Date   

Re: APRSISCE/TN-D710 set-up

Lynn Deffenbaugh
 

Just remember, Windows only allows one program at a time to access any given COM port.  But to change the frequency, you'll have to cable to the base unit, not the head, so you'll need two cables and COM ports anyway.

Lynn (D) - KJ4ERJ - Author of APRSISCE for Windows Mobile and Win32

On 9/10/2019 7:13 AM, Bob KD7YZ kd7yz@denstarfarm.us [aprsisce] wrote:
On 9/9/2019 10:51, ka0azs@earthlink.net [aprsisce] wrote:
I've been walking a couple of hams through this recently and finally
found time to write up what I have found to work. When I get a chance
I'll add screen shots and post to the files section. Hope this helps:


First, read this page on the APRSIS32 Wiki:
http://aprsisce.wikidot.com/port:kenwood-tm-d710


Computer Set Up:


Check the baud rate of the COM port you will be using in device manager .......
OK Randy, I have dutifully followed the outline u sent ( this one on
this page is the same if anyone else asks).

Now to see if my PSTRotator progream will setr the Rx on the D710GA to
match the Sat Freq.

Not that you covered that. However the "WiKi" article "seems" to say the
D710 can be taken over ... so we'll see.


--
73
Bob KD7YZ
AMSAT LM #901


------------------------------------
Posted by: Bob KD7YZ <kd7yz@denstarfarm.us>
------------------------------------


------------------------------------

Yahoo Groups Links




Re: APRSISCE/TN-D710 set-up

KD7YZ Bob
 

On 9/9/2019 10:51, ka0azs@earthlink.net [aprsisce] wrote:
I've been walking a couple of hams through this recently and finally found time to write up what I have found to work. When I get a chance I'll add screen shots and post to the files section. Hope this helps:
First, read this page on the APRSIS32 Wiki: http://aprsisce.wikidot.com/port:kenwood-tm-d710
Computer Set Up:
Check the baud rate of the COM port you will be using in device manager .......
OK Randy, I have dutifully followed the outline u sent ( this one on this page is the same if anyone else asks).

Now to see if my PSTRotator progream will setr the Rx on the D710GA to match the Sat Freq.

Not that you covered that. However the "WiKi" article "seems" to say the D710 can be taken over ... so we'll see.


--
73
Bob KD7YZ
AMSAT LM #901


Re: APRSISCE/TN-D710 set-up

Randy Allen
 

The only issue I see with that cable is that it has a straight data connector rather the 90 degree connector of the Kenwood stock cable (which of course these days usually requires a serial-USB converter). That would not work for me in mobile operations as the space between my control head and dash is too tight (the stock cable just barely fits). It would not be an issue working a portable station out of the vehicle.

That being said, I have this bookmarked for future reference. Thanks.

73

Randy KAØAZS


Re: APRSISCE/TN-D710 set-up

Tyler Griffiths
 


Re: APRSISCE/TN-D710 set-up

Randy Allen
 

I've been walking a couple of hams through this recently and finally found time to write up what I have found to work. When I get a chance I'll add screen shots and post to the files section. Hope this helps:


First, read this page on the APRSIS32 Wiki: http://aprsisce.wikidot.com/port:kenwood-tm-d710


Computer Set Up:


Check the baud rate of the COM port you will be using in device manager


Radio Set Up:


Menu 604: COM Port. Set to ON


Menu 929 (AUX, COM PORT, BAUD RATE) Set it to match the baud rate for the computer COM port


Menu 601: INTERNAL TNC, DATA SPEED. That should be set to 1200 bps for APRS work on VHF.


Set TNC to APRS12 or PACKET12 depending on the APRSIS32 port you will be using (see below)


Radio to computer connection.


Connect the data cable being used (such as the Kenwood PG5g) to the computer and the port on the Control Head, not the body of the radio. The port on the body is only for programming the radio (memories, settings, etc.), Echo Link, and connecting with an HF rig. The TNC resides in the control head and that's what that port is for.


APRSIS32 Setup


For the D710, there are 2 pre-canned ports that can set up: KWD710(APRS) and KWD710(PKT).


KWD710(APRS) maintains the radio's internal APRS and GPS features and passes data to the computer. The radio maintains control of transmissions. See full details at the Wiki page linked above.


KWD710(PKT) turns off the radio's APRS features and give full control of the TNC to the computer. In this mode GPS data from the radio is not available.


You start by creating a port: Configure; Ports, New Port.


Use the Type drop down box to select what type of port you are creating. (I would create one of each to make it easier to switch between the different modes with the D710). Name the port whatever you want to find it quickly later.


Click the Create button, then click on the COMn Serial button on the next pop up screen


Set the Port number and Baud rate in the Port Configuration pop up to match the baud rate of the computer's COM port and the COM port on the radio. ( leave the Parity, Data and Stop bits as default, they are pretty standard these days). Click OK.


Make any changes you want to the Port settings (as described in the D710 Wiki page) and click on Accept. (note: the RF Baud is grayed out and fixed at 1200, it has nothing do with the Com port settings)


You set which port you want to use by going to Enables, Ports and clicking on the desired port, putting a check mark next to it. You disable it by clicking on it again and removing the check mark. Match the radio TNC Mode (PACKET12 or APRS12) to the port you are using.

T

he ports and radio TNC settings are a matched pair.

Use the 710 APRS port when the radio set to APRS12

Use the 710 Packet port when the radio is set to PACKET12


For diagnostic purposes I set the scroller to show RF stations only to ensure that I am not seeing stations coming in from an internet connection: Configure; Scroller; check RF Only.


Having an APRS handheld radio (such as my TH-D74) is handy to ensure everything is working and to troubleshoot, particularly if you are in a location with limited RF APRS activity.


Randy KAØAZS


Re: APRSISCE/TN-D710 set-up

Randy Allen
 

I've learned from hard experience that you need to connect the data cable to the Control Head, NOT the radio body when using APRS (specifically APRSIS32).  The TNC resides in the control head.

Respectfully,

Randy Allen KAØAZS


---In aprsisce@..., <va7dgp@...> wrote :

I've only used the head comm port for Winlink Express. I used the data port on the body for everything else.

73

Don Poaps
New Westminster, BC
VA7DGP DATA
VA7QU   VOICE


 




 


Re: APRSISCE/TN-D710 set-up

J Lineback <jelineback@...>
 

Probably dumb questions but have caught me out on occasion… is the TNC switched on, and showing the correct speed?

On Sep 8, 2019, at 1:19 PM, Don Poaps va7dgp@... [aprsisce] <aprsisce@...> wrote:


I've only used the head comm port for Winlink Express. I used the data port on the body for everything else.

73

Don Poaps
New Westminster, BC
VA7DGP DATA
VA7QU   VOICE


Winlink: va7qu@...
Subject://wl2k           



                    
  




 


On Sun, Sep 8, 2019 at 9:54 AM kobvbg3lifoji5e6puvt3avv33qmjisqhwybn7g6@... [aprsisce] <aprsisce@...> wrote:
 

I am running a Dell machine with Windows 10.

Connected to the Dell via the supplied accessory cable supplied by Kenwood and is connected to the D710 on the back of the control head then to a USB port on the Dell.  The Dell does not have a 9 pin connection on the back.


On the computer screen is running the APRSICE/32 software.  When connected to the Internet I see all kinds of stations popping up.  When not connected to the Internet I only see my call AF5AA-1 on the screen.


I have read the documentation on APRSISCE both on the Internet and user's manual.  I do not think I have the set-up correct because reading the documentation I see all kinds of things I am missing.


Is there a detailed description on how to connect and set-up APRSISCE?  I want the D710 to feed the computer with information not the Internet.


Thanks:

Burt

AF5AA.      





Re: APRSISCE/TN-D710 set-up

Don Poaps
 

I've only used the head comm port for Winlink Express. I used the data port on the body for everything else.

73

Don Poaps
New Westminster, BC
VA7DGP DATA
VA7QU   VOICE


Winlink: va7qu@...
Subject://wl2k           



                    
  




 


On Sun, Sep 8, 2019 at 9:54 AM kobvbg3lifoji5e6puvt3avv33qmjisqhwybn7g6@... [aprsisce] <aprsisce@...> wrote:
 

I am running a Dell machine with Windows 10.

Connected to the Dell via the supplied accessory cable supplied by Kenwood and is connected to the D710 on the back of the control head then to a USB port on the Dell.  The Dell does not have a 9 pin connection on the back.


On the computer screen is running the APRSICE/32 software.  When connected to the Internet I see all kinds of stations popping up.  When not connected to the Internet I only see my call AF5AA-1 on the screen.


I have read the documentation on APRSISCE both on the Internet and user's manual.  I do not think I have the set-up correct because reading the documentation I see all kinds of things I am missing.


Is there a detailed description on how to connect and set-up APRSISCE?  I want the D710 to feed the computer with information not the Internet.


Thanks:

Burt

AF5AA.      


APRSISCE/TN-D710 set-up

kobvbg3lifoji5e6puvt3avv33qmjisqhwybn7g6@...
 

I am running a Dell machine with Windows 10.

Connected to the Dell via the supplied accessory cable supplied by Kenwood and is connected to the D710 on the back of the control head then to a USB port on the Dell.  The Dell does not have a 9 pin connection on the back.


On the computer screen is running the APRSICE/32 software.  When connected to the Internet I see all kinds of stations popping up.  When not connected to the Internet I only see my call AF5AA-1 on the screen.


I have read the documentation on APRSISCE both on the Internet and user's manual.  I do not think I have the set-up correct because reading the documentation I see all kinds of things I am missing.


Is there a detailed description on how to connect and set-up APRSISCE?  I want the D710 to feed the computer with information not the Internet.


Thanks:

Burt

AF5AA.      


Re: New Kenwood TM-D710GA

KD7YZ Bob
 

The email tells me three jpegs “were” sent.
What is property procedure to attach pix via the email route?


New Kenwood TM-D710GA

KD7YZ Bob
 

I require some D710GA mentoring in order to get the "best/most" out of APRSIS32 here.

Thanks to Randy KAØAZS, I have in front of me the :

http://aprsisce.wikidot.com/port:kenwood-tm-d710

page.

That read, I still do not believe I have cabling correct no APRSIS32 settings right.

I have the DB9 to a RadioShack like DB9 to USB connector into the radio "COM socket. This produces Com9 at 19200 baud.

I have the programming cable from RT systems (gray) into a"PC" and that USB plugs into, or results in, Com15 also at 19200 B.

The rig came with a plug whic ONLY would plug into radio DATA socket. That one has a green and a purple(like) 3-pole plug. I have not plugged it in cuz I simply am too dumb to know where it should reside.


My lashup allows me to occasionally send out a strange beacon containing info about battery charging. Nonetheless, I am 'beaconing' and it show up on FindU and APRS.

My 'beaconing' screenshot shows the Hose Symbol dead-center, which is where I am (fwiw).

My goal, after u optimize my lashup, is to let PstRotator trACK SOME OF THE APRS SATELLITES. A WEEK AGO AND BEFORE THE NEW kENWO0OD, i WAS GRABBING TO OCCASIONAL PACKET FROM bRICSAT AND iss ETc.

thanks for the help Lads.

This is important to me as I am a wee bit laid-up ... which willl no doubt cost me a couple months sanity ... thus getting this to work and thus entertain my mind will be a large relief to XYL and me.

PS .. hope screenshots (3) can pass through here.
--
73
Bob KD7YZ
AMSAT LM #901


Re: Development mode [1 Attachment]

Christopher Rose
 

No attachment showed up

-----------------------------------------

From: "shoan butler kn4txm@... [aprsisce]"
To: "aprsisce@..."
Cc:
Sent: Thursday September 5 2019 10:36:46PM
Subject: RE: [aprsisce] Development mode [1 Attachment]

 
[Attachment(s) from shoan butler included below]

I have tried everything. I got the notepad finally and changed the update development to one but after trying ctrl O for satellite forecasting I still get block. Does anyone have capability to remote in and see what the issue is? I bought this laptop solely to use this program. Not a personal storage.

 

Sent from Mail for Windows 10

 

From: Rob Giuliano kb8rco@... [aprsisce]
Sent: Thursday, September 5, 2019 10:11 PM
To: shoan butler kn4txm@... [aprsisce]
Subject: Re: [aprsisce] Development mode

 

 

Not sure if anyone replied, but it is as simple as:

(Assuming windows)

0. Close APRSIS32 (or make sure it is closed)

    editing the file while open will not work as it gets overwritten on close

1. Open Windows File Explorer

2. Navigate to the subfolder where aprsis32.exe and supporting files are (should also have a subfolder OSMTiles).

3. Looking at the files, there should be :

   a) APRSIS32.exe

   b) APRSIS32.xml

   c) APRSIS32.log, plus any number of APRSIS32##.log files

4. Left click on the APRSIS32.xml and choose Edit

    This will open the file for editing in the default text editing file - typically Notepad.exe

5. Press f

    in the Find what: text box type devel then press

6. Chnage the line that you go to from

    0

          to

    1

7. Save and Close the text editor

8. Now back in File Explorer

    Double click on APRSIS32.exe to start the app and allow it to upgrade the system and restart

 

That's it!

Robert Giuliano
KB8RCO

 

 

On Thursday, September 5, 2019, 7:34:03 PM EDT, shoan butler kn4txm@... [aprsisce] wrote:

 

 

 

Does anyone have a minute to run me through this development mode setup???? Would really appreciate it.

 

Sent from Mail for Windows 10

 

From: 'Michael Wright' mfwright@... [aprsisce]
Sent: Thursday, September 5, 2019 2:15 PM
To: aprsisce@...
Subject: Re: [aprsisce] Development mode

 

 

Lynn,

Thanks for your on-going support for APRSISCE.

Mike K6MFW

 

 


How do I change default MultiTrack screen?

Arnold Harding - KQ6DI
 

My MultiTrack screen always comes up dim and a larger window than my computer screen, so I ALWAYS need to brighten the screen and work at resizing it.

My question is how do I change the default MultiTrack screen to something else?  Or how the heck did it get wrong like this?

Arnold, KQ6DI


Re: Development mode [1 Attachment]

Glenn O'Connor <kf0ed@...>
 

Internet access checked and CTRL+O applied. Voila!

 

Birds!

 

From: aprsisce@...
Sent: Thursday, September 05, 2019 9:34 PM
To: aprsisce@...
Subject: RE: [aprsisce] Development mode [1 Attachment]

 

 

[Attachment(s) from shoan butler included below]

I have tried everything. I got the notepad finally and changed the update development to one but after trying ctrl O for satellite forecasting I still get block. Does anyone have capability to remote in and see what the issue is? I bought this laptop solely to use this program. Not a personal storage.

 

Sent from Mail for Windows 10

 

From: Rob Giuliano kb8rco@... [aprsisce]
Sent: Thursday, September 5, 2019 10:11 PM
To: shoan butler kn4txm@... [aprsisce]
Subject: Re: [aprsisce] Development mode

 

 

Not sure if anyone replied, but it is as simple as:

(Assuming windows)

0. Close APRSIS32 (or make sure it is closed)

    editing the file while open will not work as it gets overwritten on close

1. Open Windows File Explorer

2. Navigate to the subfolder where aprsis32.exe and supporting files are (should also have a subfolder OSMTiles).

3. Looking at the files, there should be :

   a) APRSIS32.exe

   b) APRSIS32.xml

   c) APRSIS32.log, plus any number of APRSIS32##.log files

4. Left click on the APRSIS32.xml and choose Edit

    This will open the file for editing in the default text editing file - typically Notepad.exe

5. Press f

    in the Find what: text box type devel then press

6. Chnage the line that you go to from

    0

          to

    1

7. Save and Close the text editor

8. Now back in File Explorer

    Double click on APRSIS32.exe to start the app and allow it to upgrade the system and restart

 

That's it!

Robert Giuliano
KB8RCO

 

 

On Thursday, September 5, 2019, 7:34:03 PM EDT, shoan butler kn4txm@... [aprsisce] <aprsisce@...> wrote:

 

 

 

Does anyone have a minute to run me through this development mode setup???? Would really appreciate it.

 

Sent from Mail for Windows 10

 

From: 'Mich! ael Wright' mfwright@... [aprsisce]
Sent: Thursday, September 5, 2019 2:15 PM
To: aprsisce@...
Subject: Re: [aprsisce] Development mode

 

 

Lynn,

Thanks for your on-going support for APRSISCE.

Mike K6MFW

 

 


Re: Development mode [1 Attachment]

Lynn Deffenbaugh
 

After restarting APRSISCE/32, you have to look at About to see that you are running the Development version and to allow it to download the latest version.  After that restart, Control-O should work.  At least, provided that the About box indicates that you have successfully switched to Development.

Lynn (D) - KJ4ERJ - Author of APRSISCE for Windows Mobile and Win32

On 9/5/2019 10:34 PM, shoan butler kn4txm@... [aprsisce] wrote:

I have tried everything. I got the notepad finally and changed the update development to one but after trying ctrl O for satellite forecasting I still get block. Does anyone have capability to remote in and see what the issue is? I bought this laptop solely to use this program. Not a personal storage.

 

Sent from Mail for Windows 10

 

From: Rob Giuliano kb8rco@... [aprsisce]
Sent: Thursday, September 5, 2019 10:11 PM
To: shoan butler kn4txm@... [aprsisce]
Subject: Re: [aprsisce] Development mode

 

 

Not sure if anyone replied, but it is as simple as:

(Assuming windows)

0. Close APRSIS32 (or make sure it is closed)

    editing the file while open will not work as it gets overwritten on close

1. Open Windows File Explorer

2. Navigate to the subfolder where aprsis32.exe and supporting files are (should also have a subfolder OSMTiles).

3. Looking at the files, there should be :

   a) APRSIS32.exe

   b) APRSIS32.xml

   c) APRSIS32.log, plus any number of APRSIS32##.log files

4. Left click on the APRSIS32.xml and choose Edit

    This will open the file for editing in the default text editing file - typically Notepad.exe

5. Press f

    in the Find what: text box type devel then press

6. Chnage the line that you go to from

    0

          to

    1

7. Save and Close the text editor

8. Now back in File Explorer

    Double click on APRSIS32.exe to start the app and allow it to upgrade the system and restart

 

That's it!

Robert Giuliano
KB8RCO

 

 

On Thursday, September 5, 2019, 7:34:03 PM EDT, shoan butler kn4txm@... [aprsisce] wrote:

 

 

 

Does anyone have a minute to run me through this development mode setup???? Would really appreciate it.

 

Sent from Mail for Windows 10

 

From: 'Michael Wright' mfwright@... [aprsisce]
Sent: Thursday, September 5, 2019 2:15 PM
To: aprsisce@...
Subject: Re: [aprsisce] Development mode

 

 

Lynn,

Thanks for your on-going support for APRSISCE.

Mike K6MFW

 

 


Re: Development mode

shoan butler
 

I have tried everything. I got the notepad finally and changed the update development to one but after trying ctrl O for satellite forecasting I still get block. Does anyone have capability to remote in and see what the issue is? I bought this laptop solely to use this program. Not a personal storage.

 

Sent from Mail for Windows 10

 

From: Rob Giuliano kb8rco@... [aprsisce]
Sent: Thursday, September 5, 2019 10:11 PM
To: shoan butler kn4txm@... [aprsisce]
Subject: Re: [aprsisce] Development mode

 

 

Not sure if anyone replied, but it is as simple as:

(Assuming windows)

0. Close APRSIS32 (or make sure it is closed)

    editing the file while open will not work as it gets overwritten on close

1. Open Windows File Explorer

2. Navigate to the subfolder where aprsis32.exe and supporting files are (should also have a subfolder OSMTiles).

3. Looking at the files, there should be :

   a) APRSIS32.exe

   b) APRSIS32.xml

   c) APRSIS32.log, plus any number of APRSIS32##.log files

4. Left click on the APRSIS32.xml and choose Edit

    This will open the file for editing in the default text editing file - typically Notepad.exe

5. Press f

    in the Find what: text box type devel then press

6. Chnage the line that you go to from

    0

          to

    <Update.Development>1

7. Save and Close the text editor

8. Now back in File Explorer

    Double click on APRSIS32.exe to start the app and allow it to upgrade the system and restart

 

That's it!

Robert Giuliano
KB8RCO

 

 

On Thursday, September 5, 2019, 7:34:03 PM EDT, shoan butler kn4txm@... [aprsisce] <aprsisce@...> wrote:

 

 

 

Does anyone have a minute to run me through this development mode setup???? Would really appreciate it.

 

Sent from Mail for Windows 10

 

From: 'Michael Wright' mfwright@... [aprsisce]
Sent: Thursday, September 5, 2019 2:15 PM
To: aprsisce@...
Subject: Re: [aprsisce] Development mode

 

 

Lynn,

Thanks for your on-going support for APRSISCE.

Mike K6MFW

 

 


Re: Development mode

Rob Giuliano
 

Not sure if anyone replied, but it is as simple as:
(Assuming windows)
0. Close APRSIS32 (or make sure it is closed)
    editing the file while open will not work as it gets overwritten on close
1. Open Windows File Explorer
2. Navigate to the subfolder where aprsis32.exe and supporting files are (should also have a subfolder OSMTiles).
3. Looking at the files, there should be :
   a) APRSIS32.exe
   b) APRSIS32.xml
   c) APRSIS32.log, plus any number of APRSIS32##.log files
4. Left click on the APRSIS32.xml and choose Edit
    This will open the file for editing in the default text editing file - typically Notepad.exe
5. Press f
    in the Find what: text box type devel then press
6. Chnage the line that you go to from
   
          to
    1
7. Save and Close the text editor
8. Now back in File Explorer
    Double click on APRSIS32.exe to start the app and allow it to upgrade the system and restart

That's it!

Robert Giuliano
KB8RCO



On Thursday, September 5, 2019, 7:34:03 PM EDT, shoan butler kn4txm@... [aprsisce] wrote:


 

Does anyone have a minute to run me through this development mode setup???? Would really appreciate it.

 

Sent from Mail for Windows 10

 

From: 'Michael Wright' mfwright@... [aprsisce]
Sent: Thursday, September 5, 2019 2:15 PM
To: aprsisce@...
Subject: Re: [aprsisce] Development mode

 

 

Lynn,

Thanks for your on-going support for APRSISCE.

Mike K6MFW

 


Re: Development mode

Glenn OConnor <kf0ed@...>
 

Find the pertinent .xml file, APRSIS32. 
Open with Notepad. Find, by using Ctrl+F tool, 
for the <> made be a prior poster. Make the edit, save, start the program.


On Thu, Sep 5, 2019 at 18:34, shoan butler kn4txm@... [aprsisce]
wrote:
 

Does anyone have a minute to run me through this development mode setup???? Would really appreciate it.

 

Sent from Mail for Windows 10

 

From: 'Michael Wright' mfwright@... [aprsisce]
Sent: Thursday, September 5, 2019 2:15 PM
To: aprsisce@...
Subject: Re: [aprsisce] Development mode

 

 

Lynn,

Thanks for your on-going support for APRSISCE.

Mike K6MFW

 


Re: Development mode

shoan butler
 

Does anyone have a minute to run me through this development mode setup???? Would really appreciate it.

 

Sent from Mail for Windows 10

 

From: 'Michael Wright' mfwright@... [aprsisce]
Sent: Thursday, September 5, 2019 2:15 PM
To: aprsisce@...
Subject: Re: [aprsisce] Development mode

 

 

Lynn,

Thanks for your on-going support for APRSISCE.

Mike K6MFW

 


Re: Development mode

KP3FT
 

OK, good to know.  I've used both here without issue, but then again, maybe it did change some things in the file that affects APRSis32 in a bad way.  I'll use NotePad from now on.

On Thursday, September 5, 2019, 10:53:54 AM EDT, 'Lynn W Deffenbaugh (Mr)' kj4erj@... [aprsisce] wrote:


 

Please do NOT use WordPad or MS Word.  They are not pure text editors and may add things to the file that are not good.

NotePad is a pure text editor and is much more appropriate to this change.


Lynn (D) - KJ4ERJ - Author of APRSISCE for Windows Mobile and Win32

On 9/5/2019 9:41 AM, Jeff KP3FT kp3ft@... [aprsisce] wrote:
Open the APRSIS32.XML file in WordPad or MS Word, scroll down close to the bottom, and look for the line:

0

Change the 0 to 1, save the file, restart the APRSis32 program, then click "About" in its menu.

On Thursday, September 5, 2019, 9:26:20 AM EDT, shoan butler kn4txm@... [aprsisce] wrote:


 

My xml wont allow me to make changes, there is no box to change anything as described its just a bunch of fixed code. The wiki said something about changing 0's to 1's but thete is no option to change anything on here????


On Thu, Sep 5, 2019 at 4:43 AM, Ryszard Labus r.labus@... [aprsisce]
wrote:
 

Check this out:

http://aprsisce.wikidot.com/doc:development-version

R.

W dniu 2019-09-05 o 04:19, shoan butler kn4txm@... [aprsisce] pisze:
 

Hi all, when I try to track satellites by entering Ctrl + O the system rejects it stating that I can only execute this in development mode. Where do I even start????

 

Sent from Mail for Windows 10

 

--
SINUX Ryszard Labus
ul. Domaniewska 47/10 02-672 Warszawa
NIP: 548-138-01-53    tel: 666385002
          r.labus@...
http://sinux.pl   http://sinux.com.pl

1581 - 1600 of 35243