If you are using AGWpe to interface with the SignaLink, then the RF port would be of TYPE AGW. WHat are you using to show the "AGWPE decode"? AGWMonitor, AGWTerm, or something else? Logging is in

There is a separate Port(xxxx) logging enable for every port that has been defined. Enable the one you want, then enable the View Logs for that port, and you should see a new window open with

I think, tho, that he's asking if there's a log to show the packets that are being received from the port that he's defined as the Signalink port. Kinda like a live monitor window of incoming RF

Lynn, FYI, there's: - IGate - IGate(Filter) - Igate(NOT) - iGateEnabled Greg KO6TH Lynn Deffenbaugh wrote:

Look for a Trace Log called Port(<YourPortName>) and enable it.  You should also see these in the IGate Trace Log if the correct options are chosen on the port configuration dialog to gate the

I do not see a way in APRSIS32 to read or see or log data coming in from the SignaLink Soundcard which is plugged into the D710GA data port. However, AGWPE can see it as here is a recent

They have pretty good technical service (662-323-0549) and their full 12-month warranty is described on the last page of the manual. They had a 1 year "no matter what" warranty, but it doesn't look

Rob, I wasn't aware they had one but I'll check it out. Thanks for the head's up. 73, Don W4GCW Where am I? Click link below. https://aprs.fi/#!call=a%2FW4GCW-9&timerange=3600&tail=3600

Don't forget the MFJ gaurantee. I'd definitely contact them, and let them know. I do have to say that I am very surprised as the TNC-X (MFJ-1270X) are such simple devices. Not much to go

Rob and Lynn, Thank you guys for your help and assistance. I've changed all cables and replaced the MFJ 1270x tnc with an old KAM and now APRSIS32 is working like a champ. 73, Don W4GCW

The MFJ-1270X only has KISS mode. The PIC16F628P firmware is a KISS TNC only. Encode and decode iof the audio tones are done through an old BELL202 modem chip (not firmware). The DCD LED is

Hi Rob, I appreciate your reply. Equipment here is an MFJ-1270X powered via serial cable and a Yaesu FT2600. I'm able to see received packets via the yellow light on the tnc and the signal bar on the

Is the TNC in question the MFJ-1270X? You state MFJ-1279X in another email and I couldn't find that. You don't state if there are any LEDS on, but I will assume you are powering the TNC-X (MFJ-1270X)

Lynn, It's looking like the problem is with the tnc. I downloaded Pin Point APRS software and had the same results, no tx or rx with either program. I'm going to take the tnc out of kiss and see it

Good morning Lynn, I've verified that the tnc is in KISS mode. What's next? Thanks. 73, Don

Is the TNC locked into KISS mode? And did you use a Simply(KISS) type port in the configuration? The other thing to try is closing APRSIS32 and open the COM port to the TNC in a simple

Lynn, The tnc is an MFJ1279X and yes, it's configured in APRSIS32. Received nothing. 73, Don W4GCW Where am I? Click link below. https://aprs.fi/#!call=a%2FW4GCW-9&timerange=3600&tail=3600

What TNC is it? How do you have it configured in APRSIS32? What port type did you use? So many questions that need answers! Are you seeing any packets from the radio which would be shown

HI Lynn and thanks for taking the time to reply to my call for help.I found and deleted the xml file and was able to download APRSIS32 with only one problem. The radio/tnc won't transmit. I've run