Date   

Re: Winlink Notifications via aprsi32

Lynn Deffenbaugh
 

I beg to differ.  It seems the text is WINLINK per http://www.winlink.org/APRSLink

If you desire notification of pending Winlink email just add "WINLINK" somewhere in your station's position comment (or status text) and you'll be notified with an APRS message whenever you have unread mail on the Winlink system. Notification is sent once per day (when it's detected that your station is on-line) but is reset whenever you use APRSLink to access your Winlink email. In that way, mail received after you have read the current batch of messages will trigger another notification.
So, if anyone is using this, which is it?  WINLINK or WLNK-1 (which is the station to which the queries can be sent)?

Lynn (D) - KJ4ERJ - Author of APRSISCE for Windows Mobile and Win32



On 3/30/2015 1:26 AM, helge@... [aprsisce] wrote:
Hi folks,

WLNK-1 is the text that has to be integrated at some place in your beacon comment !

Once you fire up the transceiver in the morning that text fragment is dicovered by the APRS-IS it is then forwarded to the WLNK-1 server.

If any Winlink message is available it sends out the notifiction automatically. This process works at least once in 24 hours time. It is not good for an instant notification the minute after a Winlink mesaage appears in the box.

The manual action for this would be a query to address WLNK-1 texting the letter L (list my messages).

Further as in the link of the previous reply or find a link on http://robust-packet.net navigation bar. On the APRSlink page there are even 2 PDFs of which one carries the commands only.

Again: key element ist the wording WLNK-1 a some place in the beacon comment. Some have it the very end (then depending on the total length of the comment sometimes even unvisable on aprs.fi map page [limited to 67? letters or so] but still valid for the process to happen)

73
Helge, DF8LS
RPN Europe Admin

| Robust-Packet-Network | _____________________________________________________________________________________________________________________________________________________________________________________________________________________


Re: Winlink Notifications via aprsi32

Jerry N7YGE
 

 

 

From: aprsisce@... [mailto:aprsisce@...]
Sent: Sunday, March 29, 2015 10:27 PM
To: aprsisce@...
Subject: RE: [aprsisce] Winlink Notifications via aprsi32

 

 

Hi folks,

WLNK-1 is the text that has to be integrated at some place in your beacon comment !

Once you fire up the transceiver in the morning that text fragment is dicovered by the APRS-IS it is then forwarded to the WLNK-1 server.

If any Winlink message is available it sends out the notifiction automatically. This process works at least once in 24 hours time. It is not good for an instant notification the minute after a Winlink mesaage appears in the box.

The manual action for this would be a query to address WLNK-1 texting the letter L (list my messages).

Further as in the link of the previous reply or find a link on http://robust-packet.net navigation bar. On the APRSlink page there are even 2 PDFs of which one carries the commands only.

Again: key element ist the wording WLNK-1 a some place in the beacon comment. Some have it the very end (then depending on the total length of the comment sometimes even unvisable on aprs.fi map page [limited to 67? letters or so] but still valid for the process to happen)

73
Helge, DF8LS
RPN Europe Admin

| Robust-Packet-Network | _____________________________________________________________________________________________________________________________________________________________________________________________________________________


Re: Winlink Notifications via aprsi32

helge@...
 

Hi folks,

WLNK-1 is the text that has to be integrated at some place in your beacon comment !

Once you fire up the transceiver in the morning that text fragment is dicovered by the APRS-IS it is then forwarded to the WLNK-1 server.

If any Winlink message is available it sends out the notifiction automatically. This process works at least once in 24 hours time. It is not good for an instant notification the minute after a Winlink mesaage appears in the box.

The manual action for this would be a query to address WLNK-1 texting the letter L (list my messages).

Further as in the link of the previous reply or find a link on http://robust-packet.net navigation bar. On the APRSlink page there are even 2 PDFs of which one carries the commands only.

Again: key element ist the wording WLNK-1 a some place in the beacon comment. Some have it the very end (then depending on the total length of the comment sometimes even unvisable on aprs.fi map page [limited to 67? letters or so] but still valid for the process to happen)

73
Helge, DF8LS
RPN Europe Admin

| Robust-Packet-Network | _____________________________________________________________________________________________________________________________________________________________________________________________________________________


Re: Winlink Notifications via aprsi32

Greg Depew
 

Check out this link that winlink  has provided 

http://www.winlink.org/APRSLink

Greg KB3KBR Sent from my Verizon Wireless 4G LTE smartphone


-------- Original message --------
From: "wb2lmv wb2lmv@... [aprsisce]"
Date: 03/29/2015 19:02 (GMT-05:00)
To: aprsisce@...
Subject: Re: [aprsisce] Winlink Notifications via aprsi32

 

The person to contact is Jeremy N1ZZZ. His email address is listed on QRZ.com. He does just that when he is out to sea. He somehow has APRS messaging alert him that he has Winlink email.


73 de Glenn WB2LMV


-----Original Message-----
From: 'Lynn W Deffenbaugh (Mr)' kj4erj@... [aprsisce]
To: aprsisce
Sent: Sun, Mar 29, 2015 6:43 pm
Subject: Re: [aprsisce] Winlink Notifications via aprsi32

 
First you'll need a Winlink guru to show me what the notifications actually are, and then we can talk about getting them (selectively) from -IS to RF.

Lynn (D) - KJ4ERJ - Author of APRSISCE for Windows Mobile and Win32

On 3/29/2015 4:26 PM, Bob Harris knineudx@... [aprsisce] wrote:
A fellow ham wants to use aprsis32 to forward Winlink notifications from aprs-is to rf so he can get them and read the messages on his Kenwood mobile transceiver.

Since I am not a Winlink user and the stuff I have found on the web is obscure to me, I cannot give him much help. I have learned (I think) that the notifications are messages from one of the Winlink servers and should be on aprs-is. After that I'm lost.

Is there a message guru (Lynn?) that can help us?
--
Bob Harris (K9UDX)
Can MOTCH Katmai Henry David Thoreau UDX Bda UD (1992-2005)
Longmeadow Bradford Torrey CD (2001-2014)
Ch Silvercreek Gossip Girl
Bath, NH


Re: Winlink Notifications via aprsi32

wb2lmv <wb2lmv@...>
 

The person to contact is Jeremy N1ZZZ. His email address is listed on QRZ.com. He does just that when he is out to sea. He somehow has APRS messaging alert him that he has Winlink email.

73 de Glenn WB2LMV


-----Original Message-----
From: 'Lynn W Deffenbaugh (Mr)' kj4erj@... [aprsisce]
To: aprsisce
Sent: Sun, Mar 29, 2015 6:43 pm
Subject: Re: [aprsisce] Winlink Notifications via aprsi32

 
First you'll need a Winlink guru to show me what the notifications actually are, and then we can talk about getting them (selectively) from -IS to RF.

Lynn (D) - KJ4ERJ - Author of APRSISCE for Windows Mobile and Win32

On 3/29/2015 4:26 PM, Bob Harris knineudx@... [aprsisce] wrote:
A fellow ham wants to use aprsis32 to forward Winlink notifications from aprs-is to rf so he can get them and read the messages on his Kenwood mobile transceiver.

Since I am not a Winlink user and the stuff I have found on the web is obscure to me, I cannot give him much help. I have learned (I think) that the notifications are messages from one of the Winlink servers and should be on aprs-is. After that I'm lost.

Is there a message guru (Lynn?) that can help us?
--
Bob Harris (K9UDX)
Can MOTCH Katmai Henry David Thoreau UDX Bda UD (1992-2005)
Longmeadow Bradford Torrey CD (2001-2014)
Ch Silvercreek Gossip Girl
Bath, NH


Re: Winlink Notifications via aprsi32

Lynn Deffenbaugh
 

First you'll need a Winlink guru to show me what the notifications actually are, and then we can talk about getting them (selectively) from -IS to RF.

Lynn (D) - KJ4ERJ - Author of APRSISCE for Windows Mobile and Win32

On 3/29/2015 4:26 PM, Bob Harris knineudx@... [aprsisce] wrote:
A fellow ham wants to use aprsis32 to forward Winlink notifications from aprs-is to rf so he can get them and read the messages on his Kenwood mobile transceiver.

Since I am not a Winlink user and the stuff I have found on the web is obscure to me, I cannot give him much help. I have learned (I think) that the notifications are messages from one of the Winlink servers and should be on aprs-is. After that I'm lost.

Is there a message guru (Lynn?) that can help us?
--

Bob Harris (K9UDX)
Can MOTCH Katmai Henry David Thoreau UDX Bda UD (1992-2005)
Longmeadow Bradford Torrey CD (2001-2014)
Ch Silvercreek Gossip Girl
Bath, NH



Winlink Notifications via aprsi32

robt.harris
 

A fellow ham wants to use aprsis32 to forward Winlink notifications from aprs-is to rf so he can get them and read the messages on his Kenwood mobile transceiver.

Since I am not a Winlink user and the stuff I have found on the web is obscure to me, I cannot give him much help. I have learned (I think) that the notifications are messages from one of the Winlink servers and should be on aprs-is. After that I'm lost.

Is there a message guru (Lynn?) that can help us?
--

Bob Harris (K9UDX)
Can MOTCH Katmai Henry David Thoreau UDX Bda UD (1992-2005)
Longmeadow Bradford Torrey CD (2001-2014)
Ch Silvercreek Gossip Girl
Bath, NH


Re: Quiet Time and RF Port

n2nf@...
 

Found the issue.  Setting the value of Quiet Time in Configure>General only changes the Quiet Time value for the APRS-IS port.  I had change the Quiet Time value from Configure>Ports>(144.390) to set it to 180 seconds.  It was still set for 60 seconds.

Bob N2NF


Re: Quiet Time and RF Port

n2nf@...
 

I set the Quiet Time for 180 sec. in the Configure>General Window.  After allowing the application to run for hours, I'm finding that the RF port will close and reopen after 60 seconds of no activity regardless of the Quiet Time value.

A review of the TRACE log for my RF port (144.390) shows the port terminating after 60014 msec vs 60000 Quiet, even though the value is set for 180 sec.

Is there another parameter that I should be looking at, or can I edit the XML file to change the value.

Bob, N2NF


Re: Quiet Time and RF Port

Lynn Deffenbaugh
 

I discovered on my own IGate's Bluetooth-linked TNC, the maximum value of 300 seconds (5 minutes) is long enough for most of the time, but when 2m closes down, I can no longer decode some of the further digipeaters and recently the closest digipeater is not working as well, so sometimes the connection closes and opens due to the Quiet Time setting.

In some upcoming release, I may increase the maximum allowed value to 900 (15 minutes) to account for this.

Lynn (D) - KJ4ERJ - Author of APRSISCE for Windows Mobile and Win32



On 3/28/2015 11:16 AM, James Ewen ve6srv@... [aprsisce] wrote:
Yes.


The Quiet Time is the maximum length of time during which a packet should have been heard on that port. If no packet is heard within the specified time, the port is closed and re-opened using all of the configure s. This is provided as a way to detect a possibly dropped network or bluetooth connection, or maybe even a TNC that has lost its mode and needs a restart to recover. Because there is no heartbeat/keepalive capability on a TNC connection, an RF Port Quiet Time must be set long enough to cover the maximum expected elapsed time between packet receptions. If set too short, the port will unnecessarily close and re-open itself periodically, possibly resulting in dropped packets across the restart. A Quiet Time of zero disables this function.

So, don't set this on a KISS-type port on a Kenwood radio. The default s will leave the radio's TNC turned off until you manually turn it back on.

Don't set this on any port that doesn't have a steady stream of expected traffic (like an HF APRS radio port). It just doesn't work out very well.

If you have a steady APRS traffic hum on your radio port, set the Quiet Time to 2-3 TIMES the quiet time you'd expect to see on the channel. This gives APRSISCE/32 a chance to reset the channel if it goes quiet too long. If you have sounds enabled, you'll heard bings and bongs while the radio port transitions through the various states of a restart.


James
VE6SRV

On Sat, Mar 28, 2015 at 8:32 AM, n2nf@... [aprsisce] <aprsisce@...> wrote:


The RF port in my case labeled 144.390 periodically will close and reopen.  I read the help file on quiet time and understood this as a parameter for APRS-IS internet  port.  Is it normal behavior for the RF port to close and reopen in accordance with the quiet time setting?

 

Bob, N2NF






Re: Quiet Time and RF Port

n2nf@...
 

James, thanks for the explanation.  Here I am using a Timewave TNC in KISS mode on a 2 Meter RF with a fair amount of activity, so I'm thinking experimenting with quiet time of 3 to 5 minutes.
Thanks agian,
Bob, N2NF


Re: Quiet Time and RF Port

James Ewen
 

Yes.


The Quiet Time is the maximum length of time during which a packet should have been heard on that port. If no packet is heard within the specified time, the port is closed and re-opened using all of the configure s. This is provided as a way to detect a possibly dropped network or bluetooth connection, or maybe even a TNC that has lost its mode and needs a restart to recover. Because there is no heartbeat/keepalive capability on a TNC connection, an RF Port Quiet Time must be set long enough to cover the maximum expected elapsed time between packet receptions. If set too short, the port will unnecessarily close and re-open itself periodically, possibly resulting in dropped packets across the restart. A Quiet Time of zero disables this function.

So, don't set this on a KISS-type port on a Kenwood radio. The default s will leave the radio's TNC turned off until you manually turn it back on.

Don't set this on any port that doesn't have a steady stream of expected traffic (like an HF APRS radio port). It just doesn't work out very well.

If you have a steady APRS traffic hum on your radio port, set the Quiet Time to 2-3 TIMES the quiet time you'd expect to see on the channel. This gives APRSISCE/32 a chance to reset the channel if it goes quiet too long. If you have sounds enabled, you'll heard bings and bongs while the radio port transitions through the various states of a restart.


James
VE6SRV

On Sat, Mar 28, 2015 at 8:32 AM, n2nf@... [aprsisce] <aprsisce@...> wrote:


The RF port in my case labeled 144.390 periodically will close and reopen.  I read the help file on quiet time and understood this as a parameter for APRS-IS internet  port.  Is it normal behavior for the RF port to close and reopen in accordance with the quiet time setting?

 

Bob, N2NF





Quiet Time and RF Port

n2nf@...
 

The RF port in my case labeled 144.390 periodically will close and reopen.  I read the help file on quiet time and understood this as a parameter for APRS-IS internet  port.  Is it normal behavior for the RF port to close and reopen in accordance with the quiet time setting?

 

Bob, N2NF


Re: APRSis-32 and the Kenwood tmd72 what i learnt

sean grant
 

hiya Lynn

thank you for your reply i will check this but i found if i turn off APRSIS SSID  Beacon and just follow the handie SSID it worked ok and it followed me everywhere i went which is what i wanted.

As for the handie SSID disappearing when i get out off range of a digi repeater  i found when the handie transmitted it showed up straight away on the map the handie settings for transmit are smart beaconing so it follows every turn most off the time i will do some more tests just to make sure but i feel it is doing what im asking for 

again thank you for your input 

73

Sean 
M3SGO 2E0BTL M0XAN 


Re: WX Object Question

Carl Davis
 

KA1UDX-1 has been a problem station for a long time in this area.  Delaying packets, gating everything from IS to RF.  He has reset it in the past and made changes but it goes back to clogging things up around here.
 
Carl,KB1EJH


From: "'Lynn W Deffenbaugh (Mr)' kj4erj@... [aprsisce]"
To: aprsisce@...
Sent: Thursday, March 26, 2015 3:32 PM
Subject: Re: [aprsisce] WX Object Question



Please e-mail your APRSIS32.XML file to me at KJ4ERJ@....  I suspect you've got some extra objects configured, but I'd like to check the configuration to be sure.

And just to confuse matters, I suspect the KA1UDX-1 IGate is running a KPC-3+ in KISS mode and is delaying delivery of packets to the APRS-IS.  If you have the ability to include timestamps from your WX2NJ-13 station, we would see this even more readily.

Lynn (D) - KJ4ERJ - Author of APRSISCE for Windows Mobile and Win32

On 3/26/2015 2:18 PM, wx2nj@... [aprsisce] wrote:
Home station is WX2NJ-14 with a Yagi-Home icon. Created New Weather Object of WX2NJ with WX icon. Both are being transmitted only on RF and not IS. The weather data is being obtained from Peet Weather Text APRS file, wttaprs.txt and is updated every minute.
Why is the weather data being transmitted over both WX2NJ-14 and WX2NJ? Also, the Icon shown on the Internet for the WX2NJ is the blue WX icon and not the Yagi-House.







Re: WX Object Question

Lynn Deffenbaugh
 

Please e-mail your APRSIS32.XML file to me at KJ4ERJ@....  I suspect you've got some extra objects configured, but I'd like to check the configuration to be sure.

And just to confuse matters, I suspect the KA1UDX-1 IGate is running a KPC-3+ in KISS mode and is delaying delivery of packets to the APRS-IS.  If you have the ability to include timestamps from your WX2NJ-13 station, we would see this even more readily.

Lynn (D) - KJ4ERJ - Author of APRSISCE for Windows Mobile and Win32

On 3/26/2015 2:18 PM, wx2nj@... [aprsisce] wrote:
Home station is WX2NJ-14 with a Yagi-Home icon. Created New Weather Object of WX2NJ with WX icon. Both are being transmitted only on RF and not IS. The weather data is being obtained from Peet Weather Text APRS file, wttaprs.txt and is updated every minute.

Why is the weather data being transmitted over both WX2NJ-14 and WX2NJ? Also, the Icon shown on the Internet for the WX2NJ is the blue WX icon and not the Yagi-House.




Re: APRSis-32 and the Kenwood tmd72 what i learnt

Lynn Deffenbaugh
 

On 3/26/2015 11:43 AM, m3sgo@hotmail.co.uk [aprsisce] wrote:


10. what will happen is the SSID thats from the handheld (M0XAN-7) will beacon and will show up on the map and this is the one if you right click and follow will move you round the map with you
I suspect that M0XAN-7 will quit moving when/if you get out of range of any digipeater.

Lynn (D) - KJ4ERJ - Author of APRSISCE for Windows Mobile and Win32


Re: APRSis-32 and the Kenwood tmd72 what i learnt

Lynn Deffenbaugh
 

On 3/26/2015 11:43 AM, m3sgo@hotmail.co.uk [aprsisce] wrote:

10. what will happen is the SSID thats from the handheld (M0XAN-7) will beacon and will show up on the map and this is the one if you right click and follow will move you round the map with you

anyway thats is as far as ive got with the software i think next will be how to use the message system but i will leave that for another day
Brace yourself because when you transmit a message on RF, the D72 will adopt the APRSIS32 callsign-SSID and then your follow will quit working because M0XAN-7 won't beacon until after the next radio power cycle.

Lynn (D) - KJ4ERJ - Author of APRSISCE for Windows Mobile and Win32


WX Object Question

WX2NJ
 

Home station is WX2NJ-14 with a Yagi-Home icon. Created New Weather Object of WX2NJ with WX icon. Both are being transmitted only on RF and not IS. The weather data is being obtained from Peet Weather Text APRS file, wttaprs.txt and is updated every minute.

Why is the weather data being transmitted over both WX2NJ-14 and WX2NJ? Also, the Icon shown on the Internet for the WX2NJ is the blue WX icon and not the Yagi-House.


73, Bob, WX2NJ


APRSis-32 and the Kenwood tmd72 what i learnt

sean grant
 

first of all i must thank everyone for replying to my ask for help

i know have the system working how i want it to work ie track me and show everyone.

while doing this i found some interesting things thanks to all help so let me tell you how i did it 

1. first off all quite simple i loaded the software on to a windows 7 note book then i updated the software i think this was important.

2. i filled in the relevant details  ie call sign  etc( M0XAN-1) 

3.  conected handheld and loaded up the relevent drivers for the notebook to talk to (important) 

4. i went to the config setting and open up a port i used the pre configured KWD710(aprs)and told it what com port to look at mine was 3 

5. now you need to set up the SSID on the handheld (this is were i went wrong and thanks to you all for your help ) mine is M0XAN-7

6. also you need to make sure the settings on the handheld is talking to the computer this is simple just open pc port (menu 350)

7.  set frequency in the UK its 144.800Mhz 

8.  now you should be receiving data 

9. Now comes the hard bit you will find that the handheld and the software will want to beacon both SSID's goto enables tab on in the software drop down the menu and un click beaconing enabled and that will stop the software telling the handheld to stop transmitting the software SSID (in my case M0XAN-1 ) 

now your thinking but it still showing on the screen yes it will but there will be no RF/internet beaconing from that SSID.

10. what will happen is the SSID thats from the handheld (M0XAN-7) will beacon and will show up on the map  and this is the one if you right click and follow will move you round the map with you 


anyway thats is as far as ive got with the software i think next will be how to use the message system but i will leave that for another day 


Again thank you for your help and i hope the above helps others out there too 


73's


Sean 

M3SGO 2E0BTL M0XAN 

8621 - 8640 of 35996