Date   

Re: CW BFO calibration

Bill Carpenter
 

CW, not CE signals LOL.


Re: Audio chip burn out.

Ian Reeve
 

I do not insert or pull out any Jack plugs whilst the equipment is powered.Experience has shown that there can be a momentary short as the plug is inserted or pulled out especially problematical on audio amplifiers where the outputs may be shorted destroying the audio chip.Ian M0IDR


From: BITX20@groups.io <BITX20@groups.io> on behalf of Mvs Sarma <mvssarma@...>
Sent: Saturday, July 28, 2018 4:03:23 PM
To: BITX20@groups.io
Subject: Re: [BITX20] Audio chip burn out.
 
the message got jumbled up
 here is it again.
you do get pin to pin replacement.
search out for NJM 2073 8 PIN DIP
THIS HAS BEEN DEALT WITH EXTENSIVELY BY EXPERTS.


Regards
MVS Sarma
 

On Sat, Jul 28, 2018 at 8:31 PM, Mvs Sarma <mvssarma@...> wrote:
you do get pin to pin replacement.
search out for NJMBY EXPERTS.
THIS HAS BEEN DEALT WITH EXTENSIVELY 2073 8 PIN DIP.

all the best
regards
sarma
vu3zmv

Regards
MVS Sarma
 

On Sat, Jul 28, 2018 at 8:26 PM, MAX <max@...> wrote:
I was using a shorted plug to plug into the key jack while testing an
antenna tuner.  I accidentally plugged the plug into the headphone jack.
When I realized my mistake and unplugged it there was no receiver audio.  I
assume that U1 is what burned out.  I didn't follow that thread very
closely but I did get that a pin for pin replacement does not exist.   I
don't remember what the solution was but I need it now.  Someone please
fill me in.  Thank you in advance.


Regards.

Max.  K 4 O DS.

I've Never Lost the Wonder.

Email: max@...

Vacuum Tube  Site: http://www.angelfire.com/electronic/funwithtubes/
Transistor site: http://www.angelfire.com/planet/funwithtransistors/
Woodworking site:
http://www.angelfire.com/electronic/funwithtubes/Woodworking/wwindex.html
Music site: http://www.maxsmusicplace.com

To subscribe to the fun with transistors group send an email to.
Funwithtransistors+subscribe@groups.io

To subscribe to the fun with tubes group send an email to,
funwithtubes+subscribe@groups.io

To subscribe to the fun with wood group send a blank email to
funwithwood+subscribe@...o








Re: KD8CEC firmware and basic Manager settings #ubitx-help

Nigel G4ZAL
 

Once you have changed values in Memory Manager, encoded/written them back to your uBitx, you must then disconnect from the USB cable and remove power from the uBitx (turn off).
Then, power on again and after the power cycle, connect Memory Manager again and read in/decode the values - they should have changed now...

Nigel.


Re: IRF510 ubitx failure

ajparent1/KB1GMX <kb1gmx@...>
 

Enclosed is the IRF610 datasheet.

I see no reason to claim its more robust.  It trades a 200V Drain to Source voltage for a 100V of the IRF510 
and the max current is 3.3A against the IRF510 5.6A.

FYI neither are audio transistors though you certainly use them for that.  They are high speed high current switches.
Typical use is when you want to turn on a 3A lamp on or off with very little power to the gate or switching power supply
where switching speed and low on resistance is critical to efficiency.   Its why the make fairly good and inexpensive
RF power amps.

Actually for the typical power dissipated usually around 5W per device in most ubitx running 10 watts out
if the heat sink is allowed good airflow (convection) will be quite adequate.  However many boxes are too
tightly closed to allow adequate airflow.  However if you are concerned a tiny fan and some opening to
let the hot air out can make a significant difference.

The two things that kill them fast is self oscillation due to poor circuit design or layout and the resulting heat.
This is bad as often the power level is well above the TX power and the frequency is likely outside the
range of filters used.    The other is just long transmit sessions without adequate cooling (blocked
air flow or small heatsinks).  

Allison


Accidental Calibrate #ubitx #calibration

Christopher Miller
 

This was my advice 


Re: Audio feedback during transmit? #ubitx

Bruce W4BRU
 

Thanks for that. I had posted "uBitX SSB transmit oscillations on 40m only" but then noticed lesser sound from the speaker on higher frequencies. I do not know the "uBiTX memory manager" but it is time I learn.


Re: uBITX and nulling the carrier #ubitx-help

ajparent1/KB1GMX <kb1gmx@...>
 

Usually carrier at that level may indicate the BFO needs to be set a bit further away.

The uBitx has issues with carrier leakage but usually not that bad, so check the carrier frequency first!

Joel,

While the diodes are well matched the transformer is still handmade though fairly good.
To assure balance a 50 ohm pot at the winding center tap pins 5 and 3 would help.
The RF would be on the wiper and the two wires to the ends.  Mount it under the board
with short leads.

Allison


Re: uBITX and nulling the carrier #ubitx-help

 

Michael,

The short answer is, you don't. The newer released uBitx's dont have a way to null the carrier because theoretically it's not necessary due to the diodes used in the mixers. It's near impossible to find two discrete diodes that are perfectly the same, but the SMD diodes, (I think BAT54SL),  Farhan used are two diodes in a single package that are as near the same characteristics as you can get, so eliminating the need for a null adjustment. Maybe yours are not perfect?

Joel
N6ALT


Re: Accidental Calibrate #ubitx #calibration

Ion Petroianu, VA3NOI
 

You are missing a second, calibrated receiver on which you should be able to listen for zero beat.
Try uploading Ian's firmware ( www.hamskey.com ) and you will do zero beat on your uBitx receiver using the UT beacon you can receive in your area (5, 10, or 15 MHz).
To use Ian's firmware you do not need to do any hardware modifications and you will see lots of improvements.
73,
Ion
VA3NOI

--
Ion

VA3NOI


Re: Accidental Calibrate #ubitx #calibration

m5fra2@...
 

Sorry… thanks Joel!!

 

 

From: BITX20@groups.io <BITX20@groups.io> On Behalf Of Joel Caulkins
Sent: 28 July 2018 17:27
To: BITX20@groups.io
Subject: Re: [BITX20] Accidental Calibrate #ubitx #calibration

 

Frank,

You have inadvertently entered the Calibration Twilight Zone. I did the same thing 4 days ago and I only yesterday was able to escape. Here's what I had to do, first upgrade to KD8CEC's firmware 1.08 or later, then download version 1.04 of KD8CEC's uBitx Memory Manager and install it. Then follow this thread,  https://groups.io/g/BITX20/topic/kd8cec_firmware_and_basic/16637851?p=,,,20,0,0,0::recentpostdate%2Fsticky,,,20,2,0,16637851 and load the defaults mentioned there which will allow you to get control of your uBitx again, then using the memory manager continue to tweak your settings until you get it right on. I know it sounds daunting, but that's what I had to do to get back into the land of the living. As far as I'm concerned, the stock calibration procedure should be removed from the base firmware as it does more harm than good.

Joel
N6ALT


Virus-free. www.avast.com


Re: Long delivery time this time #ubitx

Jerry Gaffke
 

Fine with me.
He's not personally fielding all inquiries from thousands of customers about shipping details.

The email address of those charged with handling such matters is         
    hfsignals at gmail dot com
where you supply the "at" and the "dot".
This forum will swallow attempts at posting a valid email address as a way to thwart the spambots.

Jerry


On Sat, Jul 28, 2018 at 09:09 AM, Christopher Miller wrote:
Farhan replying to the group, better contact hfsignals, priceless. 


Re: Accidental Calibrate #ubitx #calibration

m5fra2@...
 

Thanks Frank, also been there but getting out of it!

 

Colin – M5FRA

 

From: BITX20@groups.io <BITX20@groups.io> On Behalf Of Joel Caulkins
Sent: 28 July 2018 17:27
To: BITX20@groups.io
Subject: Re: [BITX20] Accidental Calibrate #ubitx #calibration

 

Frank,

You have inadvertently entered the Calibration Twilight Zone. I did the same thing 4 days ago and I only yesterday was able to escape. Here's what I had to do, first upgrade to KD8CEC's firmware 1.08 or later, then download version 1.04 of KD8CEC's uBitx Memory Manager and install it. Then follow this thread,  https://groups.io/g/BITX20/topic/kd8cec_firmware_and_basic/16637851?p=,,,20,0,0,0::recentpostdate%2Fsticky,,,20,2,0,16637851 and load the defaults mentioned there which will allow you to get control of your uBitx again, then using the memory manager continue to tweak your settings until you get it right on. I know it sounds daunting, but that's what I had to do to get back into the land of the living. As far as I'm concerned, the stock calibration procedure should be removed from the base firmware as it does more harm than good.

Joel
N6ALT


Virus-free. www.avast.com


The new radio!

m5fra2@...
 

The BITX just gets better! Sorted out some snags but cannot get the Hypermite CW filter to work, will have to remove it from the case and work on it. I uploaded the latest version of the KD9CEC firmware today which is excellent. Now thinking of another BITX for the shack with a Nextion display as this one is for /P.

 

Colin – M5FRA


Virus-free. www.avast.com


Re: Accidental Calibrate #ubitx #calibration

EI_Frank
 

Hi Joel,
Many thanks for sharing your frustration and the eventual solution.
You are a gentleman.
I shall try your solution in the hope of getting out of this Calibration Maze.
I agree with your assessment of the Stock Firmware, Tune-up instructions are not much better and don't agree with the actual firmware on board the uBitx.
This is a great little rig which has great potential, but lots of unnecessary grief in the Tune-Up.
Many thanks again.

73,

Frank 
EI8HIB


On Sat, Jul 28, 2018 at 5:27 PM, Joel Caulkins <caulktel@...> wrote:
Frank,

You have inadvertently entered the Calibration Twilight Zone. I did the same thing 4 days ago and I only yesterday was able to escape. Here's what I had to do, first upgrade to KD8CEC's firmware 1.08 or later, then download version 1.04 of KD8CEC's uBitx Memory Manager and install it. Then follow this thread,  https://groups.io/g/BITX20/topic/kd8cec_firmware_and_basic/16637851?p=,,,20,0,0,0::recentpostdate%2Fsticky,,,20,2,0,16637851 and load the defaults mentioned there which will allow you to get control of your uBitx again, then using the memory manager continue to tweak your settings until you get it right on. I know it sounds daunting, but that's what I had to do to get back into the land of the living. As far as I'm concerned, the stock calibration procedure should be removed from the base firmware as it does more harm than good.

Joel
N6ALT



Re: Accidental Calibrate #ubitx #calibration

 

Frank,

For what it's worth, here is my struggle thread. https://groups.io/g/BITX20/topic/the_dreaded_lsb_and_usb_swap/23816435?p=,,,20,0,0,0::recentpostdate%2Fsticky,,,20,2,20,23816435
Maybe you can glean some more info out of it.

Joel
N6ALT


Re: Accidental Calibrate #ubitx #calibration

 

Frank,

You have inadvertently entered the Calibration Twilight Zone. I did the same thing 4 days ago and I only yesterday was able to escape. Here's what I had to do, first upgrade to KD8CEC's firmware 1.08 or later, then download version 1.04 of KD8CEC's uBitx Memory Manager and install it. Then follow this thread,  https://groups.io/g/BITX20/topic/kd8cec_firmware_and_basic/16637851?p=,,,20,0,0,0::recentpostdate%2Fsticky,,,20,2,0,16637851 and load the defaults mentioned there which will allow you to get control of your uBitx again, then using the memory manager continue to tweak your settings until you get it right on. I know it sounds daunting, but that's what I had to do to get back into the land of the living. As far as I'm concerned, the stock calibration procedure should be removed from the base firmware as it does more harm than good.

Joel
N6ALT


Re: Instruction Manual needs revision #ubitx

EI_Frank
 

Hi Richard, I have the same issue with Align the Master Clock? I am on Ver 4.3. So I am unable to tune up properly.
Did you get this issue resolved ?


Re: NEXTION 4.3" Basic & Enhanced now Supported

matthew cook <cookmatt67@...>
 

Holly batcrap.  They sent me the wrong display and I didn't even check it..  txs for the kick...


On Sat, Jul 28, 2018 at 10:29, Björn Pasteuning
<bjornpd5dj@...> wrote:
Hi Matthew.

That's correct your nx4832k035_011 is a 3.5" display not an 4.3"
--
73' Björn de PD5DJ
www.pd5dj.nl


Re: Long delivery time this time #ubitx

Christopher Miller
 

Farhan replying to the group, better contact hfsignals, priceless. 


Re: Long delivery time this time #ubitx

Christopher Miller
 

lololol


On Sat, Jul 28, 2018, 12:18 AM Ashhar Farhan <farhanbox@...> wrote:
Better write to hfsignals and find out what happened 

On Sat, 28 Jul 2018, 11:17 Kevin Luxford, <kbgluxford@...> wrote:
In the past I have ordered, and have had delivered, several rigs from Farhan, using India Post.  It has generally taken about four weeks from order to delivery in Australia.  However, a Ver 4 uBITX ordered from Paradigm E-Commerce Private Limited on 28 May has not been delivered by today, 28 July.  Maybe the introduction in Australia of GST on imports less than AUD1000 from July 2 this year has held it up.  However, normally goods clear Border Force (Customs) within about 10 business days.  Starting to get a bit anxious that maybe it went astray in the mail.  Next time, I will pay the extra for DHL!
73, Kevin VK3DAP / ZL2DAP