Date   

Re: i2c encoders in matrix with I/O #ubitx

John (vk2eta)
 

Interesting devices. The boards also have 2 or 3 general I/O pins (depending on the usage of the LED), and 128 (256?) Bytes of EEPROM.

From a quick read of the Arduino library (https://github.com/Fattoresaimon/I2CEncoderV2.1) they have mapped registers at the selected I2C bus address (one for each encoder module). The registers perform configuration and access to encoder, push-button and GPIO pins and EEPROM data.

The library supports interrupts and callbacks which is handy but requires one interrupt enabled digital input pin (but I am not sure if it's one per module or if the modules can be daisy-chained to the one input).

73, John (VK2ETA)


Re: Project : Ubitx go box with batteries (topic will be updated upon works done)

Adrien F4IJA <adrien.grelet@...>
 

Salut Olivier,

Thank you for those informations (frenchies talking to each other in english, is kinda fun !)

So, that's quite interesting the running time you have. With that information, I think I should go for example with 3S2P to have extended autonomy, but 3S4P seems to be really overkill, even if you plan to go for 1 week SOTA without recharging, which will ne be my case (just one day session most, maximum a WE with other activities than radio too).

Another question : what do you think about the Nextion LCD ? In fact I'm thinking beetween two things :

My point is what are the benefits of the Nextion LCD, beside the comfort of use and ergonomy of menus. Also it's fancy and cool with that display ! Does it have other things you can't do with the basic LCD ?


Re: Project : Ubitx go box with batteries (topic will be updated upon works done)

 

Bonjour Adrien.
The 3 X 18650 Battery pack I've installed in my V5 give me height hours running time at 10% transmitting time (on dummy load), I installed the same battery protection board as yours and I plan to modify the charging circuit. the mods are :
2 separates 12V rails, 2 X 5V rail (one for TX, one for RX)
Nextion 2.8" touch screen feeded by the Raduino
VK3YE's AGC (12V RX)
XPT8871 AF amp with tone control (5V RX rail)
SSM2167 mike compressor (5V TX rail)
with these adds the power consumption is not very different (not verified).
I plan to re-install a second arduino (standalone analyser) with it's own 5V rail.
I will check the real consumption datas and write a complete report.
Bonne journée !
Olivier

Le mar. 27 août 2019 à 10:18, <adrien.grelet@...> a écrit :
I've made some spreadsheet work upon the battery size.

It appears, with 15W global power drained from the setup when transmitting, that a 3S2P should be enough and smaller to fit in the box (and also lighter).

Here is the screenshot :



So, more than 4 hours just on transmit is not bad at all !
If anybody have already measured the real power drain if the ubitx when transmitting (not the output power, the power used on the power supply).
Thx


Re: Project : Ubitx go box with batteries (topic will be updated upon works done)

Adrien F4IJA <adrien.grelet@...>
 

Yes, keep tuned Jeff ! I'll receive all the parts in a month or so, but I've the time to design well everything to avoid losing time on the build.

Also, all the designs are made with SpaceClaim, that I use everyday in my company.

At the end of the project, I'll be able to put in the folder the STEP file of the design so that everyone should be able to process it.


Re: Reduced power on 40 meters. #ubitx #v5

Viktors Miske
 


Re: Project : Ubitx go box with batteries (topic will be updated upon works done)

Jeffrey Benedict
 

Nice use of the design tools!  Keep the group apprised of your progress.

I'm looking to put together something that looks kind of like one of those WWII spy radios.  The Ubitx is about the right size to fit in the size of one of those radios but will be so much more capable!  Definitely planning on having a battery on board and room for microphone, earphones and key. Not sure if I will have a speaker.  An HT speaker mic would do the job of both and, maybe, work as a key, too, like is possible with an 817. I'm not much of a CW guy so that might be fine. So many possibilities!

73

Jeff
--
Jeff, K7AIL  CN87

raoul@...


Re: Reduced power on 40 meters. #ubitx #v5

Murray Wills (ZL2IQ)
 

Hi

Can you give the URL of those transistor mods Vic. Keen to get a little more output myself. 

73 Murray ZL2IQ


Re: Reduced power on 40 meters. #ubitx #v5

Vic Richardson
 

I received my v5 ubitx yesterday and looked closely at the xmtr on the bench tonight. As it arrived, I was getting 7W on 80m, 5W on 40 and 4.5W on 20,15m and 3W on 10. I did the 2N2222/BTR106 transistor mods, as documented in the uBITx website, and now get 18W on 80, 12W on 40, 7W on 30 meters and 15W on 20 meters. 40 meters is still lower than 20 and the unit draws 2.55ADC on both 80 and 40 meters (the finals get hotter on 40) and only 2.1ADC on 20 meters. I'm not complaining since 12W on 40 meters is a great power (I just wanted to get 10W as claimed) but it points towards some issue in the 40 meter filter. Also, I'm only getting 37 dB suppression of the third harmonic of 40 meters vs >48 dB suppression of the third harmonic on both 80 and 20 meters. Before the transistor change I had 40 dB suppression on 40 meters (still 3 dB out of spec). Attempts at improving the 40 meter filter did not help so I'm guessing there is still a little leakage around the 40 meter filter even on v5 boards and that the transistor mod raised the harmonics some. My plan is to add a relay switched outboard 1-2 stage low pass filter just on 40 meters and drive that relay from the current 40 meter relay in the filter switching. All that aside, this is an impressive design for the price!


Re: CAT control of uBITX

Mark Hatch
 

As far as I can tell, the only neg on the KD8CEC software is that "apparently" it does not read the encoder reliability fast enough to allow you to use a digital cnc 100ppr knob you can get on ebay for $14. There was a thread that "some ubitx firmware" read the encoder fast enough to respond to 100ppr. (check ubitx.net for a discussion on encoder).

however, for the standard encoder that comes with the ubitx kit, KD8CEC reads it fine and you will be happy.

The other thing to do the upgrader sooner than later is that on first install, KD8CEC records the criitical values (OSC, BFO, etc). You then have the ability to do a "factory reset" to these values if in the future you ever mess something up. So do the upgrade before you start "tuning"...

73
Mark
AJ6Cu


Re: CAT control of uBITX

John Seboldt K0JD
 

OK, looks like I have all the info I need, just set a time and take the courage to do it! Thanks

On 8/27/2019 17:30, Doug W wrote:
On Tue, Aug 27, 2019 at 05:13 PM, John Seboldt K0JD wrote:
So I take it that you use his uBITX Manager to actually load the stuff? It seems that we have to deduce the step by step instructions.
John,
On the same site KD8CEC has step by step instructions.  http://www.hamskey.com/2018/01/how-to-upgrade-ubitx-firmware.html  That is written for an older version of his firmware.  Make sure you download the latest.
 
--
www.bitxmap.com


Re: high pitched wine on 80 and 40 M

John (vk2eta)
 

Hi Jeff,

Here is the link to the thread.

https://groups.io/g/BITX20/topic/8872690#54576

In summary it was the nano's crystal frequency. 

I changed the nano and it solved the issue.

To see if it's related to this issue just touch the nano's crystal or change slightly the BFO's calibration and the tone will change too.

If it doesn't, it's another issue.

Hope that helps.

Cheers, John


Re: ssm2167 board for compression #ubitx #ssm2167

John (vk2eta)
 

Hi Brad,

Thanks for the information. 
I should be able to give It a go in a week or so and I'll report on the results. 

Even at the high rate of compression/limiting where mine is at present I get reports of "audible compression, but not unpleasant".

But I would like to soften it a little and have the noise gate work properly.

Thanks and 73, John


Re: high pitched wine on 80 and 40 M

jfein2000@...
 

Thanks John,  it is rev 4, 2018 vintage.  It receives on 80 and 40 but the whine in the background is very irritating.  Tried to find any relevant posts by you as noted but without success.  I suspect it is SSB related. 

cheers

jeff

 

 

 


Re: i2c encoders in matrix with I/O #ubitx

Tom, wb6b
 

It looked like they mapped 256 I2C address to the various internal registers and the EEPROM. Then had an additional 7 bits of high order I2C addresses. There is an expanded I2C addressing scheme, greater than 7 bits, but I do not know how many libraries support it.

If what they actually did is create a bunch of pseudo registers, then you will need to deal with creating a protocol on top of the I2C protocol. Hope they provide drivers to layer on the pseudo register addressing and handshake, over the I2C protocol, if that is the case.

Tom, wb6b


Re: ssm2167 board for compression #ubitx #ssm2167

n8yg
 

Hi John, 
I understand completely. 
The value of pot I chose was 50k, and the adjustment point relative to ground is about 10K.. so 1/5 the voltage output of the microphone. Of course this adjustment is after the cap on the board so that I did not adjust the electret bias as well.. but I think you got that.  I found it difficult to solder to the pads without destroying them, but succeeded finally. I started laying out a board with these mods... but who knows if I'll ever get it done. :-) 

I will caution that I discovered that the noise gate and compression.. seem to have an interaction.. but the noise gate certainly works.. and as my good friend says about the compression now.. "Wow Brad that sounds as good if not better than your 100 W rig at 100 Watts"
BTW thanks for your inspiration for using this chip. It really makes the difference for sure. 
I read your notes.. but was frustrated with the compression making little difference between full compression and none.. Now.. there is a huge difference. 
I hope this helps... I have been hoping someone else would give it a try. 

73,
Brad N8YG


Re: i2c encoders in matrix with I/O #ubitx

John Scherer
 

From what I can tell, each board is an i2c slave and utilizes a single i2c address. However, each board is configurable to use one of 127 possible i2c addresses.  I would assume each board would need a separate i2c address, and with 127 available, I don't think this would be a problem.  Or am I missing something?
--
John - N0CTL - Fulltime RV in a 40' motorhome


Re: i2c encoders in matrix with I/O #ubitx

Tom, wb6b
 

On Tue, Aug 27, 2019 at 01:59 PM, John Scherer wrote:
I came across an interesting, i2c addressable rotary encoder board
Very clever deign. Also did not know encoders with an RGB LED that could send light down a clear shaft to the knob were available. 

These boards seem to use a lot of I2C addresses, but they claim they are compatible with most or all development boards.

Tom, wb6b


Re: CAT control of uBITX

Doug W
 

On Tue, Aug 27, 2019 at 05:13 PM, John Seboldt K0JD wrote:
So I take it that you use his uBITX Manager to actually load the stuff? It seems that we have to deduce the step by step instructions.
John,
On the same site KD8CEC has step by step instructions.  http://www.hamskey.com/2018/01/how-to-upgrade-ubitx-firmware.html  That is written for an older version of his firmware.  Make sure you download the latest.
 
--
www.bitxmap.com


Re: CAT control of uBITX

John Seboldt K0JD
 

So I take it that you use his uBITX Manager to actually load the stuff? It seems that we have to deduce the step by step instructions. Yeah, have also seen the Nextion screens so will think about that too.

John K0JD

On 8/27/2019 16:03, Mark Hatch wrote:
Hi,

KD8CEC's software has CAT control. You can download it via his website: http://www.hamskey.com/2019/04/release-cec-firmware-v1200-for-ubitx.html

Since you have a V3, make sure you download the one for V3.  Match it up with a Nextion screen and you will love the upgrade even more!

73
Mark
AJ6CU


Re: ubitx 5 and boatanchor Collins amp #ubitx #v5 #linear-amp

Dean Souleles
 

Hi Jim,

Gotcha - that makes a lot of sense.  Or if I only want 100-150 watts out I could just use the 2 pill - and leave the Collins for my benchtop station.

Thank you,

Dean
KK4DAS