widespread damage to so many components but it did demonstrate how it's effects can be transmitted/induced in so many directions at once and being like a major static discharge any module with any CMOS components at all can be damaged and not show up for a long time.

I had worked in electronics and communications facilities for 35 yrs and never seen such widespread damage as this anywhere. Usually it was just replacing carbon protector blocks or heat coils in landline termination points and reboot a system to be back in business; no such luck in this case.

When I had the SAT TV dish and receiver installed the Bell service tech did not install a ground; I had to fight with Bell engineering management to get them to install one and even then they only put in a 40' run of #16 guage insulated hookup wire as a ground when it should have been in my opinion #6 bare copper stranded ground cable. But then who am I right?

Lightning is very weird, expensive and not a ham's friend at all.





On 2020-02-25 4:58 a.m., Raj vu2zap wrote:
Seriously, did you have a thunderstorm ?

At 25-02-20, you wrote:
Yes I was wondering about something like a lightning hit blowing the surge protector built into the switch so went to check and discovered the radio doesn't even turn on now so tomorrow likely I will have to replace a fuse in the external power supply; just hope the rig wasn't damaged. GRRRRRR I was just getting close enough to try a QSO or two.


On 2020-02-25 1:22 a.m., Raj vu2zap wrote:
Andy,

Remove the jumper cable between the coax switch and the rig and check for a short.
Happened to me..

Raj

At 25-02-20, you wrote:
The rig goes through a coax switch which I can select a 40 M Hamstick whip, a 20 M small loop antenna, and/or 100 W 50 Ohm dummy load. Doesn't matter which ant is selected same situation so it would seem voltage difference would be the most likely place to start.

Power supply is plugged into UPS but antenna grounds are all direct to a dedicated ground rod for radio gear alone. So might be a potential difference between radio ground rod and electrical utility ground rods.

Thanks for the tip Raj

On 2020-02-24 10:50 p.m., Raj vu2zap wrote:
Andy,

I suspect that your antenna cable is shorted or there is a voltage difference between
your ground and your power supply -ve

When partially plugged in the system behaves like a long wire.

See if your antenna is working with another radio.

Raj

At 25-02-20, you wrote:
I finished setting up the rig and moved it into the shack to put it on full blown antenna expecting some better signals that the minor few available from the temp mag mount HF vert on metal deep freeze lid conterpoise.

When center conductor is inserted 60-80 % inserted signals are evident and AM broadcast stations within 100 mi are easily received and BFO calibration can be adjusted properly. But as soon as the connector is fully inserted in antenna and ground braid makes solid connection signals disappear on all bands and there seems to be a flicker in the display. On a couple of occasions the display completely blanks and goes white. Power off reset then restores display but not the signals until coax outer conductor is disconnected. Seems like some sort of ground loop almost connecting through the input????


Any pointers??

Andy VE4PER

Re: Size and type of USB program cable

Ben Holmes
 

This is what I bought from Ebay - cost $3.89:

USB CAMERA CABLE 6FT CORD USB 2.0 HIGH SPEED TYPE A MALE TO MINI-B 5P MALE

If you search for that phrase, you should find just what you need.

 

Re: #ubitxv6 frequency calibration #ubitx #v6 #calibration #ubitxv6

Reed N
 

Hi Felipe,

If you haven't already, check out Ashhar's new video tutorial: https://groups.io/g/BITX20/message/76434


Reed

Re: Uploading firmware to ubitx

Reed N
 

Another great tutorial video.

One missing piece: on my version of the IDE, you need to select the "ATmega328p (old bootloader)" version. I know that's caught a couple people.


Reed

Re: Frequency and BFO alignment of uBITX v6

Reed N
 

Great video! Clear visuals and explanations.

One detail that probably would be good to add is about the side band inversion if the BFO is tuned "backwards".


Reed

Re: Size and type of USB program cable

David Nelson
 

According to Ashars video it is an usb mini. The same as used with the arduino. dave kc2ipx


On Tue, Feb 25, 2020 at 12:44 PM Andy_501 <andrew.webb.501.ve4per@...> wrote:

Hi Ralph,

I bought a special one so I can use an android phone to do a reset of the nano using the phone if needed. It was an 18 inch USB mini to USB micro connector adapter cable; the mini connects to the phone and the micro to the rig. It was about $15 and they said if I wanted a 3 ft or 6ft one the costs jumps up to $50-$60 range. Not a common one for sure.

On 2020-02-25 11:07 a.m., Ralph King via Groups.Io wrote:
Just got my BITX V6 today.  Put it together and it works just fine. I have one question.
On the USB program cable that plugs into the back, what size and type plug do I need ? 
I looked in my drawer of cables, and all of the plugs that I have are too small to fit.

Thanks in advance

Ralph  K1KOB  r.rking41@... 

Re: Size and type of USB program cable

Andy_501 <andrew.webb.501.ve4per@...>
 

Hi Ralph,

I bought a special one so I can use an android phone to do a reset of the nano using the phone if needed. It was an 18 inch USB mini to USB micro connector adapter cable; the mini connects to the phone and the micro to the rig. It was about $15 and they said if I wanted a 3 ft or 6ft one the costs jumps up to $50-$60 range. Not a common one for sure.

On 2020-02-25 11:07 a.m., Ralph King via Groups.Io wrote:
Just got my BITX V6 today.  Put it together and it works just fine. I have one question.
On the USB program cable that plugs into the back, what size and type plug do I need ? 
I looked in my drawer of cables, and all of the plugs that I have are too small to fit.

Thanks in advance

Ralph  K1KOB  r.rking41@... 

Re: RX #V6 quits working when ant coax braid is connected #v6

Andy_501 <andrew.webb.501.ve4per@...>
 

Not recently, but yes I did in late summer 2018. I am inclined to believe it was kind of a multiple associated hit of side forks from a main fork that struck all rooftop antennas (SAT TV, Inet Radio Link, OTA rooftop TV antenna and possibly a ham antenna) simultaneously. I don't think it was a full hit of a main lightning bolt because likely that would have set fire to my residence as well.

  It took out ISP's POE internet antenna interface unit, two HDMI input ports one each in two smart TV's, two wired ethernet NIC cards in two separate PC's , and two video adapter display output ports on another two PC's (network file share server and NLE editing workstation).

My main ham PC USB onboard interfaces/hub disabling the PC entirely (had to replace it) the main LR TV satellite TV receiver, a yamaha two channel USB audio mixer, a Yaesu CAT cable and a SignalinkUSB sound device and I suspect RF input to my FT857.  It took almost 6-8 months to find each of the failed components and replace them one at a time and get back to now where it is almost all, except for the possible protector block in the coax switch, to serviceable. Ham PC new one is a refurbished one about $275 Cdn, FT857 repairs $300 + shipping both ways, Yamaha mixer and Sat TV receiver were under warranty, SignalinkUSB was $175 + $75 for replacement PCB for damaged one (so I could repair it myself but didn't find out I could until after a replacement unit was paid for and shipped to me) .

I was sitting in an armchair at 3:00 AM reading when the bolt struck, and I could tell by the sound of it that likely something might be affected, but had no idea how extensive the final end effects were going to be.

Home network ethernet cables close by runs of audio and USB cables and because it was all close to the ham PC onboard USB hub and network cabling the one hit was able to be induced into so many places because of so many interconnections.

It was not apparent immediately that there was widespread damage to so many components but it did demonstrate how it's effects can be transmitted/induced in so many directions at once and being like a major static discharge any module with any CMOS components at all can be damaged and not show up for a long time.

I had worked in electronics and communications facilities for 35 yrs and never seen such widespread damage as this anywhere. Usually it was just replacing carbon protector blocks or heat coils in landline termination points and reboot a system to be back in business; no such luck in this case.

When I had the SAT TV dish and receiver installed the Bell service tech did not install a ground; I had to fight with Bell engineering management to get them to install one and even then they only put in a 40' run of #16 guage insulated hookup wire as a ground when it should have been in my opinion #6 bare copper stranded ground cable. But then who am I right?

Lightning is very weird, expensive and not a ham's friend at all.

On 2020-02-25 4:58 a.m., Raj vu2zap wrote:
Seriously, did you have a thunderstorm ?

At 25-02-20, you wrote:
Yes I was wondering about something like a lightning hit blowing the surge protector built into the switch so went to check and discovered the radio doesn't even turn on now so tomorrow likely I will have to replace a fuse in the external power supply; just hope the rig wasn't damaged. GRRRRRR I was just getting close enough to try a QSO or two.


On 2020-02-25 1:22 a.m., Raj vu2zap wrote:
Andy,

Remove the jumper cable between the coax switch and the rig and check for a short.
Happened to me..

Raj

At 25-02-20, you wrote:
The rig goes through a coax switch which I can select a 40 M Hamstick whip, a 20 M small loop antenna, and/or 100 W 50 Ohm dummy load. Doesn't matter which ant is selected same situation so it would seem voltage difference would be the most likely place to start.

Power supply is plugged into UPS but antenna grounds are all direct to a dedicated ground rod for radio gear alone. So might be a potential difference between radio ground rod and electrical utility ground rods.

Thanks for the tip Raj

On 2020-02-24 10:50 p.m., Raj vu2zap wrote:
Andy,

I suspect that your antenna cable is shorted or there is a voltage difference between
your ground and your power supply -ve

When partially plugged in the system behaves like a long wire.

See if your antenna is working with another radio.

Raj

At 25-02-20, you wrote:
I finished setting up the rig and moved it into the shack to put it on full blown antenna expecting some better signals that the minor few available from the temp mag mount HF vert on metal deep freeze lid conterpoise.

When center conductor is inserted 60-80 % inserted signals are evident and AM broadcast stations within 100 mi are easily received and BFO calibration can be adjusted properly. But as soon as the connector is fully inserted in antenna and ground braid makes solid connection signals disappear on all bands and there seems to be a flicker in the display. On a couple of occasions the display completely blanks and goes white. Power off reset then restores display but not the signals until coax outer conductor is disconnected. Seems like some sort of ground loop almost connecting through the input????


Any pointers??

Andy VE4PER

Re: new V6 owner with a few basic questions on wiring and software #v6

Reed N
 

Hi Tim,

1. There are diodes, but no fuses.

2. A scrap speaker should be fine

3. Nextion versions won't work with the v6 stock screen. You'll either want to grab Ashhar's latest or my latest code from github. Ashhar made a video about it today: https://groups.io/g/BITX20/message/76435


Reed

Re: Size and type of USB program cable

Jack, W8TEE
 

Go to your favorite internet search engine, type in "USB connector types", then select "Images" from below the search bar and look for the one that matches you connector. I don't have a V6 (yet), but you should see one that matches. (I think it is Type B).

Jack, W8TEE

On Tuesday, February 25, 2020, 12:08:08 PM EST, Ralph King via Groups.Io <r.rking41@...> wrote:


Just got my BITX V6 today.  Put it together and it works just fine. I have one question.
On the USB program cable that plugs into the back, what size and type plug do I need ? 
I looked in my drawer of cables, and all of the plugs that I have are too small to fit.

Thanks in advance

Ralph  K1KOB  r.rking41@... 

--
Jack, W8TEE

Re: Small change, huge thanks to Ashhar

Reed N
 

I agree that it's a good way to be, but it's been "fixed" for a while now. According to the git history, the ino/cpp change was done back in Dec 17, 2019.

He also mentioned the change to you specifically back in January: https://groups.io/g/BITX20/message/75176


Reed

Size and type of USB program cable

Ralph King
 

Just got my BITX V6 today.  Put it together and it works just fine. I have one question.
On the USB program cable that plugs into the back, what size and type plug do I need ? 
I looked in my drawer of cables, and all of the plugs that I have are too small to fit.

Thanks in advance

Ralph  K1KOB  r.rking41@... 

Re: Small change, huge thanks to Ashhar

Jack, W8TEE
 

All:

If you are an early adopter of the V6 µBITX code, you may want to get the new download, too. Ashhar went through the trouble to upgrade the new version of the software to convert all of the old *.ino files to *.cpp files. This may not seem like a big deal, but it is! There are several benefits to the change.

First, while there has always been multiple source code files in his project, now only one file ends in *.ino. This means two things: 1) the project's ino file is the "primary file" in that it contains both setup() and loop(), the program's main entry point, and 2) the project's directory MUST be the same as the primary file name. That is, if the ino file is ubitx_v6.3_code.ino, the directory for the project must be ubitx_v6.3_code.

Second, the huge win is for those who like playing around with the code, since this new file-naming convention allows the IDE compiler to perform incremental compiles. For example, when I was compiling the 19-file, 11,000+ lines of code in the JackAl project, the first compile in the morning would take a little over a minute on a pretty fast computer (i.e., 3.8Mhz, 8-core with 32Gb of memory). The first compile clears the "dirty flag" in the IDE for each of the source files. Next I would start editing the nettlesome file that is giving me problems and re-compile the project. However, since I only worked on one source code file, only that file has its dirty flag set, so it is the only file that gets recompiled. The linker then merges this newly compiled file with the previously-compiled intermediate files to form the executable for upload to the Nano (or whatever chip). For me, this drops the recompile time from over a minute to less than 10 seconds. If I can save 50 seconds on each compile and a typical day produces 40 recompiles, that saves me over 30 minutes of thumb-twiddling each day! Do that for 19 months, and it's almost enough time for a two-week vacation!

This seemingly-small change by Ashhar simply adds yet another element to the µBITX for which we need to thank him.

Jack, W8TEE

On Tuesday, February 25, 2020, 7:45:15 AM EST, Mick <mgsebele@...> wrote:


Thanks Ashhar!
excellent videos they will really help us newbies.
73
Mick VA3EPM 

--
Jack, W8TEE

Re: V5 not receiving local am stations

Maurice Bersan <Vk6hly@...>
 


Dean, I tried your demo but no luck. Still won't tune down that far.
I will have a look around memory manager next chance I get.
Thanks
Maurice

Re: V5 not receiving local am stations

Evan Hand
 

Dean,

Forgot about the direct frequency input on the CEC/Nextion.  Much easier than all that dial turning.  Only issue is it is not available for the stock 2 line display version of the software.

Thank-you for pointing the shortcut out!

73
Evan
AC9TU

Re: V5 not receiving local am stations

Dean Souleles
 

Hi Maurice,

I can't help you without more information.  What specifically is not working?

The video shows that it can work and does for me, V5, CEC 1.2 firmware and Nextion display.  I believe there may be a setting in uBitx memory manager to allow tuning outside the ham bands, but I don't have time to research it this morning.

73,
Dean
KK4DAS