Date   

Re: How Do I Connect to an IC-9700 Through my PC?

Rob Giuliano
 

APRSIS32 does not directly create a "soundcard TNC" device to actually decode the tones from teh radio and turn them into packets.
You will need an intermediate computer application to handle that function.  Some options are: DireWolf, AGWpe, UZ7OH, or some of the multimode decoders will decode packet as well.

Assuming you run the soundcard TNC application on the same computer, these settings will allow that soundcard TNC data exchange with APRSIS32.

Robert Giuliano
KB8RCO



On Wednesday, June 24, 2020, 8:27:41 AM EDT, hl9gy.korea@... <hl9gy.korea@...> wrote:


I did a search in this group for "IC-9700" and got zero hits!  Anyway, I'm trying to connect to my IC-9700 through my PC sound card.  In Ports, I create a new AGW port, I select TCP/IP, I enter in the IP box 127.0.0.1, and 8000 in the Port box.  Then OK and accept.  Nothing.  Can anyone inform me or point me to an info source that guides me through setup with an IC-9700?  Not using GPS.


How Do I Connect to an IC-9700 Through my PC?

hl9gy.korea@...
 

I did a search in this group for "IC-9700" and got zero hits!  Anyway, I'm trying to connect to my IC-9700 through my PC sound card.  In Ports, I create a new AGW port, I select TCP/IP, I enter in the IP box 127.0.0.1, and 8000 in the Port box.  Then OK and accept.  Nothing.  Can anyone inform me or point me to an info source that guides me through setup with an IC-9700?  Not using GPS.


Re: [EXT] Re: [APRSISCE] Configure APRSIS32 for Kenwood TM-D710GA as Mobile

Lynn Deffenbaugh
 

Well, I don't have access to a D710, so I can test or verify those statements.  IIRC, the bulk of that Wiki page was copied from an e-mail discussion on the list.

Maybe someone that is using a D710 in APRS mode with APRSISCE/32 can provide insight into their experience?

Lynn (D) - KJ4ERJ - Author of APRSISCE for Windows Mobile and Win32

On 6/23/2020 8:29 PM, Charles Jessee wrote:

Hi Lynn - I did. What has me wondering is the stuff at the bottom:

 How can you configure APRSISCE/32 to run in APRS mode without usurping control from the Kenwood TM-D710 radio? Well, you really can't if you expect APRSISCE/32 to ever transmit because on the first transmission, MYCALL will be set which changes the D710's identity until it's next TNC reset. However, if you avoid messaging from APRSISCE/32 (or even receiving a message to which an ack must be sent), the following might work for you.”

Messages Checked - If you want messaging to work on APRSISCE/32 (See warning above)“

The way I’m reading it, is check Messages is you want messaging to work, which should work as long as you don’t message or receive one to which an ack must be sent. So if I check messaging I should never message? And I’m not quite sure about messages where an ack *must*be sent. 


Thanks for you patience have my questions - APRSIS32 is super-duper fine stuff and I appreciate your efforts!


Bret/N4SRN


Re: [EXT] Re: [APRSISCE] Configure APRSIS32 for Kenwood TM-D710GA as Mobile

Charles Jessee
 

Hi Lynn - I did. What has me wondering is the stuff at the bottom:

 How can you configure APRSISCE/32 to run in APRS mode without usurping control from the Kenwood TM-D710 radio? Well, you really can't if you expect APRSISCE/32 to ever transmit because on the first transmission, MYCALL will be set which changes the D710's identity until it's next TNC reset. However, if you avoid messaging from APRSISCE/32 (or even receiving a message to which an ack must be sent), the following might work for you.”

Messages Checked - If you want messaging to work on APRSISCE/32 (See warning above)“

The way I’m reading it, is check Messages is you want messaging to work, which should work as long as you don’t message or receive one to which an ack must be sent. So if I check messaging I should never message? And I’m not quite sure about messages where an ack *must*be sent. 


Thanks for you patience have my questions - APRSIS32 is super-duper fine stuff and I appreciate your efforts!


Bret/N4SRN


Re: [EXT] Re: [APRSISCE] Configure APRSIS32 for Kenwood TM-D710GA as Mobile

Lynn Deffenbaugh
 

Have you read the following page on the Wiki?

http://aprsisce.wikidot.com/port:kenwood-tm-d710

Lynn (D) - KJ4ERJ - Author of APRSISCE for Windows Mobile and Win32

On 6/23/2020 3:57 PM, Charles Jessee wrote:
Hi Lynn - I tried this to create the KWD710(APRS) and KWD710(PKT) ports on APRSISCE and am running it on the APRS port now.
https://s3-us-west-1.amazonaws.com/groupsioattachments/13949/33145978/13259/0?AWSAccessKeyId=AKIAJECNKOVMCCU3ATNQ&Expires=1592933888&Signature=F%2Bi18GpC0tZ6vgSvV3xje48u7WI%3D&response-content-disposition=inline%3B+filename%3D%22D710+APRSIS32+Set+up+full.pdf%22
What are the advantages/disadvantages of this configuration?
BRET/N4SRN


Re: [EXT] Re: [APRSISCE] Configure APRSIS32 for Kenwood TM-D710GA as Mobile

Charles Jessee
 

Hi Lynn - I tried this to create the KWD710(APRS) and KWD710(PKT) ports on APRSISCE and am running it on the APRS port now.
https://s3-us-west-1.amazonaws.com/groupsioattachments/13949/33145978/13259/0?AWSAccessKeyId=AKIAJECNKOVMCCU3ATNQ&Expires=1592933888&Signature=F%2Bi18GpC0tZ6vgSvV3xje48u7WI%3D&response-content-disposition=inline%3B+filename%3D%22D710+APRSIS32+Set+up+full.pdf%22
What are the advantages/disadvantages of this configuration?
BRET/N4SRN


Re: [EXT] Re: [APRSISCE] Configure APRSIS32 for Kenwood TM-D710GA as Mobile

Lynn Deffenbaugh
 

And what port type are you using in APRSIS32 for your D710?  It it KISS or APRS?

Lynn (D) - KJ4ERJ - Author of APRSISCE for Windows Mobile and Win32

On 6/21/2020 7:31 PM, Gary via groups.io wrote:
Yes, I use my D710G all the time for APRSIS32 and Winlink.  Keep my cable in all the time and just bring my laptop and plug in.
73 de Gary N6GLS 



Sent from my T-Mobile 4G LTE Device


-------- Original message --------
From: Kevin Reeve <kevin.reeve@...>
Date: 6/21/20 4:13 PM (GMT-08:00)
Subject: Re: [EXT] Re: [APRSISCE] Configure APRSIS32 for Kenwood TM-D710GA as Mobile

  1. Basically your putting the D710G in kiss mode, meaning the model is dumb and APRSIS32 is doing all the work, encode and decode.  The advantage you get with the D710G is that you can actually use the modem in the radio and access it. For example you can do winlink with it, without any other TNC in packet mode on the D710.  You can not access the TNC in the FTM-400 or any Yaesu radios other than to get data out of the radio.

Kevin

N7RXE

 

 

From: <APRSISCE@groups.io> on behalf of "Charles Jessee via groups.io" <cbjesseeNH@...>
Reply-To: "APRSISCE@groups.io" <APRSISCE@groups.io>
Date: Sunday, June 21, 2020 at 4:05 PM
To: "APRSISCE@groups.io" <APRSISCE@groups.io>
Subject: [EXT] Re: [APRSISCE] Configure APRSIS32 for Kenwood TM-D710GA as Mobile

 

I’m just looking to switch from a Yaesu FTM-400 to a Kenwood TM-D7100GA and looking at the Wiki: “ How can you configure APRSISCE/32 to run in APRS mode without usurping control from the Kenwood TM-D710 radio? Well, you really can't if you expect APRSISCE/32 to ever transmit because on the first transmission, MYCALL will be set which changes the D710's identity until it's next TNC reset. However, if you avoid messaging from APRSISCE/32 (or even receiving a message to which an ack must be sent), the following might work for you.“


This seems to suggest that if one gives up major functionality APRSIS32 can work with a TM-710GA. What’s the upside for accepting this downside? If sure I’m missing something...

Bret/N4SRN

CAUTION: This email originated from outside of USU. If this appears to be a USU employee, beware of impersonators. Do not click links, reply, download images, or open attachments unless you verify the sender’s identity and know the content is safe.

 


Re: [EXT] Re: [APRSISCE] Configure APRSIS32 for Kenwood TM-D710GA as Mobile

Gary 2200E N6GLS
 

Yes, I use my D710G all the time for APRSIS32 and Winlink.  Keep my cable in all the time and just bring my laptop and plug in.
73 de Gary N6GLS 



Sent from my T-Mobile 4G LTE Device


-------- Original message --------
From: Kevin Reeve <kevin.reeve@...>
Date: 6/21/20 4:13 PM (GMT-08:00)
To: APRSISCE@groups.io
Subject: Re: [EXT] Re: [APRSISCE] Configure APRSIS32 for Kenwood TM-D710GA as Mobile

  1. Basically your putting the D710G in kiss mode, meaning the model is dumb and APRSIS32 is doing all the work, encode and decode.  The advantage you get with the D710G is that you can actually use the modem in the radio and access it. For example you can do winlink with it, without any other TNC in packet mode on the D710.  You can not access the TNC in the FTM-400 or any Yaesu radios other than to get data out of the radio.

Kevin

N7RXE

 

 

From: <APRSISCE@groups.io> on behalf of "Charles Jessee via groups.io" <cbjesseeNH@...>
Reply-To: "APRSISCE@groups.io" <APRSISCE@groups.io>
Date: Sunday, June 21, 2020 at 4:05 PM
To: "APRSISCE@groups.io" <APRSISCE@groups.io>
Subject: [EXT] Re: [APRSISCE] Configure APRSIS32 for Kenwood TM-D710GA as Mobile

 

I’m just looking to switch from a Yaesu FTM-400 to a Kenwood TM-D7100GA and looking at the Wiki: “ How can you configure APRSISCE/32 to run in APRS mode without usurping control from the Kenwood TM-D710 radio? Well, you really can't if you expect APRSISCE/32 to ever transmit because on the first transmission, MYCALL will be set which changes the D710's identity until it's next TNC reset. However, if you avoid messaging from APRSISCE/32 (or even receiving a message to which an ack must be sent), the following might work for you.“


This seems to suggest that if one gives up major functionality APRSIS32 can work with a TM-710GA. What’s the upside for accepting this downside? If sure I’m missing something...

Bret/N4SRN

CAUTION: This email originated from outside of USU. If this appears to be a USU employee, beware of impersonators. Do not click links, reply, download images, or open attachments unless you verify the sender’s identity and know the content is safe.

 


Re: [EXT] Re: [APRSISCE] Configure APRSIS32 for Kenwood TM-D710GA as Mobile

Kevin Reeve
 

  1. Basically your putting the D710G in kiss mode, meaning the model is dumb and APRSIS32 is doing all the work, encode and decode.  The advantage you get with the D710G is that you can actually use the modem in the radio and access it. For example you can do winlink with it, without any other TNC in packet mode on the D710.  You can not access the TNC in the FTM-400 or any Yaesu radios other than to get data out of the radio.

Kevin

N7RXE

 

 

From: <APRSISCE@groups.io> on behalf of "Charles Jessee via groups.io" <cbjesseeNH@...>
Reply-To: "APRSISCE@groups.io" <APRSISCE@groups.io>
Date: Sunday, June 21, 2020 at 4:05 PM
To: "APRSISCE@groups.io" <APRSISCE@groups.io>
Subject: [EXT] Re: [APRSISCE] Configure APRSIS32 for Kenwood TM-D710GA as Mobile

 

I’m just looking to switch from a Yaesu FTM-400 to a Kenwood TM-D7100GA and looking at the Wiki: “ How can you configure APRSISCE/32 to run in APRS mode without usurping control from the Kenwood TM-D710 radio? Well, you really can't if you expect APRSISCE/32 to ever transmit because on the first transmission, MYCALL will be set which changes the D710's identity until it's next TNC reset. However, if you avoid messaging from APRSISCE/32 (or even receiving a message to which an ack must be sent), the following might work for you.“


This seems to suggest that if one gives up major functionality APRSIS32 can work with a TM-710GA. What’s the upside for accepting this downside? If sure I’m missing something...

Bret/N4SRN

CAUTION: This email originated from outside of USU. If this appears to be a USU employee, beware of impersonators. Do not click links, reply, download images, or open attachments unless you verify the sender’s identity and know the content is safe.

 


Re: Configure APRSIS32 for Kenwood TM-D710GA as Mobile

Charles Jessee
 

I’m just looking to switch from a Yaesu FTM-400 to a Kenwood TM-D7100GA and looking at the Wiki: “ How can you configure APRSISCE/32 to run in APRS mode without usurping control from the Kenwood TM-D710 radio? Well, you really can't if you expect APRSISCE/32 to ever transmit because on the first transmission, MYCALL will be set which changes the D710's identity until it's next TNC reset. However, if you avoid messaging from APRSISCE/32 (or even receiving a message to which an ack must be sent), the following might work for you.“

This seems to suggest that if one gives up major functionality APRSIS32 can work with a TM-710GA. What’s the upside for accepting this downside? If sure I’m missing something...

Bret/N4SRN


Re: Igates and their use of digi paths

Greg Depew
 

See below, again


From: APRSISCE@groups.io <APRSISCE@groups.io> on behalf of James Ewen <ve6srv@...>
Sent: Sunday, June 21, 2020 1:35 PM
To: APRSISCE@groups.io <APRSISCE@groups.io>
Subject: Re: [APRSISCE] Igates and their use of digi paths
 
Greg,

There’s a way to make things happen. You just go out and do it. 

Back in the late 90’s I wanted to get into APRS. I talked to a few buddies about it, and we all thought it would be interesting. But there was no APRS digipeaters around. The closest digi was 200 miles to the south. 

So I grabbed my old Kantronics KAM, figured out how to format a position packet (with much assistance from VE6SZR) and programmed that position packet into my beacon slot, and set the KAM to beacon every three minutes. Boom! First APRS station on the air in the Edmonton area. 

A couple days later VE6BCA configured his KPC-3 to act as a digi. Boom! First digi in Edmonton. It was just at a house on a 30 foot mast, but it was on the air, and my packets were being digipeated. 

Sometimes you just have to do it yourself. All of the digipeaters in Northern Alberta have been put in place by individuals. No club affiliation or support for just about all of them. Sometimes it is just easier to stay away from the politics that clubs can create and just get after it.  

So, if you have a station at your house, you could set it up as a digipeater. If it’s the only digipeater in the area, set it up as a full digi. If you have internet access and can do so, tie it into your digi and make it an I-gate as well. 

I do have a home station and its setup as a wide 2 digi and I-gate, and has been for about 10 years now. 

If at some point you can get a better spot and equipment, install a digi where it has advantageous coverage of your area. 

If people complain that “Nobody is doing anything around here.”, that means they are also part of the nobody. 

​Unfortunately there really is nobody to complain! Just me! 😄

This really isn’t directly aimed at you Greg, but more of a generic discussion for anyone in a similar situation. You’ve just spurred me into responding. I’m not trying to call you out or anything. 

​Not feeling called out, just pointing out in my previous messages that I am the only one with interest around here other than the other 2 one of which has no interest in building out the network, just using his deaf tracker for events outside of our area that actually has network coverage. Ironic right?

The other fellow I mentioned is working slowing at getting some network stuff going as I said before about getting it up on his local water tower. As long as his install meets his expectations, I believe he's going to invest more into getting more digis up in the area.  He's setting up one of the Tiny Trak Ready to Go boxes on the tower and its going to strictly solar powered. As long as everything goes right I may be able to convince him and our club to put one on our northern most repeater. 

At some point if you realize you need to take the initiative, that group of “nobody”s looses a member, and things start to happen in your area. 

​Hence why I was trying to get my mobile fill-in to send the messages back!

It can be a fair bit of work to start making things happen. It helps if you can find a couple people with a similar mindset. 

I was lucky to have a couple buddies that I could convince to join me on my projects. 

We started and built out the local APRS network. We built half a dozen HamHUDs so we could have mobile stations before Kenwood even thought of making the D700. We built payloads and launched dozens of high altitude balloons. 

I also agitate and get people working on other projects in other hobbies that I participate in. I do all of that because I’m selfish. I want to be able to play with stuff and have things that weren't here before. 

It can be difficult, if not impossible to do it alone, so find at least one other person that shares your interest, cultivate a friendship, and get after it. 

Nobody is going to do it unless somebody takes the initiative. 

Be a somebody, not a nobody. 

This now concludes my motivational speech for today! 😀

James 
VE6SRV

On Sun, Jun 21, 2020 at 10:56 AM Greg Depew <goatherder_4891@...> wrote:
What I'm saying is there is no network around me except me! That digi 30 miles away sometimes can't get into the network either and may disappear for hours or sometimes days from being on the maps. Unfortunately I don't have the money nor the locations to be able to put up a high level digi like needs to be. For now I'm it. 



Greg KB3KBR Sent from my Verizon, Samsung Galaxy smartphone



-------- Original message --------
From: James Ewen <ve6srv@...>
Date: 6/21/20 02:40 (GMT-05:00)
Subject: Re: [APRSISCE] Igates and their use of digi paths

While true the nearest permanent digi near me is 30 miles away and a mobile can't hit it unless it's about 15 miles away. I can't even reliably get into any of the digis in the area with the home station. 

So what you are describing is an area with no digipeater coverage. This is not a location for a fill-in digipeater, this area needs a full digipeater. 

A station operating in this area will not be able to participate in APRS operations on the digipeater network as there is no digipeater network in the area. A fill-in digipeater acts as a one way booster in the digipeater network. It will only ever act upon the first path element of a packet. If you put a fill-in digipeater into an area that is not covered by a main digipeater, then there is no way for any traffic (position reports, or more importantly messages) to get back into the area. 

Stations should never use WIDE1-1 anywhere other than as the first element in their outgoing path. Anyone wanting to get information back to station that only has a fill-in digipeater within range from an area 2 digits away would be forced to use WIDE1–1 As a second path element, which we all know is a very bad thing to do. 

Build the network properly and APRS works great. Build it incorrectly and you can have something that is a waste of time, effort, money, and just generally makes people resort to trying stupid things that cause more problems for everyone. 

James 
VE6SRV


On Sat, Jun 20, 2020 at 10:12 PM Greg Depew <goatherder_4891@...> wrote:
See below



Greg KB3KBR Sent from my Verizon, Samsung Galaxy smartphone


-------- Original message --------
From: James Ewen <ve6srv@...>
Date: 6/20/20 20:06 (GMT-05:00)
Subject: Re: [APRSISCE] Igates and their use of digi paths

A WIDE1-1 digipeater should be a located in an area where the main digipeaters can be heard and copied, but low powered handheld stations can’t get the attention of the main digipeater. A WIDE1-1 digipeater fills in and helps the low powered handheld stations get that first hop into the digipeater network. 

Agree wholeheartedly.

High powered (5 watts or more) mobile stations and fixed stations should never use an outgoing path of WIDE1-1. Digipeaters should be located at sites that provide advantageous coverage of the local area. A digipeater should NEVER EVER use WIDE1-1 as an outgoing path. If a digipeater is located such that it requires help from a home fill-in digipeater to be heard by the main digipeaters, it should shut down and removed from service. It is causing more congestion of the local network than it is helping. 

While true the nearest permanent digi near me is 30 miles away and a mobile can't hit it unless it's about 15 miles away. I can't even reliably get into any of the digis in the area with the home station. The network around here is almost non existent. My goal (which was solved with Lynn's advice of setting the gate to Wide1-1 to make the fill in pass the traffic back) was to use the fill in mobile in areas where I know the handheld can't get out. I used it in such a way tonight on our local lake using the handheld on the kayak to go back to mobile fill in and get back to the main digigate at my house. Successfully was able to send and receive messages to Wxbot and SMSGATE. 

If there are any other fill ins that my main digigate lights up I don't know where they are. Other than myself, theres only 2 other people running APRS in my county. One is using a deaf tracker and the other is in the process of getting a solar digi setup on his towns water tower which should increase the coverage to most of the southern part of the county. 

Unfortunately my local club has zero interest in APRS and when I approached our repeater guru about getting stuff on our main tower he shot me down with concerns of it desensing the repeater.  I would love to get high sites but not enough intrest has taken hold even after I held a presentation on it a couple years back. 




On Sat, Jun 20, 2020 at 10:44 AM Greg Depew <goatherder_4891@...> wrote:
Would it be better for me to change 4 to respond to Wide2-2 or have the 1 the igate put out Wide1-1 and maybe light up digis that are very far away? 

Sometimes I can get into a big digi in Ohio but I can't hear it back on anything but the -1, and I've seen my packets be delayed while they hop through the system on open days then get regated about a min later sometimes in Canada or a different place in Ohio. 



Greg KB3KBR Sent from my Verizon, Samsung Galaxy smartphone



-------- Original message --------
From: Lynn Deffenbaugh <kj4erj@...>
Date: 6/19/20 19:48 (GMT-05:00)
Subject: Re: [APRSISCE] Igates and their use of digi paths

On 6/19/2020 6:38 PM, Greg Depew wrote:
Can you give a more complete description of what all is involved?

KB3KBR-11 is what station?  Software, TNC and radio please.

11 is a Yaesu Ft1d

Same for -4 (a WIDE1-1 digi) 

4 is a fill in digi , TinyTrak 4 with GPS and and FT 8800 in a go box programmed to only respond to Wide1-1 and it's own callsign 

Same for -1 (presumably a WIDE2 digi)

1 is APRSIS32 via sound card Signal link into an Ftm 350and is an igate and digi that responds to Wide1-1 and Wide2-2 

Same for the IGate and please include callsign-SSID with the other 3 pieces of the puzzle.

And some idea of who can copy who directly.  Can -1 copy the IGate directly or does the IGate need the boost from -4 to get to -1?  

1 is the igate, 4 is my mobile fill in that I'm using to get 11 back to the igate 

You've already mentioned that you can't hear -1 indoors, but only -4.  Can you copy the IGate indoors?  

When I'm at work inside our 911 center our grounding halo blocks just about everything. 4 is sitting in the truck in the parking lot and can hear 1 and 11. 11 can only hear 1 if it's out side and its iffy if 1 can hear 11 without either holding the antenna in the or more power.

If not, then can we assume the IGate is actually remote from your QTH, but -1 is local?

So, with that final line, it would seem that if you're IGate is using a WIDE1-1,WIDE2-1 path, then -4 will copy it and repeat it locally so that -11 can copy the response at the 911 center.  Without the WIDE1-1, -4 won't digipeat and -11 won't copy it.

The big issue you have is that the -11 HT can't copy the IGate directly when at the 911 center, and apparently there's no bigger digipeater that will digipeat the IGate and be copied by the -11 HT.  No amount of pathing is going to solve an issue of a marginal receiver (the HT) at some distance from the IGate without strong coverage.

But a WIDE1-1,WIDE2-1 path on the IGate should trigger the -4 digipeater to deliver a stronger packet to the HT.

Anyone have any better suggestion?

Lynn (D) - KJ4ERJ - Author of APRSISCE for Windows Mobile and Win32

PS.  An external antenna that you can connect to the HT inside the 911 center would likely also solve your issue.  Apparently the -4 has bigger ears than the HT or it wouldn't copy the IGate while sitting in the parking lot.

--
James
VE6SRV

--
James
VE6SRV

--
James
VE6SRV

Virus-free. www.avast.com


Re: Igates and their use of digi paths

James Ewen
 

Greg,

There’s a way to make things happen. You just go out and do it. 

Back in the late 90’s I wanted to get into APRS. I talked to a few buddies about it, and we all thought it would be interesting. But there was no APRS digipeaters around. The closest digi was 200 miles to the south. 

So I grabbed my old Kantronics KAM, figured out how to format a position packet (with much assistance from VE6SZR) and programmed that position packet into my beacon slot, and set the KAM to beacon every three minutes. Boom! First APRS station on the air in the Edmonton area. 

A couple days later VE6BCA configured his KPC-3 to act as a digi. Boom! First digi in Edmonton. It was just at a house on a 30 foot mast, but it was on the air, and my packets were being digipeated. 

Sometimes you just have to do it yourself. All of the digipeaters in Northern Alberta have been put in place by individuals. No club affiliation or support for just about all of them. Sometimes it is just easier to stay away from the politics that clubs can create and just get after it.  

So, if you have a station at your house, you could set it up as a digipeater. If it’s the only digipeater in the area, set it up as a full digi. If you have internet access and can do so, tie it into your digi and make it an I-gate as well. 

If at some point you can get a better spot and equipment, install a digi where it has advantageous coverage of your area. 

If people complain that “Nobody is doing anything around here.”, that means they are also part of the nobody. 

This really isn’t directly aimed at you Greg, but more of a generic discussion for anyone in a similar situation. You’ve just spurred me into responding. I’m not trying to call you out or anything. 

At some point if you realize you need to take the initiative, that group of “nobody”s looses a member, and things start to happen in your area. 

It can be a fair bit of work to start making things happen. It helps if you can find a couple people with a similar mindset. 

I was lucky to have a couple buddies that I could convince to join me on my projects. 

We started and built out the local APRS network. We built half a dozen HamHUDs so we could have mobile stations before Kenwood even thought of making the D700. We built payloads and launched dozens of high altitude balloons. 

I also agitate and get people working on other projects in other hobbies that I participate in. I do all of that because I’m selfish. I want to be able to play with stuff and have things that weren't here before. 

It can be difficult, if not impossible to do it alone, so find at least one other person that shares your interest, cultivate a friendship, and get after it. 

Nobody is going to do it unless somebody takes the initiative. 

Be a somebody, not a nobody. 

This now concludes my motivational speech for today! 😀

James 
VE6SRV

On Sun, Jun 21, 2020 at 10:56 AM Greg Depew <goatherder_4891@...> wrote:
What I'm saying is there is no network around me except me! That digi 30 miles away sometimes can't get into the network either and may disappear for hours or sometimes days from being on the maps. Unfortunately I don't have the money nor the locations to be able to put up a high level digi like needs to be. For now I'm it. 



Greg KB3KBR Sent from my Verizon, Samsung Galaxy smartphone



-------- Original message --------
From: James Ewen <ve6srv@...>
Date: 6/21/20 02:40 (GMT-05:00)
Subject: Re: [APRSISCE] Igates and their use of digi paths

While true the nearest permanent digi near me is 30 miles away and a mobile can't hit it unless it's about 15 miles away. I can't even reliably get into any of the digis in the area with the home station. 

So what you are describing is an area with no digipeater coverage. This is not a location for a fill-in digipeater, this area needs a full digipeater. 

A station operating in this area will not be able to participate in APRS operations on the digipeater network as there is no digipeater network in the area. A fill-in digipeater acts as a one way booster in the digipeater network. It will only ever act upon the first path element of a packet. If you put a fill-in digipeater into an area that is not covered by a main digipeater, then there is no way for any traffic (position reports, or more importantly messages) to get back into the area. 

Stations should never use WIDE1-1 anywhere other than as the first element in their outgoing path. Anyone wanting to get information back to station that only has a fill-in digipeater within range from an area 2 digits away would be forced to use WIDE1–1 As a second path element, which we all know is a very bad thing to do. 

Build the network properly and APRS works great. Build it incorrectly and you can have something that is a waste of time, effort, money, and just generally makes people resort to trying stupid things that cause more problems for everyone. 

James 
VE6SRV


On Sat, Jun 20, 2020 at 10:12 PM Greg Depew <goatherder_4891@...> wrote:
See below



Greg KB3KBR Sent from my Verizon, Samsung Galaxy smartphone


-------- Original message --------
From: James Ewen <ve6srv@...>
Date: 6/20/20 20:06 (GMT-05:00)
Subject: Re: [APRSISCE] Igates and their use of digi paths

A WIDE1-1 digipeater should be a located in an area where the main digipeaters can be heard and copied, but low powered handheld stations can’t get the attention of the main digipeater. A WIDE1-1 digipeater fills in and helps the low powered handheld stations get that first hop into the digipeater network. 

Agree wholeheartedly.

High powered (5 watts or more) mobile stations and fixed stations should never use an outgoing path of WIDE1-1. Digipeaters should be located at sites that provide advantageous coverage of the local area. A digipeater should NEVER EVER use WIDE1-1 as an outgoing path. If a digipeater is located such that it requires help from a home fill-in digipeater to be heard by the main digipeaters, it should shut down and removed from service. It is causing more congestion of the local network than it is helping. 

While true the nearest permanent digi near me is 30 miles away and a mobile can't hit it unless it's about 15 miles away. I can't even reliably get into any of the digis in the area with the home station. The network around here is almost non existent. My goal (which was solved with Lynn's advice of setting the gate to Wide1-1 to make the fill in pass the traffic back) was to use the fill in mobile in areas where I know the handheld can't get out. I used it in such a way tonight on our local lake using the handheld on the kayak to go back to mobile fill in and get back to the main digigate at my house. Successfully was able to send and receive messages to Wxbot and SMSGATE. 

If there are any other fill ins that my main digigate lights up I don't know where they are. Other than myself, theres only 2 other people running APRS in my county. One is using a deaf tracker and the other is in the process of getting a solar digi setup on his towns water tower which should increase the coverage to most of the southern part of the county. 

Unfortunately my local club has zero interest in APRS and when I approached our repeater guru about getting stuff on our main tower he shot me down with concerns of it desensing the repeater.  I would love to get high sites but not enough intrest has taken hold even after I held a presentation on it a couple years back. 




On Sat, Jun 20, 2020 at 10:44 AM Greg Depew <goatherder_4891@...> wrote:
Would it be better for me to change 4 to respond to Wide2-2 or have the 1 the igate put out Wide1-1 and maybe light up digis that are very far away? 

Sometimes I can get into a big digi in Ohio but I can't hear it back on anything but the -1, and I've seen my packets be delayed while they hop through the system on open days then get regated about a min later sometimes in Canada or a different place in Ohio. 



Greg KB3KBR Sent from my Verizon, Samsung Galaxy smartphone



-------- Original message --------
From: Lynn Deffenbaugh <kj4erj@...>
Date: 6/19/20 19:48 (GMT-05:00)
Subject: Re: [APRSISCE] Igates and their use of digi paths

On 6/19/2020 6:38 PM, Greg Depew wrote:
Can you give a more complete description of what all is involved?

KB3KBR-11 is what station?  Software, TNC and radio please.

11 is a Yaesu Ft1d

Same for -4 (a WIDE1-1 digi) 

4 is a fill in digi , TinyTrak 4 with GPS and and FT 8800 in a go box programmed to only respond to Wide1-1 and it's own callsign 

Same for -1 (presumably a WIDE2 digi)

1 is APRSIS32 via sound card Signal link into an Ftm 350and is an igate and digi that responds to Wide1-1 and Wide2-2 

Same for the IGate and please include callsign-SSID with the other 3 pieces of the puzzle.

And some idea of who can copy who directly.  Can -1 copy the IGate directly or does the IGate need the boost from -4 to get to -1?  

1 is the igate, 4 is my mobile fill in that I'm using to get 11 back to the igate 

You've already mentioned that you can't hear -1 indoors, but only -4.  Can you copy the IGate indoors?  

When I'm at work inside our 911 center our grounding halo blocks just about everything. 4 is sitting in the truck in the parking lot and can hear 1 and 11. 11 can only hear 1 if it's out side and its iffy if 1 can hear 11 without either holding the antenna in the or more power.

If not, then can we assume the IGate is actually remote from your QTH, but -1 is local?

So, with that final line, it would seem that if you're IGate is using a WIDE1-1,WIDE2-1 path, then -4 will copy it and repeat it locally so that -11 can copy the response at the 911 center.  Without the WIDE1-1, -4 won't digipeat and -11 won't copy it.

The big issue you have is that the -11 HT can't copy the IGate directly when at the 911 center, and apparently there's no bigger digipeater that will digipeat the IGate and be copied by the -11 HT.  No amount of pathing is going to solve an issue of a marginal receiver (the HT) at some distance from the IGate without strong coverage.

But a WIDE1-1,WIDE2-1 path on the IGate should trigger the -4 digipeater to deliver a stronger packet to the HT.

Anyone have any better suggestion?

Lynn (D) - KJ4ERJ - Author of APRSISCE for Windows Mobile and Win32

PS.  An external antenna that you can connect to the HT inside the 911 center would likely also solve your issue.  Apparently the -4 has bigger ears than the HT or it wouldn't copy the IGate while sitting in the parking lot.

--
James
VE6SRV

--
James
VE6SRV

--
James
VE6SRV


Re: Igates and their use of digi paths

Glenn O'Connor
 

Use APRSDroid, to self-report.

 

From: APRSISCE@groups.io <APRSISCE@groups.io> On Behalf Of Greg Depew
Sent: Sunday, June 21, 2020 11:56 AM
To: APRSISCE@groups.io
Subject: Re: [APRSISCE] Igates and their use of digi paths

 

What I'm saying is there is no network around me except me! That digi 30 miles away sometimes can't get into the network either and may disappear for hours or sometimes days from being on the maps. Unfortunately I don't have the money nor the locations to be able to put up a high level digi like needs to be. For now I'm it. 

 

 

 

Greg KB3KBR Sent from my Verizon, Samsung Galaxy smartphone

 

 

 

-------- Original message --------

From: James Ewen <ve6srv@...>

Date: 6/21/20 02:40 (GMT-05:00)

Subject: Re: [APRSISCE] Igates and their use of digi paths

 

While true the nearest permanent digi near me is 30 miles away and a mobile can't hit it unless it's about 15 miles away. I can't even reliably get into any of the digis in the area with the home station. 

 

So what you are describing is an area with no digipeater coverage. This is not a location for a fill-in digipeater, this area needs a full digipeater. 

 

A station operating in this area will not be able to participate in APRS operations on the digipeater network as there is no digipeater network in the area. A fill-in digipeater acts as a one way booster in the digipeater network. It will only ever act upon the first path element of a packet. If you put a fill-in digipeater into an area that is not covered by a main digipeater, then there is no way for any traffic (position reports, or more importantly messages) to get back into the area. 

 

Stations should never use WIDE1-1 anywhere other than as the first element in their outgoing path. Anyone wanting to get information back to station that only has a fill-in digipeater within range from an area 2 digits away would be forced to use WIDE1–1 As a second path element, which we all know is a very bad thing to do. 

 

Build the network properly and APRS works great. Build it incorrectly and you can have something that is a waste of time, effort, money, and just generally makes people resort to trying stupid things that cause more problems for everyone. 

 

James 

VE6SRV

 

 

On Sat, Jun 20, 2020 at 10:12 PM Greg Depew <goatherder_4891@...> wrote:

See below

 

 

 

Greg KB3KBR Sent from my Verizon, Samsung Galaxy smartphone

 

 

-------- Original message --------

From: James Ewen <ve6srv@...>

Date: 6/20/20 20:06 (GMT-05:00)

Subject: Re: [APRSISCE] Igates and their use of digi paths

 

A WIDE1-1 digipeater should be a located in an area where the main digipeaters can be heard and copied, but low powered handheld stations can’t get the attention of the main digipeater. A WIDE1-1 digipeater fills in and helps the low powered handheld stations get that first hop into the digipeater network. 

 

Agree wholeheartedly.

 

High powered (5 watts or more) mobile stations and fixed stations should never use an outgoing path of WIDE1-1. Digipeaters should be located at sites that provide advantageous coverage of the local area. A digipeater should NEVER EVER use WIDE1-1 as an outgoing path. If a digipeater is located such that it requires help from a home fill-in digipeater to be heard by the main digipeaters, it should shut down and removed from service. It is causing more congestion of the local network than it is helping. 

 

While true the nearest permanent digi near me is 30 miles away and a mobile can't hit it unless it's about 15 miles away. I can't even reliably get into any of the digis in the area with the home station. The network around here is almost non existent. My goal (which was solved with Lynn's advice of setting the gate to Wide1-1 to make the fill in pass the traffic back) was to use the fill in mobile in areas where I know the handheld can't get out. I used it in such a way tonight on our local lake using the handheld on the kayak to go back to mobile fill in and get back to the main digigate at my house. Successfully was able to send and receive messages to Wxbot and SMSGATE. 

 

If there are any other fill ins that my main digigate lights up I don't know where they are. Other than myself, theres only 2 other people running APRS in my county. One is using a deaf tracker and the other is in the process of getting a solar digi setup on his towns water tower which should increase the coverage to most of the southern part of the county. 

 

Unfortunately my local club has zero interest in APRS and when I approached our repeater guru about getting stuff on our main tower he shot me down with concerns of it desensing the repeater.  I would love to get high sites but not enough intrest has taken hold even after I held a presentation on it a couple years back. 

 

 

 

 

On Sat, Jun 20, 2020 at 10:44 AM Greg Depew <goatherder_4891@...> wrote:

Would it be better for me to change 4 to respond to Wide2-2 or have the 1 the igate put out Wide1-1 and maybe light up digis that are very far away? 

 

Sometimes I can get into a big digi in Ohio but I can't hear it back on anything but the -1, and I've seen my packets be delayed while they hop through the system on open days then get regated about a min later sometimes in Canada or a different place in Ohio. 

 

 

 

Greg KB3KBR Sent from my Verizon, Samsung Galaxy smartphone

 

 

 

-------- Original message --------

From: Lynn Deffenbaugh <kj4erj@...>

Date: 6/19/20 19:48 (GMT-05:00)

Subject: Re: [APRSISCE] Igates and their use of digi paths

 

On 6/19/2020 6:38 PM, Greg Depew wrote:

Can you give a more complete description of what all is involved?

KB3KBR-11 is what station?  Software, TNC and radio please.

11 is a Yaesu Ft1d

Same for -4 (a WIDE1-1 digi) 

4 is a fill in digi , TinyTrak 4 with GPS and and FT 8800 in a go box programmed to only respond to Wide1-1 and it's own callsign 

Same for -1 (presumably a WIDE2 digi)

1 is APRSIS32 via sound card Signal link into an Ftm 350and is an igate and digi that responds to Wide1-1 and Wide2-2 

Same for the IGate and please include callsign-SSID with the other 3 pieces of the puzzle.

And some idea of who can copy who directly.  Can -1 copy the IGate directly or does the IGate need the boost from -4 to get to -1?  

1 is the igate, 4 is my mobile fill in that I'm using to get 11 back to the igate 

You've already mentioned that you can't hear -1 indoors, but only -4.  Can you copy the IGate indoors?  

When I'm at work inside our 911 center our grounding halo blocks just about everything. 4 is sitting in the truck in the parking lot and can hear 1 and 11. 11 can only hear 1 if it's out side and its iffy if 1 can hear 11 without either holding the antenna in the or more power.

If not, then can we assume the IGate is actually remote from your QTH, but -1 is local?

So, with that final line, it would seem that if you're IGate is using a WIDE1-1,WIDE2-1 path, then -4 will copy it and repeat it locally so that -11 can copy the response at the 911 center.  Without the WIDE1-1, -4 won't digipeat and -11 won't copy it.

The big issue you have is that the -11 HT can't copy the IGate directly when at the 911 center, and apparently there's no bigger digipeater that will digipeat the IGate and be copied by the -11 HT.  No amount of pathing is going to solve an issue of a marginal receiver (the HT) at some distance from the IGate without strong coverage.

But a WIDE1-1,WIDE2-1 path on the IGate should trigger the -4 digipeater to deliver a stronger packet to the HT.

Anyone have any better suggestion?

Lynn (D) - KJ4ERJ - Author of APRSISCE for Windows Mobile and Win32

PS.  An external antenna that you can connect to the HT inside the 911 center would likely also solve your issue.  Apparently the -4 has bigger ears than the HT or it wouldn't copy the IGate while sitting in the parking lot.

--

James
VE6SRV

--

James
VE6SRV


Re: Igates and their use of digi paths

Greg Depew
 

What I'm saying is there is no network around me except me! That digi 30 miles away sometimes can't get into the network either and may disappear for hours or sometimes days from being on the maps. Unfortunately I don't have the money nor the locations to be able to put up a high level digi like needs to be. For now I'm it. 



Greg KB3KBR Sent from my Verizon, Samsung Galaxy smartphone



-------- Original message --------
From: James Ewen <ve6srv@...>
Date: 6/21/20 02:40 (GMT-05:00)
To: APRSISCE@groups.io
Subject: Re: [APRSISCE] Igates and their use of digi paths

While true the nearest permanent digi near me is 30 miles away and a mobile can't hit it unless it's about 15 miles away. I can't even reliably get into any of the digis in the area with the home station. 

So what you are describing is an area with no digipeater coverage. This is not a location for a fill-in digipeater, this area needs a full digipeater. 

A station operating in this area will not be able to participate in APRS operations on the digipeater network as there is no digipeater network in the area. A fill-in digipeater acts as a one way booster in the digipeater network. It will only ever act upon the first path element of a packet. If you put a fill-in digipeater into an area that is not covered by a main digipeater, then there is no way for any traffic (position reports, or more importantly messages) to get back into the area. 

Stations should never use WIDE1-1 anywhere other than as the first element in their outgoing path. Anyone wanting to get information back to station that only has a fill-in digipeater within range from an area 2 digits away would be forced to use WIDE1–1 As a second path element, which we all know is a very bad thing to do. 

Build the network properly and APRS works great. Build it incorrectly and you can have something that is a waste of time, effort, money, and just generally makes people resort to trying stupid things that cause more problems for everyone. 

James 
VE6SRV


On Sat, Jun 20, 2020 at 10:12 PM Greg Depew <goatherder_4891@...> wrote:
See below



Greg KB3KBR Sent from my Verizon, Samsung Galaxy smartphone


-------- Original message --------
From: James Ewen <ve6srv@...>
Date: 6/20/20 20:06 (GMT-05:00)
Subject: Re: [APRSISCE] Igates and their use of digi paths

A WIDE1-1 digipeater should be a located in an area where the main digipeaters can be heard and copied, but low powered handheld stations can’t get the attention of the main digipeater. A WIDE1-1 digipeater fills in and helps the low powered handheld stations get that first hop into the digipeater network. 

Agree wholeheartedly.

High powered (5 watts or more) mobile stations and fixed stations should never use an outgoing path of WIDE1-1. Digipeaters should be located at sites that provide advantageous coverage of the local area. A digipeater should NEVER EVER use WIDE1-1 as an outgoing path. If a digipeater is located such that it requires help from a home fill-in digipeater to be heard by the main digipeaters, it should shut down and removed from service. It is causing more congestion of the local network than it is helping. 

While true the nearest permanent digi near me is 30 miles away and a mobile can't hit it unless it's about 15 miles away. I can't even reliably get into any of the digis in the area with the home station. The network around here is almost non existent. My goal (which was solved with Lynn's advice of setting the gate to Wide1-1 to make the fill in pass the traffic back) was to use the fill in mobile in areas where I know the handheld can't get out. I used it in such a way tonight on our local lake using the handheld on the kayak to go back to mobile fill in and get back to the main digigate at my house. Successfully was able to send and receive messages to Wxbot and SMSGATE. 

If there are any other fill ins that my main digigate lights up I don't know where they are. Other than myself, theres only 2 other people running APRS in my county. One is using a deaf tracker and the other is in the process of getting a solar digi setup on his towns water tower which should increase the coverage to most of the southern part of the county. 

Unfortunately my local club has zero interest in APRS and when I approached our repeater guru about getting stuff on our main tower he shot me down with concerns of it desensing the repeater.  I would love to get high sites but not enough intrest has taken hold even after I held a presentation on it a couple years back. 




On Sat, Jun 20, 2020 at 10:44 AM Greg Depew <goatherder_4891@...> wrote:
Would it be better for me to change 4 to respond to Wide2-2 or have the 1 the igate put out Wide1-1 and maybe light up digis that are very far away? 

Sometimes I can get into a big digi in Ohio but I can't hear it back on anything but the -1, and I've seen my packets be delayed while they hop through the system on open days then get regated about a min later sometimes in Canada or a different place in Ohio. 



Greg KB3KBR Sent from my Verizon, Samsung Galaxy smartphone



-------- Original message --------
From: Lynn Deffenbaugh <kj4erj@...>
Date: 6/19/20 19:48 (GMT-05:00)
Subject: Re: [APRSISCE] Igates and their use of digi paths

On 6/19/2020 6:38 PM, Greg Depew wrote:
Can you give a more complete description of what all is involved?

KB3KBR-11 is what station?  Software, TNC and radio please.

11 is a Yaesu Ft1d

Same for -4 (a WIDE1-1 digi) 

4 is a fill in digi , TinyTrak 4 with GPS and and FT 8800 in a go box programmed to only respond to Wide1-1 and it's own callsign 

Same for -1 (presumably a WIDE2 digi)

1 is APRSIS32 via sound card Signal link into an Ftm 350and is an igate and digi that responds to Wide1-1 and Wide2-2 

Same for the IGate and please include callsign-SSID with the other 3 pieces of the puzzle.

And some idea of who can copy who directly.  Can -1 copy the IGate directly or does the IGate need the boost from -4 to get to -1?  

1 is the igate, 4 is my mobile fill in that I'm using to get 11 back to the igate 

You've already mentioned that you can't hear -1 indoors, but only -4.  Can you copy the IGate indoors?  

When I'm at work inside our 911 center our grounding halo blocks just about everything. 4 is sitting in the truck in the parking lot and can hear 1 and 11. 11 can only hear 1 if it's out side and its iffy if 1 can hear 11 without either holding the antenna in the or more power.

If not, then can we assume the IGate is actually remote from your QTH, but -1 is local?

So, with that final line, it would seem that if you're IGate is using a WIDE1-1,WIDE2-1 path, then -4 will copy it and repeat it locally so that -11 can copy the response at the 911 center.  Without the WIDE1-1, -4 won't digipeat and -11 won't copy it.

The big issue you have is that the -11 HT can't copy the IGate directly when at the 911 center, and apparently there's no bigger digipeater that will digipeat the IGate and be copied by the -11 HT.  No amount of pathing is going to solve an issue of a marginal receiver (the HT) at some distance from the IGate without strong coverage.

But a WIDE1-1,WIDE2-1 path on the IGate should trigger the -4 digipeater to deliver a stronger packet to the HT.

Anyone have any better suggestion?

Lynn (D) - KJ4ERJ - Author of APRSISCE for Windows Mobile and Win32

PS.  An external antenna that you can connect to the HT inside the 911 center would likely also solve your issue.  Apparently the -4 has bigger ears than the HT or it wouldn't copy the IGate while sitting in the parking lot.

--
James
VE6SRV

--
James
VE6SRV


Re: Igates and their use of digi paths

James Ewen
 

While true the nearest permanent digi near me is 30 miles away and a mobile can't hit it unless it's about 15 miles away. I can't even reliably get into any of the digis in the area with the home station. 

So what you are describing is an area with no digipeater coverage. This is not a location for a fill-in digipeater, this area needs a full digipeater. 

A station operating in this area will not be able to participate in APRS operations on the digipeater network as there is no digipeater network in the area. A fill-in digipeater acts as a one way booster in the digipeater network. It will only ever act upon the first path element of a packet. If you put a fill-in digipeater into an area that is not covered by a main digipeater, then there is no way for any traffic (position reports, or more importantly messages) to get back into the area. 

Stations should never use WIDE1-1 anywhere other than as the first element in their outgoing path. Anyone wanting to get information back to station that only has a fill-in digipeater within range from an area 2 digits away would be forced to use WIDE1–1 As a second path element, which we all know is a very bad thing to do. 

Build the network properly and APRS works great. Build it incorrectly and you can have something that is a waste of time, effort, money, and just generally makes people resort to trying stupid things that cause more problems for everyone. 

James 
VE6SRV


On Sat, Jun 20, 2020 at 10:12 PM Greg Depew <goatherder_4891@...> wrote:
See below



Greg KB3KBR Sent from my Verizon, Samsung Galaxy smartphone


-------- Original message --------
From: James Ewen <ve6srv@...>
Date: 6/20/20 20:06 (GMT-05:00)
Subject: Re: [APRSISCE] Igates and their use of digi paths

A WIDE1-1 digipeater should be a located in an area where the main digipeaters can be heard and copied, but low powered handheld stations can’t get the attention of the main digipeater. A WIDE1-1 digipeater fills in and helps the low powered handheld stations get that first hop into the digipeater network. 

Agree wholeheartedly.

High powered (5 watts or more) mobile stations and fixed stations should never use an outgoing path of WIDE1-1. Digipeaters should be located at sites that provide advantageous coverage of the local area. A digipeater should NEVER EVER use WIDE1-1 as an outgoing path. If a digipeater is located such that it requires help from a home fill-in digipeater to be heard by the main digipeaters, it should shut down and removed from service. It is causing more congestion of the local network than it is helping. 

While true the nearest permanent digi near me is 30 miles away and a mobile can't hit it unless it's about 15 miles away. I can't even reliably get into any of the digis in the area with the home station. The network around here is almost non existent. My goal (which was solved with Lynn's advice of setting the gate to Wide1-1 to make the fill in pass the traffic back) was to use the fill in mobile in areas where I know the handheld can't get out. I used it in such a way tonight on our local lake using the handheld on the kayak to go back to mobile fill in and get back to the main digigate at my house. Successfully was able to send and receive messages to Wxbot and SMSGATE. 

If there are any other fill ins that my main digigate lights up I don't know where they are. Other than myself, theres only 2 other people running APRS in my county. One is using a deaf tracker and the other is in the process of getting a solar digi setup on his towns water tower which should increase the coverage to most of the southern part of the county. 

Unfortunately my local club has zero interest in APRS and when I approached our repeater guru about getting stuff on our main tower he shot me down with concerns of it desensing the repeater.  I would love to get high sites but not enough intrest has taken hold even after I held a presentation on it a couple years back. 




On Sat, Jun 20, 2020 at 10:44 AM Greg Depew <goatherder_4891@...> wrote:
Would it be better for me to change 4 to respond to Wide2-2 or have the 1 the igate put out Wide1-1 and maybe light up digis that are very far away? 

Sometimes I can get into a big digi in Ohio but I can't hear it back on anything but the -1, and I've seen my packets be delayed while they hop through the system on open days then get regated about a min later sometimes in Canada or a different place in Ohio. 



Greg KB3KBR Sent from my Verizon, Samsung Galaxy smartphone



-------- Original message --------
From: Lynn Deffenbaugh <kj4erj@...>
Date: 6/19/20 19:48 (GMT-05:00)
Subject: Re: [APRSISCE] Igates and their use of digi paths

On 6/19/2020 6:38 PM, Greg Depew wrote:
Can you give a more complete description of what all is involved?

KB3KBR-11 is what station?  Software, TNC and radio please.

11 is a Yaesu Ft1d

Same for -4 (a WIDE1-1 digi) 

4 is a fill in digi , TinyTrak 4 with GPS and and FT 8800 in a go box programmed to only respond to Wide1-1 and it's own callsign 

Same for -1 (presumably a WIDE2 digi)

1 is APRSIS32 via sound card Signal link into an Ftm 350and is an igate and digi that responds to Wide1-1 and Wide2-2 

Same for the IGate and please include callsign-SSID with the other 3 pieces of the puzzle.

And some idea of who can copy who directly.  Can -1 copy the IGate directly or does the IGate need the boost from -4 to get to -1?  

1 is the igate, 4 is my mobile fill in that I'm using to get 11 back to the igate 

You've already mentioned that you can't hear -1 indoors, but only -4.  Can you copy the IGate indoors?  

When I'm at work inside our 911 center our grounding halo blocks just about everything. 4 is sitting in the truck in the parking lot and can hear 1 and 11. 11 can only hear 1 if it's out side and its iffy if 1 can hear 11 without either holding the antenna in the or more power.

If not, then can we assume the IGate is actually remote from your QTH, but -1 is local?

So, with that final line, it would seem that if you're IGate is using a WIDE1-1,WIDE2-1 path, then -4 will copy it and repeat it locally so that -11 can copy the response at the 911 center.  Without the WIDE1-1, -4 won't digipeat and -11 won't copy it.

The big issue you have is that the -11 HT can't copy the IGate directly when at the 911 center, and apparently there's no bigger digipeater that will digipeat the IGate and be copied by the -11 HT.  No amount of pathing is going to solve an issue of a marginal receiver (the HT) at some distance from the IGate without strong coverage.

But a WIDE1-1,WIDE2-1 path on the IGate should trigger the -4 digipeater to deliver a stronger packet to the HT.

Anyone have any better suggestion?

Lynn (D) - KJ4ERJ - Author of APRSISCE for Windows Mobile and Win32

PS.  An external antenna that you can connect to the HT inside the 911 center would likely also solve your issue.  Apparently the -4 has bigger ears than the HT or it wouldn't copy the IGate while sitting in the parking lot.

--
James
VE6SRV

--
James
VE6SRV


Re: Igates and their use of digi paths

Greg Depew
 

See below



Greg KB3KBR Sent from my Verizon, Samsung Galaxy smartphone


-------- Original message --------
From: James Ewen <ve6srv@...>
Date: 6/20/20 20:06 (GMT-05:00)
To: APRSISCE@groups.io
Subject: Re: [APRSISCE] Igates and their use of digi paths

A WIDE1-1 digipeater should be a located in an area where the main digipeaters can be heard and copied, but low powered handheld stations can’t get the attention of the main digipeater. A WIDE1-1 digipeater fills in and helps the low powered handheld stations get that first hop into the digipeater network. 

Agree wholeheartedly.

High powered (5 watts or more) mobile stations and fixed stations should never use an outgoing path of WIDE1-1. Digipeaters should be located at sites that provide advantageous coverage of the local area. A digipeater should NEVER EVER use WIDE1-1 as an outgoing path. If a digipeater is located such that it requires help from a home fill-in digipeater to be heard by the main digipeaters, it should shut down and removed from service. It is causing more congestion of the local network than it is helping. 

While true the nearest permanent digi near me is 30 miles away and a mobile can't hit it unless it's about 15 miles away. I can't even reliably get into any of the digis in the area with the home station. The network around here is almost non existent. My goal (which was solved with Lynn's advice of setting the gate to Wide1-1 to make the fill in pass the traffic back) was to use the fill in mobile in areas where I know the handheld can't get out. I used it in such a way tonight on our local lake using the handheld on the kayak to go back to mobile fill in and get back to the main digigate at my house. Successfully was able to send and receive messages to Wxbot and SMSGATE. 

If there are any other fill ins that my main digigate lights up I don't know where they are. Other than myself, theres only 2 other people running APRS in my county. One is using a deaf tracker and the other is in the process of getting a solar digi setup on his towns water tower which should increase the coverage to most of the southern part of the county. 

Unfortunately my local club has zero interest in APRS and when I approached our repeater guru about getting stuff on our main tower he shot me down with concerns of it desensing the repeater.  I would love to get high sites but not enough intrest has taken hold even after I held a presentation on it a couple years back. 




On Sat, Jun 20, 2020 at 10:44 AM Greg Depew <goatherder_4891@...> wrote:
Would it be better for me to change 4 to respond to Wide2-2 or have the 1 the igate put out Wide1-1 and maybe light up digis that are very far away? 

Sometimes I can get into a big digi in Ohio but I can't hear it back on anything but the -1, and I've seen my packets be delayed while they hop through the system on open days then get regated about a min later sometimes in Canada or a different place in Ohio. 



Greg KB3KBR Sent from my Verizon, Samsung Galaxy smartphone



-------- Original message --------
From: Lynn Deffenbaugh <kj4erj@...>
Date: 6/19/20 19:48 (GMT-05:00)
Subject: Re: [APRSISCE] Igates and their use of digi paths

On 6/19/2020 6:38 PM, Greg Depew wrote:
Can you give a more complete description of what all is involved?

KB3KBR-11 is what station?  Software, TNC and radio please.

11 is a Yaesu Ft1d

Same for -4 (a WIDE1-1 digi) 

4 is a fill in digi , TinyTrak 4 with GPS and and FT 8800 in a go box programmed to only respond to Wide1-1 and it's own callsign 

Same for -1 (presumably a WIDE2 digi)

1 is APRSIS32 via sound card Signal link into an Ftm 350and is an igate and digi that responds to Wide1-1 and Wide2-2 

Same for the IGate and please include callsign-SSID with the other 3 pieces of the puzzle.

And some idea of who can copy who directly.  Can -1 copy the IGate directly or does the IGate need the boost from -4 to get to -1?  

1 is the igate, 4 is my mobile fill in that I'm using to get 11 back to the igate 

You've already mentioned that you can't hear -1 indoors, but only -4.  Can you copy the IGate indoors?  

When I'm at work inside our 911 center our grounding halo blocks just about everything. 4 is sitting in the truck in the parking lot and can hear 1 and 11. 11 can only hear 1 if it's out side and its iffy if 1 can hear 11 without either holding the antenna in the or more power.

If not, then can we assume the IGate is actually remote from your QTH, but -1 is local?

So, with that final line, it would seem that if you're IGate is using a WIDE1-1,WIDE2-1 path, then -4 will copy it and repeat it locally so that -11 can copy the response at the 911 center.  Without the WIDE1-1, -4 won't digipeat and -11 won't copy it.

The big issue you have is that the -11 HT can't copy the IGate directly when at the 911 center, and apparently there's no bigger digipeater that will digipeat the IGate and be copied by the -11 HT.  No amount of pathing is going to solve an issue of a marginal receiver (the HT) at some distance from the IGate without strong coverage.

But a WIDE1-1,WIDE2-1 path on the IGate should trigger the -4 digipeater to deliver a stronger packet to the HT.

Anyone have any better suggestion?

Lynn (D) - KJ4ERJ - Author of APRSISCE for Windows Mobile and Win32

PS.  An external antenna that you can connect to the HT inside the 911 center would likely also solve your issue.  Apparently the -4 has bigger ears than the HT or it wouldn't copy the IGate while sitting in the parking lot.

--
James
VE6SRV


Re: Igates and their use of digi paths

James Ewen
 

A WIDE1-1 digipeater should be a located in an area where the main digipeaters can be heard and copied, but low powered handheld stations can’t get the attention of the main digipeater. A WIDE1-1 digipeater fills in and helps the low powered handheld stations get that first hop into the digipeater network. 

High powered (5 watts or more) mobile stations and fixed stations should never use an outgoing path of WIDE1-1. Digipeaters should be located at sites that provide advantageous coverage of the local area. A digipeater should NEVER EVER use WIDE1-1 as an outgoing path. If a digipeater is located such that it requires help from a home fill-in digipeater to be heard by the main digipeaters, it should shut down and removed from service. It is causing more congestion of the local network than it is helping. 



On Sat, Jun 20, 2020 at 10:44 AM Greg Depew <goatherder_4891@...> wrote:
Would it be better for me to change 4 to respond to Wide2-2 or have the 1 the igate put out Wide1-1 and maybe light up digis that are very far away? 

Sometimes I can get into a big digi in Ohio but I can't hear it back on anything but the -1, and I've seen my packets be delayed while they hop through the system on open days then get regated about a min later sometimes in Canada or a different place in Ohio. 



Greg KB3KBR Sent from my Verizon, Samsung Galaxy smartphone



-------- Original message --------
From: Lynn Deffenbaugh <kj4erj@...>
Date: 6/19/20 19:48 (GMT-05:00)
Subject: Re: [APRSISCE] Igates and their use of digi paths

On 6/19/2020 6:38 PM, Greg Depew wrote:
Can you give a more complete description of what all is involved?

KB3KBR-11 is what station?  Software, TNC and radio please.

11 is a Yaesu Ft1d

Same for -4 (a WIDE1-1 digi) 

4 is a fill in digi , TinyTrak 4 with GPS and and FT 8800 in a go box programmed to only respond to Wide1-1 and it's own callsign 

Same for -1 (presumably a WIDE2 digi)

1 is APRSIS32 via sound card Signal link into an Ftm 350and is an igate and digi that responds to Wide1-1 and Wide2-2 

Same for the IGate and please include callsign-SSID with the other 3 pieces of the puzzle.

And some idea of who can copy who directly.  Can -1 copy the IGate directly or does the IGate need the boost from -4 to get to -1?  

1 is the igate, 4 is my mobile fill in that I'm using to get 11 back to the igate 

You've already mentioned that you can't hear -1 indoors, but only -4.  Can you copy the IGate indoors?  

When I'm at work inside our 911 center our grounding halo blocks just about everything. 4 is sitting in the truck in the parking lot and can hear 1 and 11. 11 can only hear 1 if it's out side and its iffy if 1 can hear 11 without either holding the antenna in the or more power.

If not, then can we assume the IGate is actually remote from your QTH, but -1 is local?

So, with that final line, it would seem that if you're IGate is using a WIDE1-1,WIDE2-1 path, then -4 will copy it and repeat it locally so that -11 can copy the response at the 911 center.  Without the WIDE1-1, -4 won't digipeat and -11 won't copy it.

The big issue you have is that the -11 HT can't copy the IGate directly when at the 911 center, and apparently there's no bigger digipeater that will digipeat the IGate and be copied by the -11 HT.  No amount of pathing is going to solve an issue of a marginal receiver (the HT) at some distance from the IGate without strong coverage.

But a WIDE1-1,WIDE2-1 path on the IGate should trigger the -4 digipeater to deliver a stronger packet to the HT.

Anyone have any better suggestion?

Lynn (D) - KJ4ERJ - Author of APRSISCE for Windows Mobile and Win32

PS.  An external antenna that you can connect to the HT inside the 911 center would likely also solve your issue.  Apparently the -4 has bigger ears than the HT or it wouldn't copy the IGate while sitting in the parking lot.

--
James
VE6SRV


Re: Question About Yellow Path Lines & MSGs That I receive

Mike Jordan <mjordan@...>
 

Thanks a lot for the information, Robert. I had gone through all of the sections of the Wiki when I was setting up and a few times afterwards and I did see the part about the message notifier and having a notice if a message was waiting. I didn't find anything on the types of messages that would be received though or much about the Mic-E ones, so thinks for that info. I've now turned off the notifications since I don't do anything with them and don't see a need to communicate anything back.

I did configure Paths-Appearances during my setup, although I wasn't sure about some of the settings. I do have it set to show RF only and not internet as there are a lot of red lines when I have the Network Links box checked.

Thanks again for the info. So much to learn with this, that's for sure. I'll keep going back to the Wiki to see if I can dig out some of the answers to some of my other questions.

Mike

On 6/20/2020 8:08 AM, Rob Giuliano via groups.io wrote:
A good place to start on the features of APRSIS32 is the WIKI:
Welcome to APRSISCE/32 - APRSISCE/32 The future of Amateur Radio APRS
<http://aprsisce.wikidot.com/start>




Welcome to APRSISCE/32 - APRSISCE/32 The future of Amateur Radio APRS

APRSISCE/32 The future of Amateur Radio APRS, The most fully featured
Windows APRS software available, Official ...

<http://aprsisce.wikidot.com/start>

I did a search (top right corner box with "search this site") on the
WIKI with something as simple as "Circle" and will admit what came up
didn't show anything obvious. However, my next try was to search on
"Map circle" (because the circle was showing on the map). First Item
showed Map Prefetch and with verbage of " ... The yellow *circle* will
begin expanding ...". Click on it and you get more detail. I could
have used "Expanding circle".


Q1: yellow lines that shoot out from my position
These are typically RF path lines. They cross as different station
DIGI. You can be configured what is displayed in >Menu >Screen >Paths.
For more information, I again point to the WIKI.

Q2: MSG Boc What do, if anything, with these?
You don't need to do anything, unless you want to communicate with the
station sending. BUT to communicate, you have to type something and hit
<Send>. Just hitting <Send> won't do anything because there is nothing
to send.

Most of those message are coming in from stations sending with the Mic-E
format. The Mic-E protocol has "Status" as part of the message. The
APRS spec for APRS clients says that when a mess with certain status
(like Special or Emergency") is received, the client should have action
taken. I won't go into detail on status vs. action. In >Menu
>Configure >Mic-E Notifications you can configure what APRS-IS does
with these.

Robert Giuliano
KB8RCO


Re: Igates and their use of digi paths

Greg Depew
 

Would it be better for me to change 4 to respond to Wide2-2 or have the 1 the igate put out Wide1-1 and maybe light up digis that are very far away? 

Sometimes I can get into a big digi in Ohio but I can't hear it back on anything but the -1, and I've seen my packets be delayed while they hop through the system on open days then get regated about a min later sometimes in Canada or a different place in Ohio. 



Greg KB3KBR Sent from my Verizon, Samsung Galaxy smartphone



-------- Original message --------
From: Lynn Deffenbaugh <kj4erj@...>
Date: 6/19/20 19:48 (GMT-05:00)
To: APRSISCE@groups.io
Subject: Re: [APRSISCE] Igates and their use of digi paths

On 6/19/2020 6:38 PM, Greg Depew wrote:
Can you give a more complete description of what all is involved?

KB3KBR-11 is what station?  Software, TNC and radio please.

11 is a Yaesu Ft1d

Same for -4 (a WIDE1-1 digi) 

4 is a fill in digi , TinyTrak 4 with GPS and and FT 8800 in a go box programmed to only respond to Wide1-1 and it's own callsign 

Same for -1 (presumably a WIDE2 digi)

1 is APRSIS32 via sound card Signal link into an Ftm 350and is an igate and digi that responds to Wide1-1 and Wide2-2 

Same for the IGate and please include callsign-SSID with the other 3 pieces of the puzzle.

And some idea of who can copy who directly.  Can -1 copy the IGate directly or does the IGate need the boost from -4 to get to -1?  

1 is the igate, 4 is my mobile fill in that I'm using to get 11 back to the igate 

You've already mentioned that you can't hear -1 indoors, but only -4.  Can you copy the IGate indoors?  

When I'm at work inside our 911 center our grounding halo blocks just about everything. 4 is sitting in the truck in the parking lot and can hear 1 and 11. 11 can only hear 1 if it's out side and its iffy if 1 can hear 11 without either holding the antenna in the or more power.

If not, then can we assume the IGate is actually remote from your QTH, but -1 is local?

So, with that final line, it would seem that if you're IGate is using a WIDE1-1,WIDE2-1 path, then -4 will copy it and repeat it locally so that -11 can copy the response at the 911 center.  Without the WIDE1-1, -4 won't digipeat and -11 won't copy it.

The big issue you have is that the -11 HT can't copy the IGate directly when at the 911 center, and apparently there's no bigger digipeater that will digipeat the IGate and be copied by the -11 HT.  No amount of pathing is going to solve an issue of a marginal receiver (the HT) at some distance from the IGate without strong coverage.

But a WIDE1-1,WIDE2-1 path on the IGate should trigger the -4 digipeater to deliver a stronger packet to the HT.

Anyone have any better suggestion?

Lynn (D) - KJ4ERJ - Author of APRSISCE for Windows Mobile and Win32

PS.  An external antenna that you can connect to the HT inside the 911 center would likely also solve your issue.  Apparently the -4 has bigger ears than the HT or it wouldn't copy the IGate while sitting in the parking lot.


Re: Question About Yellow Path Lines & MSGs That I receive

Rob Giuliano
 


I did a search (top right corner box with "search this site") on the WIKI with something as simple as "Circle" and will admit what came up didn't show anything obvious.  However, my next try was to search on "Map circle" (because the circle was showing on the map).  First Item showed Map Prefetch and with verbage of " ... The yellow circle will begin expanding ...".  Click on it and you get more detail.  I could have used "Expanding circle".


Q1: yellow lines that shoot out from my position
These are typically RF path lines.  They cross as different station DIGI.  You can be configured what is displayed in >Menu >Screen >Paths.
For more information, I again point to the WIKI. 

Q2: MSG Boc What do, if anything, with these?
You don't need to do anything, unless you want to communicate with the station sending.  BUT to communicate, you have to type something and hit <Send>.  Just hitting <Send> won't do anything because there is nothing to send.

Most of those message are coming in from stations sending with the Mic-E format.  The Mic-E protocol has "Status" as part of the message.  The APRS spec for APRS clients says that when a mess with certain status (like Special or Emergency") is received, the client should have action taken.  I won't go into detail on status vs. action.  In >Menu >Configure >Mic-E Notifications you can configure what APRS-IS does with these.

Robert Giuliano
KB8RCO



On Saturday, June 20, 2020, 12:58:43 AM EDT, Mike Jordan <mjordan@...> wrote:


I've only been running APRSIS for a couple of weeks and really only been
doing packet starting just before that.  Some of the things are pretty
clear, some I've been able to figure out and a few I've made guesses
at... which leaves a bunch of stuff I'm still trying to figure out.
There is a lot of information about setting up APRS with various modems,
sound cards, TNC's, etc., but not a lot about actual day to day running
of the thing in any one place.

APRSIS was pretty easy to get set up and running along with Direwolf and
SoundModem, which I switch back and forth on because I think SoundModem
is cleaner but Direwolf seems to decode faster and provide more
information.  I had it up and receiving APRS information in just a
couple of days on my Icom IC-746Pro. I then switched it over to an older
Icom IC-V8000 I had sitting on the shelf so I could free up the
IC-746Pro. It's been running just fine for the last week on the IC-V8000.

Now that I've had a chance to watch it run for awhile and dig for
answers to some of my questions I have a few things I'm curious about.
I'm set up as a TX/RX IGate with one hop (wide2-1).

First question is about the yellow lines that shoot out from my position
icon and zig zag back and forth (something crossing back over itself)
all over the place.  I assume these are internet paths but I've read
(without any detail) that they are RF paths, yet I don't see anything
come into me over the radio.  What are these showing and why do they go
through so many other nodes? Sometimes they go way out and then angle
back to a closer node before ending. I haven't found anything in the
logs that I've looked in to tell me anything.

Second question is the messages that I'm receiving. Every hour to a
couple of times a day, I will get a message indicator in the MSG box.
They appear to be from a mobile radio in beacon mode.  One example is:

KE7VGF-15 <-> KJ4TX-10
06:14:23 New Chat Between KE7VGF-15 and KJ4TX-10 on 2020-06-17
20:07:41> Mic-E:KE7VGF-15 Transmitted Status(Special)
New Date 2020-06-19
12:38:41> Mic-E:KE7VGF-15 Transmitted Status(Special)

In the message box it has Ack and Best checked. I can change it from RF
to internet. There is the send button and a place to enter a message.

What do, if anything, with these? I have tried clicking Send with
nothing happening and Xing out of them. I assume I can enter a message
and send it back but I haven't done that.  Should I be doing anything
with these messages or just ignore them and close them after opening
them up?  I get them from about 7 or so stations through out the day.

It's been interesting, especially seeing all the different kinds of
symbols that show up. I'm not sure if I'm providing any benefit to my
area though. We have several big digipeaters and a number of IGates in
my area. Most are WinAPRS and D-Star nodes though. But the coverage
around the Portland, OR area is pretty good, and though I have both RF
and internet traffic of some kind going through me, I'm not sure if my
node is actually doing anything useful. It is giving me something to do
with my radios and all of the computers I have laying around though and
kept me off the streets. LOL!

Thanks for any help on these questions.

Mike
KJ4TX

--
Hillsboro, Oregon
Bouvier des Flandres - Herding & Working Dogs
http://www.sitnprettyphoto.com - Photos of Agility, Herding & more



801 - 820 of 35339