Date   

RE Smoke test prep more

mtngentleman@...
 

when I remove both  the 2, 2 conductor plugs (supply points) no short. So gues it is something downstream?

S


Re: uBITX + Teensy audio interface - ground loops (?), RX/TX audio bleed? #teensy #ubitx

Martin Potter <ve3oat@...>
 

In general transformers are used to isolate one circuit from another, as well as to transform the impedance, etc etc. So it is quite possible, and sometimes desirable, to have different ground circuits on each side of the transformer. You could try rearranging your ground connections to take advantage of the isolation provided by the transformer.
Very 73,
... Martin VE3OAT


Smoke test prep

mtngentleman@...
 

I've checked and rechecked and my my Bitz 40 shows a direct short across the power connector.  Any clues?

Also notice instructions don't mention hook up of master switch and fuse??

Tks Shep


Re: Redy for smoke test but Bitx 42

mtngentleman@...
 

many thanks!


Re: How to delete a bad .tft file from display

KN4SMO <dtb2greenville@...>
 

"Bet you write the file using a Mac. Macs writes extra files to the sd card.  Believe it has a “.” Prefix but  has the “.tft”  suffix. That is what is causing the multiple tft file error."

OK Fellas, My Mac could properly format my SD card but wrote extra files to the card.  My PC could not properly format my card but could load the single .tft file. The little Nextion tells you the issues when I would try to load a file , smart little thing. With your help I was able to load the proper screen size on the Nextion. This gives me hope I can build the radio.  

Thanks so much for the direction for this issue! 

Scott, KN4SMO


Re: How to delete a bad .tft file from display

MVS Sarma
 

Lo l, I am no expert. I use win7. Yes mac is popular. . Is it possible to rename file extention of unwanted file to serve your cause


On Sat, 5 Oct 2019, 9:43 am Mark Hatch, <mark2382@...> wrote:
Bet you write the file using a Mac. Macs writes extra files to the sd card.  Believe it has a “.” Prefix but  has the “.tft”  suffix. That is what is causing the multiple tft file error. 

Been there...

mark


Re: Redy for smoke test but Bitx 42

Dexter N Muir
 

Wrong, Curt.  Presence of that Tuning connector defines your board as BITX40 - and yes, Shep, that extra 3-pin connector on board was for the potentiometer to control the voltage of a varicap diode in the early analog oscillator. If you have the Raduino, that is redundant: the Raduino replaces that oscillator. The inductor for that oscillator was a toroid: there should be a blank component outline in that area for that(L4), and C91. Refer to the circuit diagram at http://www.hfsignals.com/index.php/2017/11/23/bitx40-circuit-description/

That 4.7k resistor is only needed for proper operation of the uBITX.


Re: cw when I tune #ubitx-help

MVS Sarma
 


On Sat, 5 Oct 2019, 9:45 am Mvs Sarma, <mvssarma@...> wrote:
Econd phto is here. The resistor faced other sude. Hence you see white background.
You can silder normal 1/4w resistor across those leads.

On Sat, 5 Oct 2019, 9:37 am MVS Sarma via Groups.Io, <mvssarma=gmail.com@groups.io> wrote:
You can see the 8 pin connector marked"P1"
Place resistor between pins 2 and 3 as counted from end of 16pin lcd connector. I placed smd 0805  , that too at a vertical angle. Let me show it. 

Obviously 2nd pin goes to ket socket ,  other wire being Gnd.  The battery wire at pin3 need not go up to key socket.

All the best.

On Sat, 5 Oct 2019, 8:13 am KG5YUO, <wtxrcdog@...> wrote:
Hello 
I just got my U-bitx together. I used the Amateur radio kits case kit. I had trouble with my encoder wiring so I cut the wires off of the plugs that came with the kit and soldered them directly to the encoder. This took out the resister that keeps the transmitter from keying cw. Where in the line do I put the resister?

 Thanks for the help 
Bruce KG5YUO
--
"A positive attitude may not solve all your problems, but it will annoy enough people to make it worth the effort."


Re: cw when I tune #ubitx-help

MVS Sarma
 

Econd phto is here. The resistor faced other sude. Hence you see white background.
You can silder normal 1/4w resistor across those leads.

On Sat, 5 Oct 2019, 9:37 am MVS Sarma via Groups.Io, <mvssarma=gmail.com@groups.io> wrote:
You can see the 8 pin connector marked"P1"
Place resistor between pins 2 and 3 as counted from end of 16pin lcd connector. I placed smd 0805  , that too at a vertical angle. Let me show it. 

Obviously 2nd pin goes to ket socket ,  other wire being Gnd.  The battery wire at pin3 need not go up to key socket.

All the best.

On Sat, 5 Oct 2019, 8:13 am KG5YUO, <wtxrcdog@...> wrote:
Hello 
I just got my U-bitx together. I used the Amateur radio kits case kit. I had trouble with my encoder wiring so I cut the wires off of the plugs that came with the kit and soldered them directly to the encoder. This took out the resister that keeps the transmitter from keying cw. Where in the line do I put the resister?

 Thanks for the help 
Bruce KG5YUO
--
"A positive attitude may not solve all your problems, but it will annoy enough people to make it worth the effort."


Re: How to delete a bad .tft file from display

Mark Hatch
 

Bet you write the file using a Mac. Macs writes extra files to the sd card.  Believe it has a “.” Prefix but  has the “.tft”  suffix. That is what is causing the multiple tft file error. 

Been there...

mark


Re: cw when I tune #ubitx-help

MVS Sarma
 

You can see the 8 pin connector marked"P1"
Place resistor between pins 2 and 3 as counted from end of 16pin lcd connector. I placed smd 0805  , that too at a vertical angle. Let me show it. 

Obviously 2nd pin goes to ket socket ,  other wire being Gnd.  The battery wire at pin3 need not go up to key socket.

All the best.

On Sat, 5 Oct 2019, 8:13 am KG5YUO, <wtxrcdog@...> wrote:
Hello 
I just got my U-bitx together. I used the Amateur radio kits case kit. I had trouble with my encoder wiring so I cut the wires off of the plugs that came with the kit and soldered them directly to the encoder. This took out the resister that keeps the transmitter from keying cw. Where in the line do I put the resister?

 Thanks for the help 
Bruce KG5YUO
--
"A positive attitude may not solve all your problems, but it will annoy enough people to make it worth the effort."


Re: How to delete a bad .tft file from display

MVS Sarma
 

On the sd card that loads tft there should only be one file. Nothing else. 
Transfer all other chunk into a folder on your laptop for use later.

Perhaps that is what the message meant.  Kd8cec also mentioned this aspect.



On Sat, 5 Oct 2019, 1:31 am KN4SMO via Groups.Io, <dtb2greenville=ymail.com@groups.io> wrote:
When I try to update the proper file, the display reads, "The system detects multiple tft files, files can not be upgraded. Please remove extra ftf file. 


Re: Unbuilt uBITX Ver4 and Blue Cabinet for sale.

Rob French (KC4UPR)
 

Dumb question on the G4HUP buffer install... since this is attached into the receive side of the bidi amplifier, am I correct in understanding that this will not be adversely affected during transmit?  (And I see also that it is only powered on during receive, but I just want to make sure...)


cw when I tune #ubitx-help

KG5YUO
 

Hello 
I just got my U-bitx together. I used the Amateur radio kits case kit. I had trouble with my encoder wiring so I cut the wires off of the plugs that came with the kit and soldered them directly to the encoder. This took out the resister that keeps the transmitter from keying cw. Where in the line do I put the resister?

 Thanks for the help 
Bruce KG5YUO
--
"A positive attitude may not solve all your problems, but it will annoy enough people to make it worth the effort."


Peanut Power Sprint - SUNDAY - 6PM to 7:59PM EDT

Jim Stafford W4QO
 

Use your BITX!

Come and have some fun, this Sunday!  An easy one from North GA QRP CLUB!

Check 2 things:
1. The RULES on the Sprint page: hhttp://www.nogaqrp.org/PeanutPower/rules.pdf   
CW/SSB/DIGITAL .......  QRP or HIGH power - 80/40/20

2. Check to see if you already have a number:
https://www.dropbox.com/s/qoqkq4sa6tq4jrg/PPS%20Numbers%20by%20Call%202019.xlsx?dl=0

If not, send kj4ym@... an email to request a number!  There are now over 300!

Simple, see you on Sunday.  And visit the nogaqrp.org club webpage.
-- 
Jim Stafford W4QO Roswell, GA USA
QRP ARCI  #6515  www.qrparci.org
NoGaQRP - Peanut #1 -  www.nogaqrp.org
  


Re: How to delete a bad .tft file from display

Jack, W8TEE
 

...if they share the same file name.

Jack, W8TEE

On Friday, October 4, 2019, 3:55:59 PM EDT, MVS Sarma <mvssarma@...> wrote:


No need to delete. Loading a new file removes older one, if i am  not wrong.


On Sat, 5 Oct 2019, 12:55 am KN4SMO via Groups.Io, <dtb2greenville=ymail.com@groups.io> wrote:
Hello,

I have the wrong file loaded in my Nextion.  How do I delete the bad file?   The does not give me a option to delete a file when I try to upload the proper file.

Thanks Scott

--
Jack, W8TEE


Re: How to delete a bad .tft file from display

Jack, W8TEE
 

Usually this message indicates that you have two libraries that share the same name. This is especially likely when you have the same libraries, but for different processors (e.g., an Arduino Nano and perhaps a Teensy or STM32). The angle brackets ('<' , '>') tell the compiler to look in the default libraries directory for the library file. If you are compiling with an Arduino (e.g., a Nano), it looks in the libraries subdirectory off the root directory. So, if my IDE is installed on C:/Arduino1.8.10, it will look in C:/Arduino1.8.10\libraries. However, if you are using angle brackets but compiling a Teensy program, it will look in C:/Arduino1.8.10\hardware\Teensy\avr\libraries. Both of these path names are the "default" for the processor in use. If the include file name is surrounded by double quote marks, the compiler looks in the current project directory first. If it doesn't find the library there, then it looks in its default path.

I'm not sure of this, but suppose you are compiling for a Teensy. It seems to me that if you are compiling within the IDE, but on a "patched" processor (e.g., Teensy, STM32, or ESP32), the angle brackets do this search sequence:

    default path first                             (e.g., C:/Arduino1.9.10/hardware/Teensy/avr/libraries for a Teensy board)
    default "normal" path second        (e.g.,  C:/Arduino1.9.10/libraries)

If you use the Teensy, but use quotes on the include file name is does:

    project path first                             (e.g., C:/myProject)
    default path second                       (e.g., C:/Arduino1.9.10/hardware/Teensy/avr/libraries for a Teensy board)
    default "normal" path third             (e.g., C:/Arduino1.9.10/libraries)

The duplicate file could be on one of these paths. Try renaming the offending file name in the "lowest" (last) path in the compiler's search list.


Jack, W8TEE

On Friday, October 4, 2019, 4:01:56 PM EDT, KN4SMO via Groups.Io <dtb2greenville@...> wrote:


When I try to update the proper file, the display reads, "The system detects multiple tft files, files can not be upgraded. Please remove extra ftf file. 

--
Jack, W8TEE


Re: How to delete a bad .tft file from display

V Zecchinelli <n1vin@...>
 

Try removing the SD card then put in PC and delete bad TFT file.

On 10/4/2019 4:01 PM, KN4SMO via Groups.Io wrote:

When I try to update the proper file, the display reads, "The system detects multiple tft files, files can not be upgraded. Please remove extra ftf file. 


Re: How to delete a bad .tft file from display

KN4SMO <dtb2greenville@...>
 

When I try to update the proper file, the display reads, "The system detects multiple tft files, files can not be upgraded. Please remove extra ftf file. 


Re: How to delete a bad .tft file from display

MVS Sarma
 

No need to delete. Loading a new file removes older one, if i am  not wrong.


On Sat, 5 Oct 2019, 12:55 am KN4SMO via Groups.Io, <dtb2greenville=ymail.com@groups.io> wrote:
Hello,

I have the wrong file loaded in my Nextion.  How do I delete the bad file?   The does not give me a option to delete a file when I try to upload the proper file.

Thanks Scott