I can’t imagine postage will be much it’s not big. If I just put it and the config board in a jiff bag. It has a voltage regulator a small heatsink that allow it to run from 12V, but you can remove th

Would nice to see it used again. Pass it on to another group when you finish with it, hopefully you don’t lose it It is a 2010 tracker and no longer available from big redbee Steve G6UIM From: aprsisc

Would like to see this used again on a balloon. It’s an older 2m Tracker from bigredbee Bought in 2010 Capable of putting out around 8W but you can configure the power and also the frequency. With con

_____ Sent: 02 March 2014 23:20 To: 'Lynn W Deffenbaugh (Mr)' Cc: 'apsisce@...' Subject: RE: GPS PRN 40 Yep seems its part of the GAGAN system run by India. Am surprised I get that better

Left click on the station which will bring up a menu then select follow, that will show a track with a point each time a beacon was received. It will centre the station on screen and keep it centred a

If I do 9k6 it will be in conjunction with 1k2 that is both on 70cm. probably on the same frequency It may or may not happen. An is only really going to be an experiment at the moment. Cross band is d

The one option I can think of is recording audio on say a mp3 device and playing it back through a soundcard. APRSIS32 will interface with a number of sound modem systems. Or setting up a general inst

Yes thought as much, but I don’t see a high level of traffic happening, so really not much point I guess in 9600. Although I could run 9600 and 1200 on 70cm but only cross band 1200. Thanks for the co

I am building a cross band digi/igate is there an advantage in running 9600 baud on the 70cm side? There is the obvious problem it might flood the 1200 baud side, but I don’t see there being that much

Yes. Go to screen/labels and tick the altitude option, for a balloon I would select a speed option as well. Tick footprint while you are there. I forget the defaults but they can be changed in configu

The D710 is similar to the D72 I believe, I am new using a D72 but you need to load the Kenwood virtual serial port driver and then set APRSIS32 to use that com port. You might need to edit the APRSIS

There is a WIKI page on the subject of setting up for ISS operation http://aprsisce.wikidot.com/doc:satelliteops The 2 big no's are unattended transmitting and gating of other station through the ISS.

I need to go through the WIKI info as there are commands there not listed in the manual. And some things I don't see the point in doing such as turning off the message display on the radio etc. Mostly

I used the setup from the WIKI which is the KWD710(APRS) port your suggestion about the TNC being off was the answer. Am a newbie with it will edit the closecmds to put it back on when exiting. Seemed

I used the commands listed on the WIKI to connect the Radio to APRSIS32 all seemed to work ok But on closing the program and trying to use the radio stand alone, the radio now refuses to let me turn t

Got it today and setting up. seem to have most things sorted but not CTCS tones it seems. Anyway if anyone can message G6UIM-9 for a test would be good. Next up is sorting it using QSY functions which

Well it's brand new lost/stolen on the way to me. So not setup. Most likely if Stolen will be sold to an unsuspecting amateur on ebay or similar. The company I bought it from are sending another, I ca

I ordered a TH-D72 and it got lost at the Royal Mail Exeter depot. I have another on the way. But it would be nice to get hold of the original. I have not lost money as it was covered. On the off chan

in response to an email I received about crossband digipeating and RAYNET. Locally RAYNET use 144.775MHz for voice comms.this is obviously a problem with APRS being on 144.800MHz. In the past we have

My phone line failed this morning and apparently it's going to be a week before they fix it. I went into town and bought a Pay as you go broadband dongle not a bad deal £30 for 1GB a month for 3 month