Hi Lynn/Robert, I am seeing this packet in the APRS-IS packet stream window (print screen attached) for my primary station VU3NUF. 'Telemetry is controlled via Enables / Telemetry Enabled or via

The ISS by itself doesn't beacon a location so it won't appear on the map. However, I inject an ISS object every 2 minutes showing the orbital location of the ISS and the estimated RF

That is the telemetry beacon.

As far as I know, the only way to get the development version is through the "About" check. If the download starts and fails, then it is most likely the things you are looking at: 1. Anti-Virus 2.

Is there a filter or a setting someone could post all I want to see on the map is the international space station.

I checked aprs.fi's raw packets for VU3NUF and do not see the telemetry (2nd) packet. Where are you seeing this packet and for what station? If it is in a trace log, it may be shown as

Hi! When I click on transmit or let the beacons generate at the beacon interval, 2 beacons are being generated: 1. APWW10,TCPIP*,qAC,T2SWEDEN2:@162054h3043.84N/07647.85E-Hi de Baba! Chandigarh,

I am not following your description: iGate is KD9EEE iGate is KD9EEE-1 I think your IGate is the APRSIS32 instance and your DIGI is the D710? The only way I know of changing the position in

I have been trying to update the development version of APRSIS to the 11/07/18 release since its release, but every time I attempt to download it results in a "download failed" message. Is there a

I set up my digipeater and igate. Kenwood TM-D710A, Windows 7 pro running in a VMWare fusion VM. Everything WAS fine. Today I get home and my iGate thinks it is on the other side of Milwaukee. Don't

It worked, thanks! There is one step between 1 and 2 (click Dispatch). This also cleared the lingering APRS stations. I am going to write and tag side of 350 so long time from now I will have these

I think you are getting the message types confused. Highlighted in green below is the "APRS Beacon" with position information (no statistics here) which is sent at the Beacon

When APRSISCE/32 is configured as an IGate (both an APRS-IS port and an RF port), the Lynn (D) - KJ4ERJ - Author of APRSISCE for Windows Mobile and Win32

Greetings, To delete the memory items: 1 Click Menu 2 Click My Locations 3 Click Delete All in lower right corner. It will take several seconds to complete this task. Hope this helps. Kjell KD0BXJ

Hi! The below are my station statistics which are sent at 1 hour intervals and found in the aprs.fi raw packets (fine, no issues): APWW10,TCPIP*,qAC,T2SWEDEN2:@162054h3043.84N/07647.85E-Hi de Baba!

Had an issue like this on a Nuvi 1490 a while ago. Once you have the nuvi connected, look for a recycle folder on the nuvi. You might need to open a command prompt to clear it. Good luck

My Nuvi350 displays "full memory" which some time ago I was able to clear. Now I get this popup which now I cannot figure how to stop it. There is no SD card plugged into the unit (I cannot remember

Lynn just confirmed, your beacon path is what is used for the message. You just stated your beacon path is WIDE2-1, so you don't need to add anything else in the message box. You message will be

All transmissions by APRSISCE/32 use the beacon path. This includes messages being sent via RF. APRSISCE/32 does not currently allow custom path specifications for message QSOs.

Hi Robert, Tnx for the reply. I should have clarified, it's the path parameters that has me confused. Lets say the local wide-are coverage digi is alias "UTICA". I want to send a message to KB2QXA