Re: Can't Swap Back to Stock Firmware #firmware #v6


howard winwood G4GPF
 

The baud rate shown hear is 57600, your previous posting with the error messages is 115200, it might be a clue?


On 24 Apr 2020, at 14:34, Zac T <ztread01@...> wrote:

Interesting enough, if I select the Old Boot Loader, I get this:

 

avrdude: Version 6.3-20190619
         Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
         Copyright (c) 2007-2014 Joerg Wunsch

         System wide configuration file is "C:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf"

         Using Port                    : COM5
         Using Programmer              : arduino
         Overriding Baud Rate          : 57600
         AVR Part                      : ATmega328P
         Chip Erase delay              : 9000 us
         PAGEL                         : PD7
         BS2                           : PC2
         RESET disposition             : dedicated
         RETRY pulse                   : SCK
         serial program mode           : yes
         parallel program mode         : yes
         Timeout                       : 200
         StabDelay                     : 100
         CmdexeDelay                   : 25
         SyncLoops                     : 32
         ByteDelay                     : 0
         PollIndex                     : 3
         PollValue                     : 0x53
         Memory Detail                 :

                                  Block Poll               Page                       Polled
           Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW  MaxW   ReadBack
           ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
           eeprom        65    20     4    0 no       1024    4      0  3600  3600 0xff 0xff
           flash         65     6   128    0 yes     32768  128    256  4500  4500 0xff 0xff
           lfuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
           hfuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
           efuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
           lock           0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
           calibration    0     0     0    0 no          1    0      0     0     0 0x00 0x00
           signature      0     0     0    0 no          3    0      0     0     0 0x00 0x00

         Programmer Type : Arduino
         Description     : Arduino
         Hardware Version: 2
         Firmware Version: 1.16
         Vtarget         : 0.0 V
         Varef           : 0.0 V
         Oscillator      : Off
         SCK period      : 0.1 us

avrdude: AVR device initialized and ready to accept instructions

Reading | ################################################## | 100% 0.00s

avrdude: Device signature = 0x1e950f (probably m328p)
avrdude: reading input file "C:\Users\ztrea.000\AppData\Local\Temp\arduino_build_829362/ubitx_v6.3.1_code.ino.hex"
avrdude: writing flash (28256 bytes):

Writing | ################################################## | 100% 8.02s

avrdude: 28256 bytes of flash written
avrdude: verifying flash memory against C:\Users\ztrea.000\AppData\Local\Temp\arduino_build_829362/ubitx_v6.3.1_code.ino.hex:
avrdude: load data flash data from input file C:\Users\ztrea.000\AppData\Local\Temp\arduino_build_829362/ubitx_v6.3.1_code.ino.hex:
avrdude: input file C:\Users\ztrea.000\AppData\Local\Temp\arduino_build_829362/ubitx_v6.3.1_code.ino.hex contains 28256 bytes
avrdude: reading on-chip flash data:

Reading | ################################################## | 100% 6.01s

avrdude: verifying ...
avrdude: 28256 bytes of flash verified

avrdude done.  Thank you.


Join BITX20@groups.io to automatically receive all group messages.