Date   
Re: Kenwood D710GA and APRS Ports question

KD7YZ Bob
 

Ah, OK.
The only way I know to send a screenshot-like foto is via email to this 'forum'.

BUT ...in my case only, when I rely solely on interchange with said Forum, through email, my "stuff" , somewhere, never relays only occasional, replies, randomly.

So I just use the web interface ...sadly today I needed to send a jpeg, so reverted to ermail

thanks for un-moderation.


--
--
KD7YZ Bob EM88LL

Re: Kenwood D710GA and APRS Ports question

Steve
 

as your post had an attachment it seemed to have ended up in moderation so I took it out of moderation, that should not happen again.

73
Steve,  kf6wax

On Sun, Mar 8, 2020 at 2:59 PM KD7YZ Bob <kd7yz@...> wrote:
Ahhh, I seeeeee ....an hour-ish later the original got posted ... and my boo-boo second sending of it ...

--
--
KD7YZ Bob EM88LL



Re: Kenwood D710GA and APRS Ports question

KD7YZ Bob
 

Ahhh, I seeeeee ....an hour-ish later the original got posted ... and my boo-boo second sending of it ...

--
--
KD7YZ Bob EM88LL

Kenwood D710GA and APRS Ports question

KD7YZ Bob
 

Lynn, back in a reply of yours:
https://groups.io/g/APRSISCE/message/33860

You said if I wanted to try and DigiPeat from said D710, that I might try an APRS type port ... I assume, inside APRSIS32.

Or, have AGWPE-Pro make a port to the D710 ....presumably then, pass info via the TelNet port into APRIS32.

I have looked at the available Templates when creating a new-port in APRSIS32, but only see one with an APRS designation ... as seen in attached jpeg.

To refresh anyone's memory, this is what I see in the Digipeat log:

---------------------------------------------------
WinMain:2020-03-08T04:11:34.557 Digipeating KI7PLN-9 (WIDE1-1) via(WIDE1-1=WIDE1*)

WinMain:2020-03-08T04:11:34.557 Original(KI7PLN-9>DIBY5Z,WIDE1-1,WIDE2-1:`o`r"N>/`"6j}144.390MHz Ramblin'_))

WinMain:2020-03-08T04:11:34.558 Transmit(KI7PLN-9>DIBY5Z,KD7YZ-15*,WIDE1*,WIDE2-1:`o`r"N>/`"6j}144.390MHz Ramblin'_))

WinMain:2020-03-08T04:11:34.558 KWD710(APRS):DigiPeating Not Supported on KWD710(APRS) Protocol Ports

-------------------------------------------------------------------

So the other alternative was to try and make AGWPE do it. And as far as I can see, AGWPE can ONLY work the D710 when the D710 is in Packet mode.

Perhaps I'm wrong on that one.

The myriad good links y'all have had me read have mentioned that one can let the D710 do all the APRS and just let APRSIS32 get input data from something like AGWPE.

Or one can have APRSIS32 do ALL the work.

So I let AGWPE read the COM port out of the D710's "other" channel, which I set on 145.825 ... to copy satellites.

I leave Ch-A on 144.390 to handle things as I learn them.

If I run UISS after/with AGWPE, IT can DigiPeat some things, and has.

There is a setting in the D710, UIDIGI, that I have "On".
I set "Aliases" to WIDE-1, WIDE2-1, WIDE2-2.

The logic of that came from reading dozens of PDF's and Wiki's, as I said, from y'all.

But I can't tell if UISS or the D710 is the cause of a DigiPeat .... thus I wanted to try and make APRSIS32 do all the work ... as it is MUCH smarter than I am.


thanks help
--
73
Bob KD7YZ
AMSAT LM #901

Kenwood D710GA and APRS Ports question

KD7YZ Bob
 

Lynn, back in a reply of yours
https://groups.io/g/APRSISCE/message/33860

You said if I wanted to try and DigiPeat from said D710, that I might try an APRS type port ... I assume, inside APRSIS32.

Or, have AGWPE-Pro make a port to the D710 ....presumably then, pass info via the TelNet port into APRIS32.

I have looked at the available Templates when creating a new-port in APRSIS32, but only see one with an APRS designation ... as seen in attached jpeg.

To refresh anyone's memory, this is what I see in the Digipeat log:

---------------------------------------------------
WinMain:2020-03-08T04:11:34.557 Digipeating KI7PLN-9 (WIDE1-1) via(WIDE1-1=WIDE1*)

WinMain:2020-03-08T04:11:34.557 Original(KI7PLN-9>DIBY5Z,WIDE1-1,WIDE2-1:`o`r"N>/`"6j}144.390MHz Ramblin'_))

WinMain:2020-03-08T04:11:34.558 Transmit(KI7PLN-9>DIBY5Z,KD7YZ-15*,WIDE1*,WIDE2-1:`o`r"N>/`"6j}144.390MHz Ramblin'_))

WinMain:2020-03-08T04:11:34.558 KWD710(APRS):DigiPeating Not Supported on KWD710(APRS) Protocol Ports

-------------------------------------------------------------------

So the other alternative was to try and make AGWPE do it. And as far as I can see, AGWPE can ONLY work the D710 when the D710 is in Packet mode.

Perhaps I'm wrong on that one.

The myriad good links y'all have had me read have mentioned that one can let the D710 do all the APRS and just let APRSIS32 get input data from something like AGWPE.

Or one can have APRSIS32 do ALL the work.

So I let AGWPE read the COM port out of the D710's "other" channel, which I set on 145.825 ... to copy satellites.

I leave Ch-A on 144.390 to handle things as I learn them.

If I run UISS after/with AGWPE, IT can DigiPeat some things, and has.

There is a setting in the D710, UIDIGI, that I have "On".
I set "Aliases" to WIDE-1, WIDE2-1, WIDE2-2.

The logic of that came from reading dozens of PDF's and Wiki's, as I said, from y'all.

But I can't tell if UISS or the D710 is the cause of a DigiPeat .... thus I wanted to try and make APRSIS32 do all the work ... as it is MUCH smarter than I am.


thanks help
--
73
Bob KD7YZ
AMSAT LM #901

Re: Testing Email access to forum

KD7YZ Bob
 

Bad sign.
Text message arrived straight away, under two seconds.

will retry the original question to Lynn with the attached Jpeg

--
--
KD7YZ Bob EM88LL

Testing Email access to forum

KD7YZ Bob
 

Ignore.
I sent an email with single jpeg, small size, over an hour ago and don't see it reflected here.

Thus, testing short all-text message.
--
73
Bob KD7YZ
AMSAT LM #901

Re: Filter Out Objects

 


Can someone please show me how to write the code for a filter to be able to turn off objects like winlink with a red diamond and W?


Seems like the hotpots have bloomed and they're now sending two id packets ( w1aw-X and "w1aw  X"). 

Resource discovery with APRS is good but now it's too many too often cluttering the heard list.

Lynn's -s.. helped 

Even better, add. -d/TCPIP*/


Bill

Development version? Was: APRSIS 32

Bob Burns W9BU
 

On 2/24/2020 8:42 PM, Lynn Deffenbaugh wrote:
You need the latest development version for "Never" support.
I'm familiar with the development version and I run it on my computers.

But, this begs question, should the current dev version become the public build? Imagine someone just getting interested in APRS. His buddies tell him to download APRISCE/32. But, when he goes looking, the newest version he can find is from 2012. Eight years ago?

Lynn, I know you're busy. I know you do this as a not-for-profit endeavor. And, your loyal users, including me, love your program. Is there anything we can do to help you move the dev version to the public build?

Bob...

Re: Filter Out Objects

Lynn Deffenbaugh
 

Did I test it?  Yes, that's why I mentioned that you could test it yourself if you used APRSIS32 which includes a filter test capability, but only in a positive sense.

READ the definition of the s filter from the quoted page:

s/pri/alt/over Symbol filter pri = symbols in primary table (| => /)
alt = symbols in alternate table (| => /)
over = overlay character (case sensitive)
For example:
s/->     This will pass all House and Car symbols (primary table)
s//#     This will pass all Digi with or without overlay
s//#/T   This will pass all Digi with overlay of capital "T"

Note that PRIMARY table symbols go after the first FORWARD slash and alternate table (ones that can use overlays) go after the SECOND slash and the overlays go after the THIRD slash and are CaSe SeNsItIvE.

So, if we look at one of the stations you want to get rid of, say N7LOB-10 at http://aprs.fi/N7LOB-10 and then click on the Raw Packets link, we see that they all come from WINLINK and look like:


2020-03-07 07:23:00 EST: WINLINK>APWL2K,TCPIP*,qAS,WLNK:;KD7IIW-10*071222z4151.  NW11152.  Wa144.950MHz 1200 R5m Winlink Gateway

2020-03-07 07:23:02 EST: WINLINK>APWL2K,TCPIP*,qAS,WLNK:;KD7IIW-11*071223z4206.  NW11152.  Wa144.950MHz 1200 R5m Winlink Gateway
2020-03-07 07:23:03 EST: WINLINK>APWL2K,TCPIP*,qAS,WLNK:;KD7NHC-10*071223z3848.  NW11922.  Wa145.090MHz 1200 R8m Winlink Gateway
2020-03-07 07:23:05 EST: WINLINK>APWL2K,TCPIP*,qAS,WLNK:;KD7TNG-10*071223z4213.  NW12147.  Wa145.050MHz 1200 R5m Winlink Gateway
2020-03-07 07:23:07 EST: WINLINK>APWL2K,TCPIP*,qAS,WLNK:;KD7UHR-10*071223z3841.  NW08952.  Wa145.070MHz 1200 R5m Winlink Gateway
2020-03-07 07:23:08 EST: WINLINK>APWL2K,TCPIP*,qAS,WLNK:;KD7X-10  *071223z4818.  NW12237.  Wa145.630MHz 1200 R5m Winlink Gateway
2020-03-07 07:23:10 EST: WINLINK>APWL2K,TCPIP*,qAS,WLNK:;KD7ZDO-10*071223z4521.  NW12237.  Wa145.570MHz 1200 R5m Winlink Gateway
2020-03-07 07:23:12 EST: WINLINK>APWL2K,TCPIP*,qAS,WLNK:;KD8THX-10*071223z4246.  NW08607.  Wa145.070MHz 1200 R5m Winlink Gateway
2020-03-07 07:23:14 EST: WINLINK>APWL2K,TCPIP*,qAS,WLNK:;KD8VAJ-10*071223z3908.  NW08432.  Wa145.010MHz 1200 R5m Winlink Gateway

But APRSIS32 makes this easier by showing:

N7LOB-10
1200 R5m Winlink Gateway

Freq: 145.630MHz
Sym: WinLink (Wa)
App: WinAPRS, etc (L2K)
Ambiguity: 1 nm
FromME: 2659mi NW (311º)
GridSquare: CN86cx
4658.50N 12347.50W
Time: 00-07 11:59:00z
2020-03-07 11:59:16 (18m54s)
WINLINK->TCPIP*

Note that the symbol is Wa.  This means alternate table (since the first character isn't /) symbol a with an overlay of W.

Finding one of the DSTAR objects is a bit trickier since they have an embedded space, but if you search for KB7ZEN* in aprs.fi's Raw Packets display, you get:

2020-03-06 21:42:10 EST: KB7ZEN-S>APDG01,TCPIP*,qAC,KB7ZEN-GS:;KB7ZEN B *070242z4656.40ND12236.00Wa/A=000010RNG0001 440 Voice 438.50000MHz +0.0000MHz
2020-03-06 21:42:20 EST: KB7ZEN-B>APDG02,TCPIP*,qAC,KB7ZEN-BS:!4656.40ND12236.00W&/A=000010RNG0001 440 Voice 438.50000MHz +0.0000MHz
2020-03-06 22:03:30 EST: KB7ZEN-S>APDG01,TCPIP*,qAC,KB7ZEN-GS:;KB7ZEN B *070303z4656.40ND12236.00Wa/A=000010RNG0001 440 Voice 438.50000MHz +0.0000MHz
2020-03-06 22:03:40 EST: KB7ZEN-B>APDG02,TCPIP*,qAC,KB7ZEN-BS:!4656.40ND12236.00W&/A=000010RNG0001 440 Voice 438.50000MHz +0.0000MHz
2020-03-06 22:24:50 EST: KB7ZEN-S>APDG01,TCPIP*,qAC,KB7ZEN-GS:;KB7ZEN B *070324z4656.40ND12236.00Wa/A=000010RNG0001 440 Voice 438.50000MHz +0.0000MHz
2020-03-06 22:24:50 EST: KB7ZEN-B>APDG02,TCPIP*,qAC,KB7ZEN-BS:!4656.40ND12236.00W&/A=000010RNG0001 440 Voice 438.50000MHz +0.0000MHz

Which APRSIS32 kindly describes as:

KB7ZEN B
440 Voice 438.50000MHz +0.0000MHz

Sym: DARES (Da)
App: D-Star Gateway (01)
Range: 1mi
FromME: 2604mi NW (311º)
GridSquare: CN86qw +9ft
4656.40N 12236.00W
Time: 00-07 12:09:00z
2020-03-07 12:09:50 (19m24s)
KB7ZEN-S->TCPIP*

Which is the same alternate table a symbol with an overlay of D.

So plugging alternate table with overlays D and W into the formula for the s filter, we get:

s//a/DW

When I put that filter into an APRSIS32 Filter Test window, I get LOTS of packets including:

WinMain:2020-03-07T12:30:40.967 IS[Firenet](Hit(s//a/D (0x440161))) [0]KB9MNM-S>APDG01,TCPIP*,qAC,KB9MNM-GS:;KB9MNM B *071230z4142.26ND08820.07Ea/A=000010RNG0001 440 Voice 445.60000MHz +0.0000MHz WinMain:2020-03-07T12:30:41.026 IS[APRS-IS](Hit(s//a/D (0x440161))) [1]KB9MNM-S>APDG01,TCPIP*,qAC,KB9MNM-GS:;KB9MNM B *071230z4142.26ND08820.07Ea/A=000010RNG0001 440 Voice 445.60000MHz +0.0000MHz WinMain:2020-03-07T12:30:41.429 IS[APRS-IS](Hit(s//a/D (0x440161))) [0]CN8IC-S>APDG01,TCPIP*,qAC,CN8IC-GS:;CN8IC B *071230z3534.20ND00522.20WaRNG0001 440 Voice 438.45000MHz -8.0000MHz WinMain:2020-03-07T12:30:41.479 IS[Firenet](Hit(s//a/D (0x440161))) [1]CN8IC-S>APDG01,TCPIP*,qAC,CN8IC-GS:;CN8IC B *071230z3534.20ND00522.20WaRNG0001 440 Voice 438.45000MHz -8.0000MHz WinMain:2020-03-07T12:30:41.769 IS[Firenet](Hit(s//a/W (0x570161))) [0]WINLINK>APWL2K,TCPIP*,qAS,WLNK:;OE9XRK-10*071230z4716. NW00937. Ea438.000MHz 9600 R5m Winlink Gateway WinMain:2020-03-07T12:30:41.771 IS[Firenet](Hit(s//a/D (0x440161))) [0]DB0DJ-S>APJIO4,TCPIP*,qAC,DB0DJ-GS:;DB0DJ A *021149z4852.70ND00830.45EaRNG0040 1.2 Voice 1298.575MHz -28MHz WinMain:2020-03-07T12:30:41.794 IS[APRS-IS](Hit(s//a/W (0x570161))) [1]WINLINK>APWL2K,TCPIP*,qAS,WLNK:;OE9XRK-10*071230z4716. NW00937. Ea438.000MHz 9600 R5m Winlink Gateway WinMain:2020-03-07T12:30:41.795 IS[APRS-IS](Hit(s//a/D (0x440161))) [1]DB0DJ-S>APJIO4,TCPIP*,qAC,DB0DJ-GS:;DB0DJ A *021149z4852.70ND00830.45EaRNG0040 1.2 Voice 1298.575MHz -28MHz

Which kindly tells me that packets were hitting on both the D and W overlay characters which is confirmed if you use the aprs101.pdf to visually parse the packet data and find the symbol and overlay characters that match.

Further, if I telnet to my local friendly APRS-IS server and set up that filter (see http://www.aprs-is.net/Connecting.aspx for instructions), I get the following packets:

VK2RBV-S>APDG01,TCPIP*,qAC,VK2RBV-GS:;VK2RBV B *071233z3351.84SD15112.68EaRNG0050 440 Voice 438.77500MHz +5.0000MHz VA2REX-S>APJIO4,TCPIP*,qAC,VA2REX-GS:;VA2REX AD*221404z4500.92ND07350.48WaRNG0020 1.2 Data 1248.50Mhz 128K VA2REX-S>APJIO4,TCPIP*,qAC,VA2REX-GS:;VA2REX B *022035z4500.92ND07350.48WaRNG0040 440 Voice 448.325Mhz - 5Mhz DO9MC-S>APDG01,TCPIP*,qAC,DO9MC-GS:;DO9MC B *071233z5145.32ND00800.88Ea/A=000010RNG0001 440 Voice 439.93750MHz -9.4000MHz WX4EMA-S>APJIO4,TCPIP*,qAC,WX4EMA-GS:;WX4EMA C *061725z3250.15ND08337.97WaRNG0015 2m Voice 145.340 +0.600 MHz WINLINK>APWL2K,TCPIP*,qAS,WLNK:;VE7LAN-10*071233z4921. NW12257. Wa145.070MHz 1200 R5m Winlink Gateway F5ZLG-S>APJIO4,TCPIP*,qAC,F5ZLG-GS:;F5ZLG B *061711z4334.90ND00129.98EaRNG0030 430 Voice 439.925 -9.4 MHz KN6BDP-S>APDG01,TCPIP*,qAC,KN6BDP-GS:;KN6BDP B *071233z5000.00ND00300.00WaRNG0001 440 Voice 438.80000MHz +0.0000MHz

Which you can see (if you've studied aprs101.pdf and can visually parse packets) includes both the D and W overlays of the alternate table a symbol.

So, yes, I've tested the recommended filter in the positive sense.  Testing a negative filter is much harder in that you have to go through a large (I use planet-wide) stream of data and determine that the target packets are NOT present.

So, my challenge to you is did YOU apply and test the negative form of the filter properly?  What makes you believe it "did not work"?  Is it possible that it DID work and SARTRACK is simply displaying stations that it heard before the negative filter was applied?  Did SARTRACK truly apply the negative filter to the upstream APRS-IS server connection?

And if you need help confirming those questions, please inquire on the SARTRACK support list as they are not APRS-general questions.

Lynn (D) - KJ4ERJ - Author of APRSISCE for Windows Mobile and Win32

PS.  An alternat esymbol to get rid of all packets from WinLink would be -b/WINLINK or -u/APWL2K.  For the DStar gateways, you could use -u/APDG* or -u/APDG01/APDG02.  The trick to filtering APRS-IS is to deterine what common feature is shared by the target stations' packets and NOT shared by desired station packets.


On 3/7/2020 3:15 AM, Jerry N7YGE wrote:

Did not work.  Did you try it and it worked for you?  See below as to the right orientation of the /a for a red diamond.  Yes I am using SARTRACK but all programs have the filter box and is universal.  So should work for all aprs programs.  Please send code tested and works for you.

 

 

http://aprsisce.wikidot.com/aprs-is-filters

 

 

-s//a/DW

Blocks all packets using a red diamond (\a) overlaid with DW

 

 

Since the diamond is red should it use the \a and not /a?

 

 

-s/\a/DW

 

Thank you.

 

 

Jerry N7YGE

 

From: APRSISCE@groups.io [mailto:APRSISCE@groups.io] On Behalf Of Lynn Deffenbaugh
Sent: Friday, March 6, 2020 5:49 PM
To: APRSISCE@groups.io
Subject: Re: [APRSISCE] Filter Out Objects

 

Nice map, but I don't think that's APRSIS32...  If it was, you could test the positive filter with Control-G for a filter test.  But here's what I think you need:

-s//a/WD

Yes, there's 2 slashes after the s and one slash after the a.  It says to suppress all "a" symbols from the alternate table (the red diamond) with an overlay of W or D.

You can read more about APRS-IS filters at:

http://www.aprs-is.net/javAPRSFilter.aspx

Lynn (D) - KJ4ERJ - Author of APRSISCE for Windows Mobile and Win32

On 3/6/2020 6:14 PM, Jerry N7YGE wrote:

I want all of the red diamond with W and D’s to go away.  Picky any of them.

 

Thank you for the help.

 

 

 

From: APRSISCE@groups.io [mailto:APRSISCE@groups.io] On Behalf Of Lynn Deffenbaugh
Sent: Friday, March 6, 2020 12:49 PM
To: APRSISCE@groups.io
Subject: Re: [APRSISCE] Filter Out Objects

 

-o is an object filter which is based on the object name.

I suspect you're looking for a -s filter which is a symbol filter.

Please give me a few of the stations you'd like to not see so that I can verify exactly which symbol they're using to build you a suitable -s/ symbol filter.

Lynn (D) - KJ4ERJ - Author of APRSISCE for Windows Mobile and Win32

On 3/6/2020 12:22 PM, Jerry N7YGE wrote:

 

Can someone please show me how to write the code for a filter to be able to turn off objects like winlink with a red diamond and W? Also black diamond with a D.

 

I have tried  filter –o/a/DW and -0/a\DW

 

Jerry N7YGE

 

Re: Filter Out Objects

Jerry N7YGE
 

Did not work.  Did you try it and it worked for you?  See below as to the right orientation of the /a for a red diamond.  Yes I am using SARTRACK but all programs have the filter box and is universal.  So should work for all aprs programs.  Please send code tested and works for you.

 

 

http://aprsisce.wikidot.com/aprs-is-filters

 

 

-s//a/DW

Blocks all packets using a red diamond (\a) overlaid with DW

 

 

Since the diamond is red should it use the \a and not /a?

 

 

-s/\a/DW

 

Thank you.

 

 

Jerry N7YGE

 

From: APRSISCE@groups.io [mailto:APRSISCE@groups.io] On Behalf Of Lynn Deffenbaugh
Sent: Friday, March 6, 2020 5:49 PM
To: APRSISCE@groups.io
Subject: Re: [APRSISCE] Filter Out Objects

 

Nice map, but I don't think that's APRSIS32...  If it was, you could test the positive filter with Control-G for a filter test.  But here's what I think you need:

-s//a/WD

Yes, there's 2 slashes after the s and one slash after the a.  It says to suppress all "a" symbols from the alternate table (the red diamond) with an overlay of W or D.

You can read more about APRS-IS filters at:

http://www.aprs-is.net/javAPRSFilter.aspx

Lynn (D) - KJ4ERJ - Author of APRSISCE for Windows Mobile and Win32

On 3/6/2020 6:14 PM, Jerry N7YGE wrote:

I want all of the red diamond with W and D’s to go away.  Picky any of them.

 

Thank you for the help.

 

 

 

From: APRSISCE@groups.io [mailto:APRSISCE@groups.io] On Behalf Of Lynn Deffenbaugh
Sent: Friday, March 6, 2020 12:49 PM
To: APRSISCE@groups.io
Subject: Re: [APRSISCE] Filter Out Objects

 

-o is an object filter which is based on the object name.

I suspect you're looking for a -s filter which is a symbol filter.

Please give me a few of the stations you'd like to not see so that I can verify exactly which symbol they're using to build you a suitable -s/ symbol filter.

Lynn (D) - KJ4ERJ - Author of APRSISCE for Windows Mobile and Win32

On 3/6/2020 12:22 PM, Jerry N7YGE wrote:

 

Can someone please show me how to write the code for a filter to be able to turn off objects like winlink with a red diamond and W? Also black diamond with a D.

 

I have tried  filter –o/a/DW and -0/a\DW

 

Jerry N7YGE

 

Re: Filter Out Objects

Lynn Deffenbaugh
 

Nice map, but I don't think that's APRSIS32...  If it was, you could test the positive filter with Control-G for a filter test.  But here's what I think you need:

-s//a/WD

Yes, there's 2 slashes after the s and one slash after the a.  It says to suppress all "a" symbols from the alternate table (the red diamond) with an overlay of W or D.

You can read more about APRS-IS filters at:

http://www.aprs-is.net/javAPRSFilter.aspx

Lynn (D) - KJ4ERJ - Author of APRSISCE for Windows Mobile and Win32

On 3/6/2020 6:14 PM, Jerry N7YGE wrote:

I want all of the red diamond with W and D’s to go away.  Picky any of them.

 

Thank you for the help.

 

 

 

From: APRSISCE@groups.io [mailto:APRSISCE@groups.io] On Behalf Of Lynn Deffenbaugh
Sent: Friday, March 6, 2020 12:49 PM
To: APRSISCE@groups.io
Subject: Re: [APRSISCE] Filter Out Objects

 

-o is an object filter which is based on the object name.

I suspect you're looking for a -s filter which is a symbol filter.

Please give me a few of the stations you'd like to not see so that I can verify exactly which symbol they're using to build you a suitable -s/ symbol filter.

Lynn (D) - KJ4ERJ - Author of APRSISCE for Windows Mobile and Win32

On 3/6/2020 12:22 PM, Jerry N7YGE wrote:

 

Can someone please show me how to write the code for a filter to be able to turn off objects like winlink with a red diamond and W? Also black diamond with a D.

 

I have tried  filter –o/a/DW and -0/a\DW

 

Jerry N7YGE

 

Re: Filter Out Objects

Jerry N7YGE
 

I want all of the red diamond with W and D’s to go away.  Picky any of them.

 

Thank you for the help.

 

 

 

From: APRSISCE@groups.io [mailto:APRSISCE@groups.io] On Behalf Of Lynn Deffenbaugh
Sent: Friday, March 6, 2020 12:49 PM
To: APRSISCE@groups.io
Subject: Re: [APRSISCE] Filter Out Objects

 

-o is an object filter which is based on the object name.

I suspect you're looking for a -s filter which is a symbol filter.

Please give me a few of the stations you'd like to not see so that I can verify exactly which symbol they're using to build you a suitable -s/ symbol filter.

Lynn (D) - KJ4ERJ - Author of APRSISCE for Windows Mobile and Win32

On 3/6/2020 12:22 PM, Jerry N7YGE wrote:

 

Can someone please show me how to write the code for a filter to be able to turn off objects like winlink with a red diamond and W? Also black diamond with a D.

 

I have tried  filter –o/a/DW and -0/a\DW

 

Jerry N7YGE

 

Re: Filter Out Objects

Lynn Deffenbaugh
 

-o is an object filter which is based on the object name.

I suspect you're looking for a -s filter which is a symbol filter.

Please give me a few of the stations you'd like to not see so that I can verify exactly which symbol they're using to build you a suitable -s/ symbol filter.

Lynn (D) - KJ4ERJ - Author of APRSISCE for Windows Mobile and Win32

On 3/6/2020 12:22 PM, Jerry N7YGE wrote:

 

Can someone please show me how to write the code for a filter to be able to turn off objects like winlink with a red diamond and W? Also black diamond with a D.

 

I have tried  filter –o/a/DW and -0/a\DW

 

Jerry N7YGE

 

Filter Out Objects

Jerry N7YGE
 

 

Can someone please show me how to write the code for a filter to be able to turn off objects like winlink with a red diamond and W? Also black diamond with a D.

 

I have tried  filter –o/a/DW and -0/a\DW

 

Jerry N7YGE

 

Re: Beacon Time-Only yields Time of (Time 0:00:00)

KD7YZ Bob
 

"You might want to set a comment on your station and uncheck Configure / Beacon / Why."

2:Fm KD7YZ-15 To APWW10 Via WIDE2-2 <UI pid=F0 Len=78 >[07:58:59]
=3829.65N/08300.99W-PHG6/60 & D710GA & Stacked 2m Loops 50' AGL on Ridgeline

There! Looks good now.

Thanks


--
KD7YZ Bob EM88LL

Re: Beacon Time-Only yields Time of (Time 0:00:00)

Lynn Deffenbaugh
 

Beaconing is a good thing because it lets other APRS users know that you're at least semi-interested.  And you have the perfect use for Time Only, fixed stations.  With Time Only checked, APRSIS32 will beacon at the configured Max Time rate.

You might want to set a comment on your station and uncheck Configure / Beacon / Why.  That latter is where the (Time 0:00:00) which is why the beacon was sent.  Why makes sense when you're debugging various Genius Beacon settings, but definitely not for a fixed station or Time Only configuration because it will always say the same thing.

Lynn (D) - KJ4ERJ - Author of APRSISCE for Windows Mobile and Win32

On 2/28/2020 6:32 AM, KD7YZ Bob wrote:
So, I have Genius-Beaco9ning set at 5/15 Mins and Time-Only Checked.
I have GPS Disabled since I am a fixed-location, Home.

However, when the beacon fires I see what's below.:

1:Fm KD7YZ-15 To APWW10 Via WIDE2-2 <UI pid=F0 Len=34 >[06:21:48]
=3829.65N/08300.99W-(Time 0:00:00)

I go back and forth, in this APRS learning curve, of allowing a beacon and not-allowing any form of beacon from either the program, or from the Kenwood D710.

Maybe it's moot point and I don't need a beacon in a rather unpopulated portion of the country. Well, OK, there is upstate Nevada, Wyoming ...hmmmm

GM and thanks for any replies.
--
KD7YZ Bob EM88LL

Beacon Time-Only yields Time of (Time 0:00:00)

KD7YZ Bob
 

So, I have Genius-Beaco9ning set at 5/15 Mins and Time-Only Checked.
I have GPS Disabled since I am a fixed-location, Home.

However, when the beacon fires I see what's below.:

1:Fm KD7YZ-15 To APWW10 Via WIDE2-2 <UI pid=F0 Len=34 >[06:21:48]
=3829.65N/08300.99W-(Time 0:00:00)

I go back and forth, in this APRS learning curve, of allowing a beacon and not-allowing any form of beacon from either the program, or from the Kenwood D710.

Maybe it's moot point and I don't need a beacon in a rather unpopulated portion of the country. Well, OK, there is upstate Nevada, Wyoming ...hmmmm

GM and thanks for any replies.
--
KD7YZ Bob EM88LL

Re: APRSIS 32

ve6frc@...
 

Ok, Thanks for that. Will give it a go shortly.
Thanks again.
Fred Cnossen
VE6FRC

Re: APRSIS 32

Lynn Deffenbaugh
 

You need the latest development version for "Never" support.  Read:

http://aprsisce.wikidot.com/doc:development-version

Lynn (D) - KJ4ERJ - Author of APRSISCE for Windows Mobile and Win32

On 2/24/2020 5:53 PM, ve6frc@... wrote:
Build 2012/08/30 09:19