Date   

'TCPIP' seen in from an ISS packet decode

KD7YZ Bob
 

... and then apparently DigiPeated by me.

here are a couple:

-----------------------------------------------------------------------------
3:Fm KD7YZ-15 To APWW10 Via WIDE2-1 <UI pid=F0 Len=88 >[19:38:26]
}K4KDR-6>CQ,RS0ISS,TCPIP,KD7YZ-15*::VE3FFB :Heard you via ISS in Montpelier, VA FM17es

-------------------------------------------------------------------------------
3:Fm KD7YZ-15 To APWW10 Via WIDE2-1 <UI pid=F0 Len=79 >[21:14:51]
}KC9YTT>CQ,TCPIP,KD7YZ-15*::KA8YES-6 :Your 599 in Williamsfield, Illinois! 73's
---------------------------------------------------------------------------------------------------------------


Have seen this a lot and wonder if I have APRSIS/32 config wrong ... the Port-3 is an RTL/SDR-Console off a separate antenna. A monitoring setup for me to verify things sometimes. It comes thru the AGWPE-Telnet link/Port in APRSIS32.


--
--
KD7YZ Bob EM88LL


Re: APRSIS23 HF APRS & PTC-IIex

John Brent - VA7WPN
 

I have done the capacitor mod, with no change. 

SCS has given me instructions to do a memory dump / check in the sys mode to try and clear the flash memory.

more to follow.


Re: *int*

Rob Giuliano
 


Neither listed what htese were.Might be something to add in the first one as clarification.

These are packets generated internally by APRSIS32.
You can disable these from showing in the through the >Configure >Scroller option in the menu (as described in the second link).

Robert Giuliano
KB8RCO



On Sunday, January 26, 2020, 11:35:46 AM EST, g6yrk@... <g6yrk@...> wrote:


Hi all
I have another question, When I am watching the " scroller" screen sometimes see  *int* at the side of my out going transmision.
Any explonations please?

Steve G6YRK


*int*

g6yrk@...
 

Hi all
I have another question, When I am watching the " scroller" screen sometimes see  *int* at the side of my out going transmision.
Any explonations please?

Steve G6YRK


Re: Getting APRSIS TO tx/rx on RF

Kako Lizares
 

Hi try to check your soundcard config.. 


Re: Getting APRSIS TO tx/rx on RF

Jeffrey Golas
 

Ah cool I didnt realize that was a thing. Thanks!

Jeff

On Jan 25, 2020, at 11:40 AM, Lynn Deffenbaugh <kj4erj@...> wrote:

Yes, just send an APRS message to the station you want to query.  You can even send an APRS message to yourself to query your own station.

All queries start with a ?.  If you send an invalid query (like ?JUNK) APRSIS32 will respond with the queries that are supported.

        > Support[1/2]: ?APRSD ?APRSL ?APRSH ?APRSM ?APRSO ?APRSP ?APRSS
        > Support[2/2]:?APRST/?PING? ?ABOUT/?APRSV/?VER ?CPU ?DX ?IGATE

The only odd-ball is ?APRSH (query heard).  By default it will respond with the path over which the query was received.   But if you add a trailing * (?APRSH *), it will respond with a list of all stations heard via RF ports.  ?APRSD responds with the direct stations (no hops used), ?APRSL with local (<2 hops and past N minutes).  The number in () will be the calculated used hop count with (0) suppressed for directly-received stations.

https://robust-packet.net/documents/APRS-Queries.pdf has an interesting list although I didn't study it in detail just now.

Lynn (D) - KJ4ERJ - Author of APRSISCE for Windows Mobile and Win32

On 1/25/2020 11:14 AM, Jeffrey Golas wrote:
How do you do these queries? Is it possible to do within the software?

Jeff

On Jan 25, 2020, at 10:37 AM, Lynn Deffenbaugh <kj4erj@...> wrote:

I'm glad we got it worked out.  I'm still surprised that the <Open/CloseCmd>s from the Kenwood APRS radios (lurking beneath the "KISS" port type) actually made your TNC function, but function it did!

According to the query I just did (?APRSH *), you've copied packets from 5 stations in the past 2 hours or so:

G3CWI-5(1) G6YRK-7 M0WIT-9(2) M1VIP-9(2) MB7UMC

G6YRK-7 and MB7UMC were copied direct and the other 3 were via digipeats.  Is G6YRK-7 your APRS HT?  If so, what was the magic to get it decoded and received?

Lynn (D) - KJ4ERJ - Author of APRSISCE for Windows Mobile and Win32

On 1/25/2020 10:02 AM, g6yrk@... wrote:
Well what can I say, what a good job Lynn did last night sorting my problem out, plus I also learnt a lot about APRSIS that I did not know, and I have been using since it since about 2003
but we (Lynn) found the problem was down to the "Kiss" settings, I had it set to Simply (KISS) and my old system running on Win7 was Just "KISS" so changed it and hey presto it worked
and we were chatting on APRSIS untill about 02:30 in the morning trying to sort it 

But Very Many thanks Lynn and putting up with some of my questions

Steve G6YRK  uk


Re: Getting APRSIS TO tx/rx on RF

Lynn Deffenbaugh
 

Yes, just send an APRS message to the station you want to query.  You can even send an APRS message to yourself to query your own station.

All queries start with a ?.  If you send an invalid query (like ?JUNK) APRSIS32 will respond with the queries that are supported.

        > Support[1/2]: ?APRSD ?APRSL ?APRSH ?APRSM ?APRSO ?APRSP ?APRSS
        > Support[2/2]:?APRST/?PING? ?ABOUT/?APRSV/?VER ?CPU ?DX ?IGATE

The only odd-ball is ?APRSH (query heard).  By default it will respond with the path over which the query was received.   But if you add a trailing * (?APRSH *), it will respond with a list of all stations heard via RF ports.  ?APRSD responds with the direct stations (no hops used), ?APRSL with local (<2 hops and past N minutes).  The number in () will be the calculated used hop count with (0) suppressed for directly-received stations.

https://robust-packet.net/documents/APRS-Queries.pdf has an interesting list although I didn't study it in detail just now.

Lynn (D) - KJ4ERJ - Author of APRSISCE for Windows Mobile and Win32

On 1/25/2020 11:14 AM, Jeffrey Golas wrote:
How do you do these queries? Is it possible to do within the software?

Jeff

On Jan 25, 2020, at 10:37 AM, Lynn Deffenbaugh <kj4erj@...> wrote:

I'm glad we got it worked out.  I'm still surprised that the <Open/CloseCmd>s from the Kenwood APRS radios (lurking beneath the "KISS" port type) actually made your TNC function, but function it did!

According to the query I just did (?APRSH *), you've copied packets from 5 stations in the past 2 hours or so:

G3CWI-5(1) G6YRK-7 M0WIT-9(2) M1VIP-9(2) MB7UMC

G6YRK-7 and MB7UMC were copied direct and the other 3 were via digipeats.  Is G6YRK-7 your APRS HT?  If so, what was the magic to get it decoded and received?

Lynn (D) - KJ4ERJ - Author of APRSISCE for Windows Mobile and Win32

On 1/25/2020 10:02 AM, g6yrk@... wrote:
Well what can I say, what a good job Lynn did last night sorting my problem out, plus I also learnt a lot about APRSIS that I did not know, and I have been using since it since about 2003
but we (Lynn) found the problem was down to the "Kiss" settings, I had it set to Simply (KISS) and my old system running on Win7 was Just "KISS" so changed it and hey presto it worked
and we were chatting on APRSIS untill about 02:30 in the morning trying to sort it 

But Very Many thanks Lynn and putting up with some of my questions

Steve G6YRK  uk


Re: Getting APRSIS TO tx/rx on RF

Jeffrey Golas
 

How do you do these queries? Is it possible to do within the software?

Jeff

On Jan 25, 2020, at 10:37 AM, Lynn Deffenbaugh <kj4erj@...> wrote:

I'm glad we got it worked out.  I'm still surprised that the <Open/CloseCmd>s from the Kenwood APRS radios (lurking beneath the "KISS" port type) actually made your TNC function, but function it did!

According to the query I just did (?APRSH *), you've copied packets from 5 stations in the past 2 hours or so:

G3CWI-5(1) G6YRK-7 M0WIT-9(2) M1VIP-9(2) MB7UMC

G6YRK-7 and MB7UMC were copied direct and the other 3 were via digipeats.  Is G6YRK-7 your APRS HT?  If so, what was the magic to get it decoded and received?

Lynn (D) - KJ4ERJ - Author of APRSISCE for Windows Mobile and Win32

On 1/25/2020 10:02 AM, g6yrk@... wrote:
Well what can I say, what a good job Lynn did last night sorting my problem out, plus I also learnt a lot about APRSIS that I did not know, and I have been using since it since about 2003
but we (Lynn) found the problem was down to the "Kiss" settings, I had it set to Simply (KISS) and my old system running on Win7 was Just "KISS" so changed it and hey presto it worked
and we were chatting on APRSIS untill about 02:30 in the morning trying to sort it 

But Very Many thanks Lynn and putting up with some of my questions

Steve G6YRK  uk


Re: Getting APRSIS TO tx/rx on RF

Lynn Deffenbaugh
 

I'm glad we got it worked out.  I'm still surprised that the <Open/CloseCmd>s from the Kenwood APRS radios (lurking beneath the "KISS" port type) actually made your TNC function, but function it did!

According to the query I just did (?APRSH *), you've copied packets from 5 stations in the past 2 hours or so:

G3CWI-5(1) G6YRK-7 M0WIT-9(2) M1VIP-9(2) MB7UMC

G6YRK-7 and MB7UMC were copied direct and the other 3 were via digipeats.  Is G6YRK-7 your APRS HT?  If so, what was the magic to get it decoded and received?

Lynn (D) - KJ4ERJ - Author of APRSISCE for Windows Mobile and Win32

On 1/25/2020 10:02 AM, g6yrk@... wrote:
Well what can I say, what a good job Lynn did last night sorting my problem out, plus I also learnt a lot about APRSIS that I did not know, and I have been using since it since about 2003
but we (Lynn) found the problem was down to the "Kiss" settings, I had it set to Simply (KISS) and my old system running on Win7 was Just "KISS" so changed it and hey presto it worked
and we were chatting on APRSIS untill about 02:30 in the morning trying to sort it 

But Very Many thanks Lynn and putting up with some of my questions

Steve G6YRK  uk


Re: Getting APRSIS TO tx/rx on RF

g6yrk@...
 

Well what can I say, what a good job Lynn did last night sorting my problem out, plus I also learnt a lot about APRSIS that I did not know, and I have been using since it since about 2003
but we (Lynn) found the problem was down to the "Kiss" settings, I had it set to Simply (KISS) and my old system running on Win7 was Just "KISS" so changed it and hey presto it worked
and we were chatting on APRSIS untill about 02:30 in the morning trying to sort it 

But Very Many thanks Lynn and putting up with some of my questions

Steve G6YRK  uk


Re: Where is "S8RY4Q" generated?

KD7YZ Bob
 

"""So, just to be clear, the D710 is sending beacons position and other type packets using Dire Wolf the same call-SSID (KD7YZ-15) ?"""

That's a digipeat from/or through, me, from a friend of mine who is quite blocked from easy RF transmission in my direction ... to his North. He uses DW, I use APRSIS32-Develop

that tocall.txt seems familiar. I'll try to find it here or on the I-Net

thanks again

--
--
KD7YZ Bob EM88LL


Re: Where is "S8RY4Q" generated?

Randy Love
 

So, just to be clear, the D710 is sending beacons position and other type packets using Dire Wolf the same call-SSID (KD7YZ-15) ?

What you're seeing is two different uses of the TO call field. 

The S8RY4Q is from a Mic-E encoded packet which used the TO call to send part of the position information. In that case, the TO call doesn't ID the type of equipment/ software used.  

The APWW10 in the TO call field is an equipment/software identifier. If you look closely at the packets that have that in the TO field, you will notice that they are not position packets,  so they don't need to use the TO call field for that information.

Sorry, I'm on my phone so I can't get to the links directly, but if you go to aprs.org and search the page for APRS spec, you will find in .pdf file that it downloads a definition of Mic-E encoding scheme. On that same page is a link to the APRS 1.1 addendum page which has a link on it to the tocall.txt with the TO call definitions.

The thing to understand here is that the TO call field isn't always used to identify equipment/ software being used, but also can be used as part of the location information when position data is sent in Mic-E format, even in the same equipment/software.

Randy 
WF5X 


On Sat, Jan 25, 2020, 6:57 AM KD7YZ Bob <kd7yz@...> wrote:
for example, looking on Findu, for KD7YZ-15, 5 mins ago, I see I have 2 "TO"'s


KD7YZ-15>S8RY4Q,WIDE2-2,qAR,KG4DVE-1:'oY"l  -/]Greenup County 900' MSL Stacked Loops 50'=
KD7YZ-15>APWW10,TCPIP*,qAC,T2OSAKA:T#422,100,048,093,128,000,10100000
KD7YZ-15>APWW10,TCPIP*,qAC,T2OSAKA:T#423,100,048,093,128,000,10100000
KD7YZ-15>APWW10,TCPIP*,qAC,T2OSAKA:<IGATE,MSG_CNT=2,LOC_CNT=3,DIR_CNT=3,RF_CNT=4
KD7YZ-15>S8RY4Q,WIDE2-2,qAR,KG4DVE-1:'oY"l  -/]=
--
--
KD7YZ Bob EM88LL




Re: Where is "S8RY4Q" generated?

KD7YZ Bob
 

for example, looking on Findu, for KD7YZ-15, 5 mins ago, I see I have 2 "TO"'s


KD7YZ-15>S8RY4Q,WIDE2-2,qAR,KG4DVE-1:'oY"l -/]Greenup County 900' MSL Stacked Loops 50'=
KD7YZ-15>APWW10,TCPIP*,qAC,T2OSAKA:T#422,100,048,093,128,000,10100000
KD7YZ-15>APWW10,TCPIP*,qAC,T2OSAKA:T#423,100,048,093,128,000,10100000
KD7YZ-15>APWW10,TCPIP*,qAC,T2OSAKA:<IGATE,MSG_CNT=2,LOC_CNT=3,DIR_CNT=3,RF_CNT=4
KD7YZ-15>S8RY4Q,WIDE2-2,qAR,KG4DVE-1:'oY"l -/]=
--
--
KD7YZ Bob EM88LL


Re: Where is "S8RY4Q" generated?

KD7YZ Bob
 

On Fri, Jan 24, 2020 at 08:34 AM, Randy Love wrote:


APRS Mic-E encoding
I tried various searches relating to that, Mic-E, and do not see how to break-out the S8RY4Q ... nor the

2:Fm N4PWH-10 To APDW15 Via KD7YZ-15,WIDE1*,WIDE2-1 <UI pid=F0 Len=57 >[06:27:56]
!3819.85NI08258.30W#RasPi I-Gate/Digipeater in Grayson KY


APDW15, which I believe means he used DireWolf

I haven't a copy of the one I usually saw on my packets ...something akin to APWWD10-ish as I am using a KWD D710 .. but, at that time I had seen other KWD users and theirs, being 700's, had something similar which included the 700.

I am guessing I have changes a setup in the D710GA or in APRS32-Devel version, that altered what I was sending.

I guess it doesn't really matter as I am getting out; am rx'ing and otherwise Digipeat and iGating ...

just that I was curious what the CallSign TO APWDW10 or TO S8RY4Q breaks down to ... no joy on several googles this morning.

--
KD7YZ Bob EM88LL


Re: Getting APRSIS TO tx/rx on RF

Lynn Deffenbaugh
 

He is finally running the development version and has opted to go to a private exchange with me.  I'll try to encourage him to get back to the group so others can a) benefit, and/or b) think of things that I haven't.

Lynn (D) - KJ4ERJ - Author of APRSISCE for Windows Mobile and Win32

On 1/24/2020 7:26 PM, Rob Giuliano via Groups.Io wrote:
Can you copy the exe and xml from the old computer?

Otherwise, there is no link to the development version.  The non-development version will download and install it when the XML setting is set (per Lynn's previous email and link to the wiki.


On Fri, Jan 24, 2020 at 13:53, g6yrk@...
Hi again, I have uninstalled the version I had but cannot find a Development version
have you a link please ?


Re: Getting APRSIS TO tx/rx on RF

Rob Giuliano
 

Can you copy the exe and xml from the old computer?

Otherwise, there is no link to the development version.  The non-development version will download and install it when the XML setting is set (per Lynn's previous email and link to the wiki.


On Fri, Jan 24, 2020 at 13:53, g6yrk@...
<g6yrk@...> wrote:
Hi again, I have uninstalled the version I had but cannot find a Development version
have you a link please ?


Re: Getting APRSIS TO tx/rx on RF

Lynn Deffenbaugh
 

Like I said, follow the instructions at the following link.  You start with the general release version, close it, edit the APRSIS32.xml file as described, restart it, and then check About.  There will be a button there to install the upgrade.

http://aprsisce.wikidot.com/doc:development-version

There is no direct download link for the development version.

Lynn (D) - KJ4ERJ - Author of APRSISCE for Windows Mobile and Win32

On 1/24/2020 1:53 PM, g6yrk@... wrote:
Hi again, I have uninstalled the version I had but cannot find a Development version
have you a link please ?


Re: Getting APRSIS TO tx/rx on RF

g6yrk@...
 

Hi again, I have uninstalled the version I had but cannot find a Development version
have you a link please ?


Re: ME

Lynn Deffenbaugh
 

I am trying to understand your problem.  It sounds like you may be running the .EXE in a protected directory causing it to not be able to record its current configuration.

Or if you're trying to get rid of ME, that's the label that APRSIS32 puts on the current station.  It will be visible at all times.

What popup have you filled 4 times?  That's another indication that the configuration is not being saved properly, likely due to running in a non-writeable directory or executing directly out of the .ZIP file.  You might want to check:

http://aprsisce.wikidot.com/initial-startup

Lynn (D) - KJ4ERJ - Author of APRSISCE for Windows Mobile and Win32

On 1/22/2020 8:06 PM, pat obrien wrote:
How do you get rid of the ME in the setup, I have filled the windows popup 4x, and it still comes up me, I have got the qth down and dragged it to transmit and still ME, Any help appreciated.
POB/K8LEN


Re: Getting APRSIS TO tx/rx on RF

Lynn Deffenbaugh
 

In the About box it should show a Built: date/timestamp.  If it is 2012, you are not on the latest development.  Follow the instructions at:

http://aprsisce.wikidot.com/doc:development-version

Note: In Development mode, it will say "Current Development version verified".

Lynn (D) - KJ4ERJ - Author of APRSISCE for Windows Mobile and Win32

On 1/24/2020 10:27 AM, g6yrk@... wrote:
Hi Lynn I am not sure what version it is as all it says is: "Current version verified" but not sure about the development mode I cannot find that on the software