Date   
Re: RF AGC experiments #ubitx

Don, ND6T
 

Thanks for sharing Mike. I found that most of my 2N7002's had about 10 pF output capacitance, the specs show up to 30 pF. Still not bad compared. I found that I got about 23 dB maximum attenuation with the shunt connection. Did you make a quantitive measurement? Hard to tell much from the audio clip but it sounded much like my first circuit (simple shunt). Makes for an easy mod, though! My next step was just to hang another 2N7002 across the output of first IF which added another 15 dB or so. The series element made the big difference, though. 73, Don

Re: No S-Meter nor callsign showing in KD8CEC #ubitx

Sascha Bohnet | DL5SMB
 

I did this of course.
I checked the box in the Ubit Manager on the PC, pressed encode and reuploadet it. Turned the radio off and on again. No change :-/

Re: No S-Meter nor callsign showing in KD8CEC #ubitx

Philip
 

UBITX_CEC_Vxxxxx_16P.hex  : It is the LCD equipped with uBITX. Default LCD, 16x02 Parallel LCD This is the one you need

Sorry I cant help anymore as it works fine for me.

Re: No S-Meter nor callsign showing in KD8CEC #ubitx

Ralph Mowery
 

Did you run the ubitx Memory  Manager program with the new software loaded ?  If so,did you go to the s-meter part of the program and turn  the s-meter on and enter some numbers in the  blocks ? It works fine for me using the original 16x02 display.

On Sun, Jun 17, 2018 at 5:23 PM, Sascha Bohnet via Groups.Io <saschabohnet@...> wrote:
Hello everybody,

I just installed ND6Ts AGC Circuit and wanted to turn on the S-Meter in the firmware according to the instructions on
KD8CECs Homepage.
However I just can't get it on the display.

Whatever I selection of options I choose,  the only things i get on my standard 16x02 Parallel Display is

VFO A, VFO B, Mode, and tuning steps. I can change which VFO is shown first (toggling) or switch on (and off) rotation,
but I am not able to get my callsign or the S-Meter on the display.

The S-Meter signal is there - i checked it in the setup, ADC Pin7 gets read and a reasonable value is shown.

Am i doing something wrong? I thought first I may have accidently uploaded the 16x04 P Firmeware and reuploaded again -
this was not the case.

However according to the pictures (http://www.hamskey.com/2018/05/setting-smeter-to-ubitx-with-cec.html) there must be a way.

Any help would be appreciated.

Sascha, DL5SMB
_.
Your Subscription | Contact Group Owner | Unsubscribe [rmowery42@...]
_._,_._,_


Re: Help with AGC kit wiring

Bill Carpenter
 

Just so I got this, the 3 pin connector replaces the coax connections so the only other connections are the +5 Volts and the twisted pair from the volume control?  Looks like a very elegant solution!  I like being able to mount the board securely.

Thanks!

Re: BITX QSO Afternoon/Evening, Sunday, June 17, 3PM & 7PM Local Time, 7277 kHz in North America, 7177 kHz elsewhere.

John P
 

I'm calling CQ on 7277 but have a S9 noise level here, so not sure I'll hear anything!
--
John - WA2FZW

Re: Raduino needed.

Nick VK4PP
 

I have a spare stock Raduino. Email me....

73 Nick VK4PLN

Re: Help with AGC kit wiring

Don, ND6T
 

You got it! I do recommend the 3 position SPDT on-off-on switch idea, though, for the front panel control. Otherwise, Kees included those shorting plugs for you. You're Welcome! 73, Don

Re: Remote cooling fan indicator #ubitx

Joe
 

This quite common. To eliminate the problem make sure you have a hash filter.
Typically a 1000mfd capacitor or higher with a small resistor ( 2-10 ohm) in series, followed by another similar capacitor .. Basically a pi filter with a series resistor in the middle.

 I use them on my rigs to kill noise, especially fan noise.

Joe
VE1BWV


On Sun, Jun 17, 2018, 5:41 PM Rob Snow <rsnow@...> wrote:
I installed my 12v auxiliary cooling fan in my uBITX earlier today to replace the unseemly box fan I had propped up over my open cased radio.  After I installed it and dialed in the temps I fired up WSJT-X to see if there was any performance changes with the fan on, well, lo and behold I discovered that I have a "remote digital fan on indicator" on all bands so I'm assuming it's getting in via the audio circuit not RF side.  It also turns off when the fan does.  Perfect, I think I'll leave it.

Behold:

Re: BITX QSO Afternoon/Evening, Sunday, June 17, 3PM & 7PM Local Time, 7277 kHz in North America, 7177 kHz elsewhere.

John P
 

I heard Tom (VE3THR) for a moment or two, but the noise level is AWFUL!
--
John - WA2FZW

Re: BITX QSO Afternoon/Evening, Sunday, June 17, 3PM & 7PM Local Time, 7277 kHz in North America, 7177 kHz elsewhere.

Jay - WS4JM
 

Heard Tom and another station earlier, most likely John, but couldn't get back to either, still trying!

WS4JM

Anyone ever use one of these to build a Raduino clone?

Dennis Yancey <bigbluedry@...>
 

Has anyone used one of these to build a Raduino clone?  If so, any issues I need to be aware of either hardware Sr software related?

https://www.digikey.com/catalog/en/partgroup/si5351a-clock-generator-breakout-board/55065?utm_adgroup=Programmers%20Dev&slid=&gclid=EAIaIQobChMI7dPJs_Pb2wIVDJFpCh3uVQ_jEAAYASAAEgKikvD_BwE

Re: BITX QSO Afternoon/Evening, Sunday, June 17, 3PM & 7PM Local Time, 7277 kHz in North America, 7177 kHz elsewhere.

Howard Fidel
 

I just heard Tom, VE3THR marine 4, he heard me but didn't copy and then disappeared. Called CQ a few times, didn't hear anyone else.

Howard - WB2VXW

On 6/17/2018 7:45 PM, WS4JM wrote:
Heard Tom and another station earlier, most likely John, but couldn't get back to either, still trying!

WS4JM


Re: BITX QSO Afternoon/Evening, Sunday, June 17, 3PM & 7PM Local Time, 7277 kHz in North America, 7177 kHz elsewhere.

Tom VE3THR
 

Well guys...this was better tonight.  Made one contact WI1B 5x4 about 2310hrs. Only station loud enough to work. Only hearing partial calls from my /mm station. Might give a 40m hamstick a try next wknd. Just have to find the right combo on the water.  Will try to be on wed night sm time and channel. 
73 Tom VE3THR 

Re: BITX QSO Afternoon/Evening, Sunday, June 17, 3PM & 7PM Local Time, 7277 kHz in North America, 7177 kHz elsewhere.

Daniel Conklin <danconklin2@...>
 

Tom (VE3THR/Marine mobile), Nice making contact with you.  Hope to see you down the log! 73, Dan, W2DLC

Re: BITX QSO Afternoon/Evening, Sunday, June 17, 3PM & 7PM Local Time, 7277 kHz in North America, 7177 kHz elsewhere.

Daniel Conklin <danconklin2@...>
 

OK, I just had a successful QSO with Jerry, W0PWE near Des Moine, Iowa!  My first Iowa contact with the uBITX.  Dan, W2DLC

Re: Help with AGC kit wiring

John KC9OJV
 

I built that kit yesterday and it went fine without trouble. It's compact with small parts but not that many pieces to deal with. If someone has drilled a hole, soldered and cut the traces I'd love to see a photo of that with and without the board in place. Thanks for your great contribution Don- Kees too.

John
KC9OJV

Re: ubitx raduino issue/AKA the radio doesn't receive

Dennis Yancey
 

John,
once again, your software saved me tons of time in troubleshooting. It turns out I have a bad 5351 on the Raduino now.. looking for possibilities of replacing it either as a chip or completely as a unit.

Thanks again..
--
72 and God bless
KD4EPG

Re: An Apology and clarification #ubitx

Richard Bennett
 

I would venture a guess that his parcels arrived as they did as he probably rubbed his pleasant attitude on his mail delivery person and has since garnered himself a target for the blatant relief of his postal carriers frustrations.
Yes, I DO believe in karma and am usually pretty tickled when I hear someone of his "caliber" beat their gums....and yet fail to understand why they get what they get.
As for most of us, we knew what we were getting as we did our homework before placing our order.
And he, as competent as he claims, ordered multiples....of such an inferior device.
One would think he could look at the schematic and surmise it totally lacking.
I would agree with others....let us all see your design with all its capabilities and at the same price.....I'll order multiples myself....to my address tho, as my postal carrier is quite a nice chap and takes special care of my deliveries.
73 1/2 (little extra hug for ya)
KD9BPY


On Sun, Jun 17, 2018 at 13:38, Ray Koster via Groups.Io
<raykoster@...> wrote:
I am afraid that your first post is correct and you do need the skills of superman to do any mods to this piece of junk!!. If this is a modders delight rig then why was it built using SMT components? Why does it need to be modded and at the rate these mods keep coming in, there will be very little of the original rig left!!!. If this rig is that bad, then why was it released on to the market with so many faults on it? Has anyone bothered to see if this rig, after all the mod's have been done, still complies with their countries radio spec's? has anybody tried to take legal action against Hf signals for selling such a poorly designed rig that requires so many modifications to make it work?

You may well be asking if this guy has infact any of these kits!!! well I have two Bitx 40's both arrived smashed in the post and beyond repair and a Ubitx that also arrived smashed and is also in a doubtful state of repair. I would not dream of putting this Junk on the air and would doubt that any of these kits would ever work...i am not going to spend weeks looking for cracked components when I can build a lot better things with my time..I am an ex Electronic service engineer and also an ex college lecturer in the field of Electronics, Ex meaning I am now retired


Ray Koster G7BHQ

Display garbled uBitX

John
 

I didn't use my uBitX for a while and today when I hooked it up my display was garbled. I was afraid that my seperation cable might be the problem, but even with the display directly connected to the raduino gives the same result.

When I turn the tune button or push it I see things changing on the display so it looks like the raduino is functioning, Any ideas how to move forward?


John
KG5WJQ