Date   
Re: New wiring diagram version

Adrien F4IJA <adrien.grelet@...>
 

Thank you Mark, so good to have a HD version !

Here is the link for you guys if you can't find it on the wiki : https://groups.io/g/BITX20/wikiimage/5204

Re: Ubitx V5 board and holes sizes

Adrien F4IJA <adrien.grelet@...>
 

Thank you for your answer. In fact I'm on my drawing and I've checked with Gary's measurements and it seems to be OK, +/- 0.2mm, which are very fine to me.

Thank you all for your answers, I can go forward on my design !

BTW it's this post for the build : https://groups.io/g/BITX20/topic/33030891?p=Created,,,20,1,0,0::recentpostdate%2Fsticky,,,20,2,0,33030891

Re: Ubitx V5 board and holes sizes

Christopher Ryan <TACTICAL.RADIO.GEAR@...>
 

The dimensions above in the mechanical drawing. Adrien.
Christopher


On Mon, Sep 2, 2019 at 11:00 AM Adrien F4IJA <adrien.grelet@...> wrote:
Christopher : you are speaking about my dimensions or Gary's? 

Re: Ubitx V5 board and holes sizes

Adrien F4IJA <adrien.grelet@...>
 

Christopher : you are speaking about my dimensions or Gary's? 

Re: Ubitx V5 board and holes sizes

Christopher Ryan <TACTICAL.RADIO.GEAR@...>
 

I just measured my board, and your dimensions are right on. Attached is a case that I designed for my V5 board.
73's
Christopher


On Mon, Sep 2, 2019 at 9:00 AM Adrien F4IJA <adrien.grelet@...> wrote:
Thank you both of you for the answers. I'll adapt my plan accordingly to those dimensions. 

After that my plans will be available for everyone who need them. 

Re: Ubitx V5 board and holes sizes

Adrien F4IJA <adrien.grelet@...>
 

Thank you both of you for the answers. I'll adapt my plan accordingly to those dimensions. 

After that my plans will be available for everyone who need them. 

Builder for Disabled

Thom LaCosta
 

Are there any folks who build fir or willing to build for a disabled ham?  I have tremor which makes wielding a soldering tool and envornmental hazard.

thanks
thom k3hrn

Re: Ubitx V5 board and holes sizes

Evan Hand
 

I have both v4 and v5 boards, and have swapped them between cases.  Holes do line up.

FWIW
73
Evan
AC9TU

Re: Ubitx V5 board and holes sizes

Gary Anderson
 

Adrien,
My understanding is that V3,4 and 5 boards are the same size and same mounting hole spacing.  Done as such so they are interchangeable in the case.

My V3 board is 5.5" (with 5.1" center line hole spacing) x 6.0" (with 5.6" center line hole spacing)

Accurately,  mine measures 5.508" x 6.007".  I would expect variation in the thousandths of inch.
I can't accurately measure hole spacing to center line, I have to eyeball that the tips of the vernier caliper are in the hole center.
But, it seems to fit very well to an inch based standard.  (which would be 129.54 mm x 142.24 mm hole center line spacing converting to metric)
The hole center line spacing on the drawing you posted don't make much sense to me since it doesn't align to either an inch or metric standard.
Yes, the mounting screws should be smaller than the hole diameter for build tolerance. But best to start with the correct target (which is what you are asking)

Rgds,
Gary

Re: i2c signal meter/analyser/dsp/cw decoder

Werner de Vos
 

Hi Sourav, did you already managed to get it working in full screen? Having the same 'problem' here. 
73 Werner pa3gyv

Ubitx V5 board and holes sizes

Adrien F4IJA <adrien.grelet@...>
 

Hi there,

I'm waiting for my board to arrive but I'm already on the design of the case and everything else.

I'd like to take a chance an prepare the box before the board will be there so I ask your support if possible.

I've found on GrabCad a cad file of the ubitx board, and here are the sizes I have :


Could a nice owner of a V5 board could confirm those measurements to be sure they are accurate ?

Thank you a lot !

73's
Adrien F4IJA

Re: Using the Arduino with other QRP radios

Gordon Gibby <ggibby@...>
 

I have used it as the Computer controllable VFO for a Heathkit SB – 100 vacuum tube radio and it worked well.




On Sep 2, 2019, at 05:06, Dennis Yancey <Kd4epg@...> wrote:

did you use the output and ground to replace the crystal?or was other action necessary?

--
72 and God bless
KD4EPG

Re: Using the Arduino with other QRP radios

Dennis Yancey
 

did you use the output and ground to replace the crystal?or was other action necessary?

--
72 and God bless
KD4EPG

Using the Raduino with other QRP radios

Dennis Yancey
 

I was wondering if anyone has tried using the Raduino as a VFO to replace the crystal on some other QRP radios to replace the crystal like the Rockmite II, the 49er and other small minimal power QRP rigs?

Any ideas? Think the Raduino output will need a small buffer amp? Love to hear your thoughts.
--
72 and God bless
KD4EPG

Re: Using the Arduino with other QRP radios

Ashhar Farhan
 

I have used  Raduinos as a general purpose VFO on many radios. It works quite well.

- f

On Mon, Sep 2, 2019 at 1:37 PM Dennis Yancey <Kd4epg@...> wrote:
I was wondering if anyone has tried using the Arduino as a VFO to replace the crystal on some other QRP radios to replace the crystal like the Rockmite II, the 49er and other small minimal power QRP rigs?

Any ideas? Think the Arduino output will need a small buffer amp? Love to hear your thoughts.
--
72 and God bless
KD4EPG

Re: Nextion Diisplay Fonts

Mark Hatch
 

I assumed you have tried adding a new font (of your choice) to the nextion editor and using it?

73
mark

Re: Nextion 3.5 current draw?

MVS Sarma
 

You can even try 4 line display ith kd8cec firmware.


On Mon, 2 Sep 2019, 6:01 am Tech Guy, <tech48055@...> wrote:
I was reading an ad for the nextion 3.5 display that mentions current draw up to 500 ma. Is that actually the draw for the display? I may be sticking to the stock display.

Re: Nextion 3.5 current draw?

Evan Hand
 

Here is the link to the 3.5"
https://www.itead.cc/wiki/NX4832K035

As you can see the normal current draw is 145 ma

The 3.2" display is not that much smaller and draws 85 ma. :
https://www.itead.cc/wiki/NX4024K032

I would not give up the functionality unless you were really looking for ultimate portability.

FWIW
Evan
AC9TU

Re: high pitched wine on 80 and 40 M

jfein2000@...
 

May well be.  The audio is too low for the speaker to be of any use.  I recently was able to pick K6MYC from CA who usually comes booming in at 10 or 20 over S9, using headphones.  I will be using powered speakers with it and that should help somewhat.  However I suspect it could be more sensitive....just doesn't feel like it is solely an audio issue.  Given there is iimited alignment functionality not sure how to progress that.  Also very hard to find a decent USB signal in Australia atm with propagation so poor.  It has been awful here for the last week. Cheers Jeff VK3GMO
 

 

 

Re: Nextion 3.5 current draw?

Jim Sheldon
 

Yes, that's actually the current draw for the nextion.  Also, the larger the Nextion, the more current it draws.  That's pretty much the same for all the color touch screen displays, even those that are non Nextion.  

TSW, in choosing our color touch screen displays for the BITeensio card (much faster than a Raduino with the NANO processor) and it uses the 2.8" or 3.2" ILI9341 based color touch screens.  We also can use the RA8875 based 5" displays, but there the current draw at 3.2V is around 750 mA and if you don't use lots of cooling air on the separate 3.2" regulator's big heat sink, it won't last very long so the largest display we fully support is the ILI9341 in 3.2" size.  It draws about 140 milliamps with the backlight on full and is still well within the capability of the onboard 3.2V regulator of the Teensy 3.6 MPU.  The nice thing about the 2.8 and 3.2" ILI9341 displays and our BITeensio card is that you can use either display interchangeably without changing software.  Depending on which of the displays you have, you might have to change cables to switch from the 2.8 to 3.2" displays though there are several out there that use the exact same connector on both the 2.8 and 3.2 versions.

The BITeensio can also handle both V4 and V5 uBITX radios with a menu selected change and calibration data is saved for each so if you should need to switch it between the two types, all you need do is touch up the calibration at the time you change.  No separate memory manager OR computer connection is required other than for reprogramming the Teensy 3.6 when needed or if you want to use CAT control.

See the Triumvirate Skonk Worx (TSW) website, www.w0eb.com/Page2.html for details on the BITeensio board kits.  (We don't supply the Teensy 3.6 or the display - that's up to the kit builder to decide).  There are other items on the TSW pages of interest to uBITX radio owners as well.

Jim, W0EB
TSW Project Coordinator

------ Original Message ------
From: "Tech Guy" <tech48055@...>
Sent: 9/1/2019 7:31:12 PM
Subject: [BITX20] Nextion 3.5 current draw?

I was reading an ad for the nextion 3.5 display that mentions current draw up to 500 ma. Is that actually the draw for the display? I may be sticking to the stock display.